[PATCH v3 4/4] i2c: aspeed: add DMA mode transfer support
Jae Hyun Yoo
jae.hyun.yoo at linux.intel.com
Wed Feb 17 05:27:35 AEDT 2021
This commit adds DMA mode transfer support.
Only AST2500 and later versions support DMA mode.
AST2500 has these restrictions:
- If one of these controllers is enabled
* UHCI host controller
* MCTP controller
I2C has to use buffer mode or byte mode instead
since these controllers run only in DMA mode and
I2C is sharing the same DMA H/W with them.
- If one of these controllers uses DMA mode, I2C
can't use DMA mode
* SD/eMMC
* Port80 snoop
Signed-off-by: Jae Hyun Yoo <jae.hyun.yoo at linux.intel.com>
---
Changes since v2:
- Refined SoC family dependent xfer mode configuration functions.
Changes since v1:
- Updated commit message and comments.
- Refined using abstract functions.
drivers/i2c/busses/i2c-aspeed.c | 257 ++++++++++++++++++++++++++------
1 file changed, 212 insertions(+), 45 deletions(-)
diff --git a/drivers/i2c/busses/i2c-aspeed.c b/drivers/i2c/busses/i2c-aspeed.c
index 343e621ff133..304d08011ca7 100644
--- a/drivers/i2c/busses/i2c-aspeed.c
+++ b/drivers/i2c/busses/i2c-aspeed.c
@@ -10,6 +10,8 @@
#include <linux/bitfield.h>
#include <linux/clk.h>
#include <linux/completion.h>
+#include <linux/dma-mapping.h>
+#include <linux/dmapool.h>
#include <linux/err.h>
#include <linux/errno.h>
#include <linux/i2c.h>
@@ -47,6 +49,8 @@
#define ASPEED_I2C_DEV_ADDR_REG 0x18
#define ASPEED_I2C_BUF_CTRL_REG 0x1c
#define ASPEED_I2C_BYTE_BUF_REG 0x20
+#define ASPEED_I2C_DMA_ADDR_REG 0x24
+#define ASPEED_I2C_DMA_LEN_REG 0x28
/* Device Register Definition */
/* 0x00 : I2CD Function Control Register */
@@ -111,6 +115,8 @@
#define ASPEED_I2CD_BUS_RECOVER_CMD BIT(11)
/* Command Bit */
+#define ASPEED_I2CD_RX_DMA_ENABLE BIT(9)
+#define ASPEED_I2CD_TX_DMA_ENABLE BIT(8)
#define ASPEED_I2CD_RX_BUFF_ENABLE BIT(7)
#define ASPEED_I2CD_TX_BUFF_ENABLE BIT(6)
#define ASPEED_I2CD_M_STOP_CMD BIT(5)
@@ -136,6 +142,14 @@
#define ASPEED_I2CD_BUF_TX_COUNT_MASK GENMASK(15, 8)
#define ASPEED_I2CD_BUF_OFFSET_MASK GENMASK(5, 0)
+/* 0x24 : I2CD DMA Mode Buffer Address Register */
+#define ASPEED_I2CD_DMA_ADDR_MASK GENMASK(31, 2)
+#define ASPEED_I2CD_DMA_ALIGN 4
+
+/* 0x28 : I2CD DMA Transfer Length Register */
+#define ASPEED_I2CD_DMA_LEN_SHIFT 0
+#define ASPEED_I2CD_DMA_LEN_MASK GENMASK(11, 0)
+
enum aspeed_i2c_master_state {
ASPEED_I2C_MASTER_INACTIVE,
ASPEED_I2C_MASTER_PENDING,
@@ -161,6 +175,7 @@ struct aspeed_i2c_config {
u32 (*get_clk_reg_val)(struct device *dev, u32 divisor);
int (*enable_sram)(void);
int (*set_buf_xfer_mode)(struct device *dev);
+ int (*set_dma_xfer_mode)(struct device *dev);
};
struct aspeed_i2c_bus {
@@ -190,6 +205,12 @@ struct aspeed_i2c_bus {
void __iomem *buf_base;
u8 buf_offset;
u8 buf_page;
+ /* DMA mode */
+ struct dma_pool *dma_pool;
+ dma_addr_t dma_handle;
+ u8 *dma_buf;
+ size_t dma_len;
+ /* Buffer/DMA mode */
size_t buf_size;
#if IS_ENABLED(CONFIG_I2C_SLAVE)
struct i2c_client *slave;
@@ -272,9 +293,13 @@ static inline void
aspeed_i2c_slave_handle_rx_done(struct aspeed_i2c_bus *bus, u32 irq_status,
u8 *value)
{
- if (bus->buf_base &&
+ if (bus->dma_buf &&
bus->slave_state == ASPEED_I2C_SLAVE_WRITE_RECEIVED &&
!(irq_status & ASPEED_I2CD_INTR_NORMAL_STOP))
+ *value = bus->dma_buf[0];
+ else if (bus->buf_base &&
+ bus->slave_state == ASPEED_I2C_SLAVE_WRITE_RECEIVED &&
+ !(irq_status & ASPEED_I2CD_INTR_NORMAL_STOP))
*value = readb(bus->buf_base);
else
*value = readl(bus->base + ASPEED_I2C_BYTE_BUF_REG) >> 8;
@@ -288,7 +313,18 @@ aspeed_i2c_slave_handle_normal_stop(struct aspeed_i2c_bus *bus, u32 irq_status,
if (bus->slave_state == ASPEED_I2C_SLAVE_WRITE_RECEIVED &&
irq_status & ASPEED_I2CD_INTR_RX_DONE) {
- if (bus->buf_base) {
+ if (bus->dma_buf) {
+ len = bus->buf_size -
+ FIELD_GET(ASPEED_I2CD_DMA_LEN_MASK,
+ readl(bus->base +
+ ASPEED_I2C_DMA_LEN_REG));
+ for (i = 0; i < len; i++) {
+ *value = bus->dma_buf[i];
+ i2c_slave_event(bus->slave,
+ I2C_SLAVE_WRITE_RECEIVED,
+ value);
+ }
+ } else if (bus->buf_base) {
len = FIELD_GET(ASPEED_I2CD_BUF_RX_COUNT_MASK,
readl(bus->base +
ASPEED_I2C_BUF_CTRL_REG));
@@ -305,7 +341,14 @@ aspeed_i2c_slave_handle_normal_stop(struct aspeed_i2c_bus *bus, u32 irq_status,
static inline void
aspeed_i2c_slave_handle_write_requested(struct aspeed_i2c_bus *bus, u8 *value)
{
- if (bus->buf_base) {
+ if (bus->dma_buf) {
+ writel(bus->dma_handle & ASPEED_I2CD_DMA_ADDR_MASK,
+ bus->base + ASPEED_I2C_DMA_ADDR_REG);
+ writel(FIELD_PREP(ASPEED_I2CD_DMA_LEN_MASK, bus->buf_size),
+ bus->base + ASPEED_I2C_DMA_LEN_REG);
+ writel(ASPEED_I2CD_RX_DMA_ENABLE,
+ bus->base + ASPEED_I2C_CMD_REG);
+ } else if (bus->buf_base) {
writel(FIELD_PREP(ASPEED_I2CD_BUF_RX_SIZE_MASK,
bus->buf_size - 1) |
FIELD_PREP(ASPEED_I2CD_BUF_OFFSET_MASK,
@@ -321,7 +364,23 @@ aspeed_i2c_slave_handle_write_received(struct aspeed_i2c_bus *bus, u8 *value)
{
int i, len;
- if (bus->buf_base) {
+ if (bus->dma_buf) {
+ len = bus->buf_size -
+ FIELD_GET(ASPEED_I2CD_DMA_LEN_MASK,
+ readl(bus->base +
+ ASPEED_I2C_DMA_LEN_REG));
+ for (i = 1; i < len; i++) {
+ *value = bus->dma_buf[i];
+ i2c_slave_event(bus->slave, I2C_SLAVE_WRITE_RECEIVED,
+ value);
+ }
+ writel(bus->dma_handle & ASPEED_I2CD_DMA_ADDR_MASK,
+ bus->base + ASPEED_I2C_DMA_ADDR_REG);
+ writel(FIELD_PREP(ASPEED_I2CD_DMA_LEN_MASK, bus->buf_size),
+ bus->base + ASPEED_I2C_DMA_LEN_REG);
+ writel(ASPEED_I2CD_RX_DMA_ENABLE,
+ bus->base + ASPEED_I2C_CMD_REG);
+ } else if (bus->buf_base) {
len = FIELD_GET(ASPEED_I2CD_BUF_RX_COUNT_MASK,
readl(bus->base +
ASPEED_I2C_BUF_CTRL_REG));
@@ -451,7 +510,15 @@ aspeed_i2c_prepare_rx_buf(struct aspeed_i2c_bus *bus, struct i2c_msg *msg)
command |= ASPEED_I2CD_M_S_RX_CMD_LAST;
}
- if (bus->buf_base) {
+ if (bus->dma_buf) {
+ command |= ASPEED_I2CD_RX_DMA_ENABLE;
+
+ writel(bus->dma_handle & ASPEED_I2CD_DMA_ADDR_MASK,
+ bus->base + ASPEED_I2C_DMA_ADDR_REG);
+ writel(FIELD_PREP(ASPEED_I2CD_DMA_LEN_MASK, len),
+ bus->base + ASPEED_I2C_DMA_LEN_REG);
+ bus->dma_len = len;
+ } else {
command |= ASPEED_I2CD_RX_BUFF_ENABLE;
writel(FIELD_PREP(ASPEED_I2CD_BUF_RX_SIZE_MASK, len - 1) |
@@ -474,7 +541,18 @@ aspeed_i2c_prepare_tx_buf(struct aspeed_i2c_bus *bus, struct i2c_msg *msg)
else
len = msg->len + 1;
- if (bus->buf_base) {
+ if (bus->dma_buf) {
+ command |= ASPEED_I2CD_TX_DMA_ENABLE;
+
+ bus->dma_buf[0] = slave_addr;
+ memcpy(bus->dma_buf + 1, msg->buf, len);
+
+ writel(bus->dma_handle & ASPEED_I2CD_DMA_ADDR_MASK,
+ bus->base + ASPEED_I2C_DMA_ADDR_REG);
+ writel(FIELD_PREP(ASPEED_I2CD_DMA_LEN_MASK, len),
+ bus->base + ASPEED_I2C_DMA_LEN_REG);
+ bus->dma_len = len;
+ } else {
u8 wbuf[4];
int i;
@@ -527,18 +605,19 @@ static void aspeed_i2c_do_start(struct aspeed_i2c_bus *bus)
if (msg->flags & I2C_M_RD) {
command |= ASPEED_I2CD_M_RX_CMD;
if (!(msg->flags & I2C_M_RECV_LEN)) {
- if (msg->len && bus->buf_base)
+ if (msg->len && (bus->dma_buf || bus->buf_base))
command |= aspeed_i2c_prepare_rx_buf(bus, msg);
/* Need to let the hardware know to NACK after RX. */
if (msg->len <= 1)
command |= ASPEED_I2CD_M_S_RX_CMD_LAST;
}
- } else if (msg->len && bus->buf_base) {
+ } else if (msg->len && (bus->dma_buf || bus->buf_base)) {
command |= aspeed_i2c_prepare_tx_buf(bus, msg);
}
- if (!(command & ASPEED_I2CD_TX_BUFF_ENABLE))
+ if (!(command & (ASPEED_I2CD_TX_BUFF_ENABLE |
+ ASPEED_I2CD_TX_DMA_ENABLE)))
writel(i2c_8bit_addr_from_msg(msg),
bus->base + ASPEED_I2C_BYTE_BUF_REG);
writel(command, bus->base + ASPEED_I2C_CMD_REG);
@@ -581,38 +660,51 @@ aspeed_i2c_master_handle_tx_first(struct aspeed_i2c_bus *bus,
{
u32 command = 0;
- if (bus->buf_base) {
- u8 wbuf[4];
+ if (bus->dma_buf || bus->buf_base) {
int len;
- int i;
if (msg->len - bus->buf_index > bus->buf_size)
len = bus->buf_size;
else
len = msg->len - bus->buf_index;
- command |= ASPEED_I2CD_TX_BUFF_ENABLE;
+ if (bus->dma_buf) {
+ command |= ASPEED_I2CD_TX_DMA_ENABLE;
- if (msg->len - bus->buf_index > bus->buf_size)
- len = bus->buf_size;
- else
- len = msg->len - bus->buf_index;
+ memcpy(bus->dma_buf, msg->buf + bus->buf_index, len);
- for (i = 0; i < len; i++) {
- wbuf[i % 4] = msg->buf[bus->buf_index + i];
- if (i % 4 == 3)
+ writel(bus->dma_handle & ASPEED_I2CD_DMA_ADDR_MASK,
+ bus->base + ASPEED_I2C_DMA_ADDR_REG);
+ writel(FIELD_PREP(ASPEED_I2CD_DMA_LEN_MASK, len),
+ bus->base + ASPEED_I2C_DMA_LEN_REG);
+ bus->dma_len = len;
+ } else {
+ u8 wbuf[4];
+ int i;
+
+ command |= ASPEED_I2CD_TX_BUFF_ENABLE;
+
+ if (msg->len - bus->buf_index > bus->buf_size)
+ len = bus->buf_size;
+ else
+ len = msg->len - bus->buf_index;
+
+ for (i = 0; i < len; i++) {
+ wbuf[i % 4] = msg->buf[bus->buf_index + i];
+ if (i % 4 == 3)
+ writel(*(u32 *)wbuf,
+ bus->buf_base + i - 3);
+ }
+ if (--i % 4 != 3)
writel(*(u32 *)wbuf,
- bus->buf_base + i - 3);
- }
- if (--i % 4 != 3)
- writel(*(u32 *)wbuf,
- bus->buf_base + i - (i % 4));
+ bus->buf_base + i - (i % 4));
- writel(FIELD_PREP(ASPEED_I2CD_BUF_TX_COUNT_MASK,
- len - 1) |
- FIELD_PREP(ASPEED_I2CD_BUF_OFFSET_MASK,
- bus->buf_offset),
- bus->base + ASPEED_I2C_BUF_CTRL_REG);
+ writel(FIELD_PREP(ASPEED_I2CD_BUF_TX_COUNT_MASK,
+ len - 1) |
+ FIELD_PREP(ASPEED_I2CD_BUF_OFFSET_MASK,
+ bus->buf_offset),
+ bus->base + ASPEED_I2C_BUF_CTRL_REG);
+ }
bus->buf_index += len;
} else {
@@ -629,7 +721,14 @@ aspeed_i2c_master_handle_rx(struct aspeed_i2c_bus *bus, struct i2c_msg *msg)
u8 recv_byte;
int len;
- if (bus->buf_base) {
+ if (bus->dma_buf) {
+ len = bus->dma_len -
+ FIELD_GET(ASPEED_I2CD_DMA_LEN_MASK,
+ readl(bus->base + ASPEED_I2C_DMA_LEN_REG));
+
+ memcpy(msg->buf + bus->buf_index, bus->dma_buf, len);
+ bus->buf_index += len;
+ } else if (bus->buf_base) {
len = FIELD_GET(ASPEED_I2CD_BUF_RX_COUNT_MASK,
readl(bus->base + ASPEED_I2C_BUF_CTRL_REG));
memcpy_fromio(msg->buf + bus->buf_index, bus->buf_base, len);
@@ -646,7 +745,7 @@ aspeed_i2c_master_handle_rx_next(struct aspeed_i2c_bus *bus,
{
u32 command = 0;
- if (bus->buf_base) {
+ if (bus->dma_buf || bus->buf_base) {
int len;
if (msg->len - bus->buf_index > bus->buf_size) {
@@ -656,14 +755,24 @@ aspeed_i2c_master_handle_rx_next(struct aspeed_i2c_bus *bus,
command |= ASPEED_I2CD_M_S_RX_CMD_LAST;
}
- command |= ASPEED_I2CD_RX_BUFF_ENABLE;
+ if (bus->dma_buf) {
+ command |= ASPEED_I2CD_RX_DMA_ENABLE;
- writel(FIELD_PREP(ASPEED_I2CD_BUF_RX_SIZE_MASK,
- len - 1) |
- FIELD_PREP(ASPEED_I2CD_BUF_TX_COUNT_MASK, 0) |
- FIELD_PREP(ASPEED_I2CD_BUF_OFFSET_MASK,
- bus->buf_offset),
- bus->base + ASPEED_I2C_BUF_CTRL_REG);
+ writel(bus->dma_handle & ASPEED_I2CD_DMA_ADDR_MASK,
+ bus->base + ASPEED_I2C_DMA_ADDR_REG);
+ writel(FIELD_PREP(ASPEED_I2CD_DMA_LEN_MASK, len),
+ bus->base + ASPEED_I2C_DMA_LEN_REG);
+ bus->dma_len = len;
+ } else {
+ command |= ASPEED_I2CD_RX_BUFF_ENABLE;
+
+ writel(FIELD_PREP(ASPEED_I2CD_BUF_RX_SIZE_MASK,
+ len - 1) |
+ FIELD_PREP(ASPEED_I2CD_BUF_TX_COUNT_MASK, 0) |
+ FIELD_PREP(ASPEED_I2CD_BUF_OFFSET_MASK,
+ bus->buf_offset),
+ bus->base + ASPEED_I2C_BUF_CTRL_REG);
+ }
} else {
if (bus->buf_index + 1 == msg->len)
command |= ASPEED_I2CD_M_S_RX_CMD_LAST;
@@ -1283,22 +1392,63 @@ static int aspeed_i2c_25xx_set_buf_xfer_mode(struct device *dev)
return bus->buf_size ? 0 : -EINVAL;
}
+static int aspeed_i2c_24xx_set_dma_xfer_mode(struct device *dev)
+{
+ /* AST24xx doesn't support DMA mode */
+
+ return -EBADR;
+}
+
+static int aspeed_i2c_25xx_set_dma_xfer_mode(struct device *dev)
+{
+ struct platform_device *pdev = to_platform_device(dev);
+ struct aspeed_i2c_bus *bus = platform_get_drvdata(pdev);
+ int ret;
+
+ ret = dma_set_mask(&pdev->dev, DMA_BIT_MASK(32));
+ if (!ret) {
+ bus->buf_size = ASPEED_I2CD_DMA_LEN_MASK >>
+ ASPEED_I2CD_DMA_LEN_SHIFT;
+ bus->dma_pool = dma_pool_create("i2c-aspeed",
+ &pdev->dev,
+ bus->buf_size,
+ ASPEED_I2CD_DMA_ALIGN,
+ 0);
+ if (bus->dma_pool)
+ bus->dma_buf = dma_pool_alloc(bus->dma_pool,
+ GFP_KERNEL,
+ &bus->dma_handle);
+
+ if (!bus->dma_buf) {
+ ret = -ENOMEM;
+ bus->buf_size = 0;
+ dev_dbg(&pdev->dev, "Cannot allocate DMA buffer\n");
+ dma_pool_destroy(bus->dma_pool);
+ }
+ }
+
+ return ret;
+}
+
static const struct aspeed_i2c_config ast24xx_config = {
.get_clk_reg_val = aspeed_i2c_24xx_get_clk_reg_val,
.enable_sram = aspeed_i2c_24xx_enable_sram,
.set_buf_xfer_mode = aspeed_i2c_24xx_set_buf_xfer_mode,
+ .set_dma_xfer_mode = aspeed_i2c_24xx_set_dma_xfer_mode,
};
static const struct aspeed_i2c_config ast25xx_config = {
.get_clk_reg_val = aspeed_i2c_25xx_get_clk_reg_val,
.enable_sram = aspeed_i2c_25xx_enable_sram,
.set_buf_xfer_mode = aspeed_i2c_25xx_set_buf_xfer_mode,
+ .set_dma_xfer_mode = aspeed_i2c_25xx_set_dma_xfer_mode,
};
static const struct aspeed_i2c_config ast26xx_config = {
.get_clk_reg_val = aspeed_i2c_25xx_get_clk_reg_val,
.enable_sram = aspeed_i2c_24xx_enable_sram,
.set_buf_xfer_mode = aspeed_i2c_25xx_set_buf_xfer_mode,
+ .set_dma_xfer_mode = aspeed_i2c_25xx_set_dma_xfer_mode,
};
static const struct of_device_id aspeed_i2c_bus_of_table[] = {
@@ -1320,8 +1470,12 @@ static void aspeed_i2c_set_xfer_mode(struct aspeed_i2c_bus *bus)
return;
ret = bus->config->enable_sram();
- if (!ret && !strncasecmp(mode, "buf", 3))
- ret = bus->config->set_buf_xfer_mode(bus->dev);
+ if (!ret) {
+ if (!strncasecmp(mode, "buf", 3))
+ ret = bus->config->set_buf_xfer_mode(bus->dev);
+ else if (!strncasecmp(mode, "dma", 3))
+ ret = bus->config->set_dma_xfer_mode(bus->dev);
+ }
if (ret)
dev_dbg(&pdev->dev, "Use default (byte) xfer mode\n");
@@ -1396,22 +1550,31 @@ static int aspeed_i2c_probe_bus(struct platform_device *pdev)
*/
ret = aspeed_i2c_init(bus, pdev);
if (ret < 0)
- return ret;
+ goto out_free_dma_buf;
irq = irq_of_parse_and_map(pdev->dev.of_node, 0);
ret = devm_request_irq(&pdev->dev, irq, aspeed_i2c_bus_irq,
0, dev_name(&pdev->dev), bus);
if (ret < 0)
- return ret;
+ goto out_free_dma_buf;
ret = i2c_add_adapter(&bus->adap);
if (ret < 0)
- return ret;
+ goto out_free_dma_buf;
dev_info(bus->dev, "i2c bus %d registered (%s mode), irq %d\n",
- bus->adap.nr, bus->buf_base ? "buf" : "byte", irq);
+ bus->adap.nr, bus->dma_buf ? "dma" :
+ bus->buf_base ? "buf" : "byte",
+ irq);
return 0;
+
+out_free_dma_buf:
+ if (bus->dma_buf)
+ dma_pool_free(bus->dma_pool, bus->dma_buf, bus->dma_handle);
+ dma_pool_destroy(bus->dma_pool);
+
+ return ret;
}
static int aspeed_i2c_remove_bus(struct platform_device *pdev)
@@ -1429,6 +1592,10 @@ static int aspeed_i2c_remove_bus(struct platform_device *pdev)
reset_control_assert(bus->rst);
+ if (bus->dma_buf)
+ dma_pool_free(bus->dma_pool, bus->dma_buf, bus->dma_handle);
+ dma_pool_destroy(bus->dma_pool);
+
i2c_del_adapter(&bus->adap);
return 0;
--
2.17.1
More information about the openbmc
mailing list