[PATCH v2 1/3] ARM: dts: aspeed: mtjade: Add some gpios

[Quan Nguyen]

On 19/10/2021 13:46, Joel Stanley wrote:
> On Tue, 19 Oct 2021 at 06:02, Quan Nguyen <quan at os.amperecomputing.com> wrote:
>>
>> Add S0_SCP_AUTH_FAIL, S1_SCP_AUTH_FAIL gpios to indicates firmware
>> authentication fail on each socket.
> 
> These use the gpio-keys API to expose the GPIOs. I think OpenBMC is
> moving away from this abstraction, and instead reading the GPIOs with
> the gpio chardev interface.
> 
Thanks Joel for the review,
Yes, will switch to use gpio chardev interface and will remove these 
gpio-keys defined in next version

>>
>> Add gpio RTC_BAT_SEN_EN to enable RTC battery adc sensor.
>>
>> Add BMC_I2C4_O_EN gpio to go high at boot to enable access to I2C4 bus.
> 
> OpenBMC has started a process to document GPIOs that are exposed to
> userspace, initially so a common userspace can be used across
> machines. I like doing it for the additional reason that it provides
> consistency in the naming.
> 
> https://github.com/openbmc/docs/blob/master/designs/device-tree-gpio-naming.md
> 
> If you could take a look at that document and add your GPIOs where
> possible, and then update the device tree.
> 

There is on-going discussion about naming of the RTC voltage sensing 
enable gpio pin in [1], So I'd like to address this change later in 
separate patch when this is settled. Hence, I will remove this changes 
in next version.

[1] https://gerrit.openbmc-project.xyz/c/openbmc/docs/+/48018

About the BMC_I2C4_O_EN, this is needed as gpio-hog to make the i2c bus 
accessible at boot time so I will keep this in next version.
In fact, I'm still a bit of confuse if this pin needs a common name as 
it is just to enable the bus access and does not serve for any 
particular common purpose.

Thanks,
- Quan

>>
>> Signed-off-by: Quan Nguyen <quan at os.amperecomputing.com>
>> Signed-off-by: Thang Nguyen <thang at os.amperecomputing.com>
>> ---
>> v2:
>>    - None
>>
>>   .../arm/boot/dts/aspeed-bmc-ampere-mtjade.dts | 21 ++++++++++++++++++-
>>   1 file changed, 20 insertions(+), 1 deletion(-)
>>
>> diff --git a/arch/arm/boot/dts/aspeed-bmc-ampere-mtjade.dts b/arch/arm/boot/dts/aspeed-bmc-ampere-mtjade.dts
>> index 57b0c45a2298..3515d55bd312 100644
>> --- a/arch/arm/boot/dts/aspeed-bmc-ampere-mtjade.dts
>> +++ b/arch/arm/boot/dts/aspeed-bmc-ampere-mtjade.dts
>> @@ -86,6 +86,18 @@ S0_cpu_fault {
>>                          linux,code = <ASPEED_GPIO(J, 1)>;
>>                  };
>>
>> +               S0_scp_auth_fail {
>> +                       label = "S0_SCP_AUTH_FAIL";
>> +                       gpios = <&gpio ASPEED_GPIO(J, 2) GPIO_ACTIVE_LOW>;
>> +                       linux,code = <ASPEED_GPIO(J, 2)>;
>> +               };
>> +
>> +               S1_scp_auth_fail {
>> +                       label = "S1_SCP_AUTH_FAIL";
>> +                       gpios = <&gpio ASPEED_GPIO(Z, 5) GPIO_ACTIVE_LOW>;
>> +                       linux,code = <ASPEED_GPIO(Z, 5)>;
>> +               };
>> +
>>                  S1_overtemp {
>>                          label = "S1_OVERTEMP";
>>                          gpios = <&gpio ASPEED_GPIO(Z, 6) GPIO_ACTIVE_LOW>;
>> @@ -590,7 +602,7 @@ &gpio {
>>          /*Q0-Q7*/       "","","","","","UID_BUTTON","","",
>>          /*R0-R7*/       "","","BMC_EXT_HIGHTEMP_L","OCP_AUX_PWREN",
>>                          "OCP_MAIN_PWREN","RESET_BUTTON","","",
>> -       /*S0-S7*/       "","","","","","","","",
>> +       /*S0-S7*/       "","","","","RTC_BAT_SEN_EN","","","",
> 
> I suggest you create a proposal to call this one
> battery-voltage-read-enable. I know that some of the IBM machines
> intend to have this same GPIO.
> 
>>          /*T0-T7*/       "","","","","","","","",
>>          /*U0-U7*/       "","","","","","","","",
>>          /*V0-V7*/       "","","","","","","","",
>> @@ -604,4 +616,11 @@ &gpio {
>>                          "S1_BMC_DDR_ADR","","","","",
>>          /*AC0-AC7*/     "SYS_PWR_GD","","","","","BMC_READY","SLAVE_PRESENT_L",
>>                          "BMC_OCP_PG";
>> +
>> +       i2c4_o_en {
>> +               gpio-hog;
>> +               gpios = <ASPEED_GPIO(Y, 2) GPIO_ACTIVE_HIGH>;
>> +               output-high;
>> +               line-name = "BMC_I2C4_O_EN";
>> +       };
>>   };
>> --
>> 2.28.0
>>