[PATCH 05/10] mmc: aspeed: Adjust delay taps calculation method
Andrew Jeffery
andrew at aj.id.au
Tue Oct 26 14:10:03 AEDT 2021
Hi Chin-Ting,
I think we can split this up a bit:
On Wed, 22 Sep 2021, at 20:01, Chin-Ting Kuo wrote:
> - The maximum tap delay may be slightly different on
> different platforms. It may also be different due to
> different SoC processes or different manufacturers.
> Thus, the maximum tap delay should be gotten from the
> device tree through max-tap-delay property.
I think this could be a patch on its own
> - The delay time for each tap is an absolute value which
> is independent of clock frequency. But, in order to combine
> this principle with "phase" concept, clock frequency is took
> into consideration during calculating delay taps.
> - The delay cell of eMMC device is non-uniform.
> The time period of the first tap is two times of others.
Again, this could be a patch of its own
> - The clock phase degree range is from -360 to 360.
> But, if the clock phase signedness is negative, clock signal
> is output from the falling edge first by default and thus, clock
> signal is leading to data signal by 90 degrees at least.
This line of development is impacted by my comment on an earlier patch
in the series, so should be its own patch.
>
> Signed-off-by: Chin-Ting Kuo <chin-ting_kuo at aspeedtech.com>
> ---
> drivers/mmc/host/sdhci-of-aspeed.c | 115 ++++++++++++++++++++++-------
> 1 file changed, 89 insertions(+), 26 deletions(-)
>
> diff --git a/drivers/mmc/host/sdhci-of-aspeed.c
> b/drivers/mmc/host/sdhci-of-aspeed.c
> index c6eaeb02e3f9..739c9503a5ed 100644
> --- a/drivers/mmc/host/sdhci-of-aspeed.c
> +++ b/drivers/mmc/host/sdhci-of-aspeed.c
> @@ -44,6 +44,7 @@ struct aspeed_sdc {
>
> spinlock_t lock;
> void __iomem *regs;
> + u32 max_tap_delay_ps;
> };
>
> struct aspeed_sdhci_tap_param {
> @@ -63,6 +64,7 @@ struct aspeed_sdhci_tap_desc {
> struct aspeed_sdhci_phase_desc {
> struct aspeed_sdhci_tap_desc in;
> struct aspeed_sdhci_tap_desc out;
> + u32 nr_taps;
> };
>
> struct aspeed_sdhci_pdata {
> @@ -158,43 +160,60 @@ aspeed_sdc_set_phase_taps(struct aspeed_sdc *sdc,
> }
>
> #define PICOSECONDS_PER_SECOND 1000000000000ULL
> -#define ASPEED_SDHCI_NR_TAPS 15
> -/* Measured value with *handwave* environmentals and static loading */
> -#define ASPEED_SDHCI_MAX_TAP_DELAY_PS 1253
> +#define ASPEED_SDHCI_MAX_TAPS 15
Why are we renaming this? It looks to cause a bit of noise in the diff.
> +
> static int aspeed_sdhci_phase_to_tap(struct device *dev, unsigned long rate_hz,
> - int phase_deg)
> + bool invert, int phase_deg, u32 nr_taps)
Hmm.
> {
> u64 phase_period_ps;
> u64 prop_delay_ps;
> u64 clk_period_ps;
> - unsigned int tap;
> - u8 inverted;
> + u32 tap = 0;
> + struct aspeed_sdc *sdc = dev_get_drvdata(dev->parent);
>
> - phase_deg %= 360;
> + if (sdc->max_tap_delay_ps == 0)
> + return 0;
I don't think just silently returning 0 here is the right thing to do.
What about -EINVAL, or printing a warning and using the old hard-coded
value?
>
> - if (phase_deg >= 180) {
> - inverted = ASPEED_SDHCI_TAP_PARAM_INVERT_CLK;
> - phase_deg -= 180;
> - dev_dbg(dev,
> - "Inverting clock to reduce phase correction from %d to %d degrees\n",
> - phase_deg + 180, phase_deg);
> - } else {
> - inverted = 0;
> + prop_delay_ps = sdc->max_tap_delay_ps / nr_taps;
> + clk_period_ps = div_u64(PICOSECONDS_PER_SECOND, (u64)rate_hz);
> +
> + /*
> + * For ast2600, if clock phase degree is negative, clock signal is
> + * output from falling edge first by default. Namely, clock signal
> + * is leading to data signal by 90 degrees at least.
> + */
Have I missed something about a asymmetric clock timings? Otherwise the
falling edge is 180 degrees away from the rising edge? I'm still not
clear on why 90 degrees is used here.
> + if (invert) {
> + if (phase_deg >= 90)
> + phase_deg -= 90;
> + else
> + phase_deg = 0;
Why are we throwing away information?
> }
>
> - prop_delay_ps = ASPEED_SDHCI_MAX_TAP_DELAY_PS / ASPEED_SDHCI_NR_TAPS;
> - clk_period_ps = div_u64(PICOSECONDS_PER_SECOND, (u64)rate_hz);
> phase_period_ps = div_u64((u64)phase_deg * clk_period_ps, 360ULL);
>
> - tap = div_u64(phase_period_ps, prop_delay_ps);
> - if (tap > ASPEED_SDHCI_NR_TAPS) {
> + /*
> + * The delay cell is non-uniform for eMMC controller.
> + * The time period of the first tap is two times of others.
> + */
> + if (nr_taps == 16 && phase_period_ps > prop_delay_ps * 2) {
> + phase_period_ps -= prop_delay_ps * 2;
> + tap++;
> + }
> +
> + tap += div_u64(phase_period_ps, prop_delay_ps);
> + if (tap > ASPEED_SDHCI_MAX_TAPS) {
> dev_dbg(dev,
> "Requested out of range phase tap %d for %d degrees of phase
> compensation at %luHz, clamping to tap %d\n",
> - tap, phase_deg, rate_hz, ASPEED_SDHCI_NR_TAPS);
> - tap = ASPEED_SDHCI_NR_TAPS;
> + tap, phase_deg, rate_hz, ASPEED_SDHCI_MAX_TAPS);
> + tap = ASPEED_SDHCI_MAX_TAPS;
> }
>
> - return inverted | tap;
> + if (invert) {
> + dev_info(dev, "invert the clock\n");
I prefer we drop this message
> + tap |= ASPEED_SDHCI_TAP_PARAM_INVERT_CLK;
> + }
> +
> + return tap;
> }
>
> static void
> @@ -202,13 +221,19 @@ aspeed_sdhci_phases_to_taps(struct device *dev,
> unsigned long rate,
> const struct mmc_clk_phase *phases,
> struct aspeed_sdhci_tap_param *taps)
> {
> + struct sdhci_host *host = dev->driver_data;
> + struct aspeed_sdhci *sdhci;
> +
> + sdhci = sdhci_pltfm_priv(sdhci_priv(host));
> taps->valid = phases->valid;
>
> if (!phases->valid)
> return;
>
> - taps->in = aspeed_sdhci_phase_to_tap(dev, rate, phases->in_deg);
> - taps->out = aspeed_sdhci_phase_to_tap(dev, rate, phases->out_deg);
> + taps->in = aspeed_sdhci_phase_to_tap(dev, rate, phases->inv_in_deg,
> + phases->in_deg, sdhci->phase_desc->nr_taps);
> + taps->out = aspeed_sdhci_phase_to_tap(dev, rate, phases->inv_out_deg,
> + phases->out_deg, sdhci->phase_desc->nr_taps);
> }
>
> static void
> @@ -230,8 +255,8 @@ aspeed_sdhci_configure_phase(struct sdhci_host
> *host, unsigned long rate)
> aspeed_sdc_set_phase_taps(sdhci->parent, sdhci->phase_desc, taps);
> dev_dbg(dev,
> "Using taps [%d, %d] for [%d, %d] degrees of phase correction at
> %luHz (%d)\n",
> - taps->in & ASPEED_SDHCI_NR_TAPS,
> - taps->out & ASPEED_SDHCI_NR_TAPS,
> + taps->in & ASPEED_SDHCI_MAX_TAPS,
> + taps->out & ASPEED_SDHCI_MAX_TAPS,
> params->in_deg, params->out_deg, rate, host->timing);
> }
>
> @@ -493,6 +518,7 @@ static const struct aspeed_sdhci_phase_desc
> ast2600_sdhci_phase[] = {
> .enable_mask = ASPEED_SDC_S0_PHASE_OUT_EN,
> .enable_value = 3,
> },
> + .nr_taps = 15,
> },
> /* SDHCI/Slot 1 */
> [1] = {
> @@ -506,6 +532,31 @@ static const struct aspeed_sdhci_phase_desc
> ast2600_sdhci_phase[] = {
> .enable_mask = ASPEED_SDC_S1_PHASE_OUT_EN,
> .enable_value = 3,
> },
> + .nr_taps = 15,
> + },
> +};
> +
> +static const struct aspeed_sdhci_phase_desc ast2600_emmc_phase[] = {
> + /* eMMC slot 0 */
> + [0] = {
> + .in = {
> + .tap_mask = ASPEED_SDC_S0_PHASE_IN,
> + .enable_mask = ASPEED_SDC_S0_PHASE_IN_EN,
> + .enable_value = 1,
> + },
> + .out = {
> + .tap_mask = ASPEED_SDC_S0_PHASE_OUT,
> + .enable_mask = ASPEED_SDC_S0_PHASE_OUT_EN,
> + .enable_value = 3,
> + },
> +
> + /*
> + * There are 15 taps recorded in AST2600 datasheet.
> + * But, actually, the time period of the first tap
> + * is two times of others. Thus, 16 tap is used to
> + * emulate this situation.
> + */
> + .nr_taps = 16,
I think this is a very indirect way to communicate the problem. The
only time we look at nr_taps is in a test that explicitly compensates
for the non-uniform delay. I think we should just have a boolean struct
member called 'non_uniform_delay' rather than 'nr_taps', as the number
of taps isn't what's changing. But also see the discussion below about
a potential aspeed,tap-delays property.
> },
> };
>
> @@ -515,10 +566,17 @@ static const struct aspeed_sdhci_pdata
> ast2600_sdhci_pdata = {
> .nr_phase_descs = ARRAY_SIZE(ast2600_sdhci_phase),
> };
>
> +static const struct aspeed_sdhci_pdata ast2600_emmc_pdata = {
> + .clk_div_start = 1,
> + .phase_desc = ast2600_emmc_phase,
> + .nr_phase_descs = ARRAY_SIZE(ast2600_emmc_phase),
> +};
> +
> static const struct of_device_id aspeed_sdhci_of_match[] = {
> { .compatible = "aspeed,ast2400-sdhci", .data = &ast2400_sdhci_pdata, },
> { .compatible = "aspeed,ast2500-sdhci", .data = &ast2400_sdhci_pdata, },
> { .compatible = "aspeed,ast2600-sdhci", .data = &ast2600_sdhci_pdata, },
> + { .compatible = "aspeed,ast2600-emmc", .data = &ast2600_emmc_pdata, },
This needs to be documented (and binding documentation patches need to
be the first patches in the series). Something further to consider is
whether we separate the compatibles or add e.g. an aspeed,tap-delays
property that specifies the specific delay of each logic element. This
might take the place of e.g. the max-tap-delay property?
Andrew
> { }
> };
>
> @@ -562,6 +620,11 @@ static int aspeed_sdc_probe(struct platform_device *pdev)
> goto err_clk;
> }
>
> + ret = of_property_read_u32(pdev->dev.of_node, "max-tap-delay",
> + &sdc->max_tap_delay_ps);
> + if (ret)
> + sdc->max_tap_delay_ps = 0;
> +
> dev_set_drvdata(&pdev->dev, sdc);
>
> parent = pdev->dev.of_node;
> --
> 2.17.1
More information about the openbmc
mailing list