[PATCH v2 07/15] peci: Add peci-aspeed controller driver
Winiarska, Iwona
iwona.winiarska at intel.com
Fri Aug 27 09:54:56 AEST 2021
On Wed, 2021-08-25 at 18:35 -0700, Dan Williams wrote:
> On Tue, Aug 3, 2021 at 4:35 AM Iwona Winiarska
> <iwona.winiarska at intel.com> wrote:
> >
> > From: Jae Hyun Yoo <jae.hyun.yoo at linux.intel.com>
> >
> > ASPEED AST24xx/AST25xx/AST26xx SoCs supports the PECI electrical
> > interface (a.k.a PECI wire).
>
> Maybe a one sentence blurb here and in the Kconfig reminding people
> why they should care if they have a PECI driver or not?
Ok, I'll expand it a bit.
>
> >
> > Signed-off-by: Jae Hyun Yoo <jae.hyun.yoo at linux.intel.com>
> > Co-developed-by: Iwona Winiarska <iwona.winiarska at intel.com>
> > Signed-off-by: Iwona Winiarska <iwona.winiarska at intel.com>
> > Reviewed-by: Pierre-Louis Bossart <pierre-louis.bossart at linux.intel.com>
> > ---
> > MAINTAINERS | 9 +
> > drivers/peci/Kconfig | 6 +
> > drivers/peci/Makefile | 3 +
> > drivers/peci/controller/Kconfig | 16 +
> > drivers/peci/controller/Makefile | 3 +
> > drivers/peci/controller/peci-aspeed.c | 445 ++++++++++++++++++++++++++
> > 6 files changed, 482 insertions(+)
> > create mode 100644 drivers/peci/controller/Kconfig
> > create mode 100644 drivers/peci/controller/Makefile
> > create mode 100644 drivers/peci/controller/peci-aspeed.c
> >
> > diff --git a/MAINTAINERS b/MAINTAINERS
> > index d411974aaa5e..6e9d53ff68ab 100644
> > --- a/MAINTAINERS
> > +++ b/MAINTAINERS
> > @@ -2866,6 +2866,15 @@ S: Maintained
> > F: Documentation/hwmon/asc7621.rst
> > F: drivers/hwmon/asc7621.c
> >
> > +ASPEED PECI CONTROLLER
> > +M: Iwona Winiarska <iwona.winiarska at intel.com>
> > +M: Jae Hyun Yoo <jae.hyun.yoo at linux.intel.com>
> > +L: linux-aspeed at lists.ozlabs.org (moderated for non-subscribers)
> > +L: openbmc at lists.ozlabs.org (moderated for non-subscribers)
> > +S: Supported
> > +F: Documentation/devicetree/bindings/peci/peci-aspeed.yaml
> > +F: drivers/peci/controller/peci-aspeed.c
> > +
> > ASPEED PINCTRL DRIVERS
> > M: Andrew Jeffery <andrew at aj.id.au>
> > L: linux-aspeed at lists.ozlabs.org (moderated for non-subscribers)
> > diff --git a/drivers/peci/Kconfig b/drivers/peci/Kconfig
> > index 71a4ad81225a..99279df97a78 100644
> > --- a/drivers/peci/Kconfig
> > +++ b/drivers/peci/Kconfig
> > @@ -13,3 +13,9 @@ menuconfig PECI
> >
> > This support is also available as a module. If so, the module
> > will be called peci.
> > +
> > +if PECI
> > +
> > +source "drivers/peci/controller/Kconfig"
> > +
> > +endif # PECI
> > diff --git a/drivers/peci/Makefile b/drivers/peci/Makefile
> > index e789a354e842..926d8df15cbd 100644
> > --- a/drivers/peci/Makefile
> > +++ b/drivers/peci/Makefile
> > @@ -3,3 +3,6 @@
> > # Core functionality
> > peci-y := core.o
> > obj-$(CONFIG_PECI) += peci.o
> > +
> > +# Hardware specific bus drivers
> > +obj-y += controller/
> > diff --git a/drivers/peci/controller/Kconfig
> > b/drivers/peci/controller/Kconfig
> > new file mode 100644
> > index 000000000000..6d48df08db1c
> > --- /dev/null
> > +++ b/drivers/peci/controller/Kconfig
> > @@ -0,0 +1,16 @@
> > +# SPDX-License-Identifier: GPL-2.0-only
> > +
> > +config PECI_ASPEED
> > + tristate "ASPEED PECI support"
> > + depends on ARCH_ASPEED || COMPILE_TEST
> > + depends on OF
> > + depends on HAS_IOMEM
> > + help
> > + This option enables PECI controller driver for ASPEED AST2400,
> > + AST2500 and AST2600 SoCs.
> > +
> > + Say Y here if your system runs on ASPEED SoC and you are using it
> > + as BMC for Intel platform.
> > +
> > + This driver can also be built as a module. If so, the module will
> > + be called peci-aspeed.
> > diff --git a/drivers/peci/controller/Makefile
> > b/drivers/peci/controller/Makefile
> > new file mode 100644
> > index 000000000000..022c28ef1bf0
> > --- /dev/null
> > +++ b/drivers/peci/controller/Makefile
> > @@ -0,0 +1,3 @@
> > +# SPDX-License-Identifier: GPL-2.0-only
> > +
> > +obj-$(CONFIG_PECI_ASPEED) += peci-aspeed.o
> > diff --git a/drivers/peci/controller/peci-aspeed.c
> > b/drivers/peci/controller/peci-aspeed.c
> > new file mode 100644
> > index 000000000000..1d708c983749
> > --- /dev/null
> > +++ b/drivers/peci/controller/peci-aspeed.c
> > @@ -0,0 +1,445 @@
> > +// SPDX-License-Identifier: GPL-2.0-only
> > +// Copyright (C) 2012-2017 ASPEED Technology Inc.
> > +// Copyright (c) 2018-2021 Intel Corporation
>
> Why different copyright capitalization?
I'll make them consistent.
>
> > +
> > +#include <linux/bitfield.h>
> > +#include <linux/clk.h>
> > +#include <linux/delay.h>
> > +#include <linux/interrupt.h>
> > +#include <linux/io.h>
> > +#include <linux/iopoll.h>
> > +#include <linux/jiffies.h>
> > +#include <linux/module.h>
> > +#include <linux/of.h>
> > +#include <linux/peci.h>
> > +#include <linux/platform_device.h>
> > +#include <linux/reset.h>
> > +
> > +#include <asm/unaligned.h>
>
> Why is this included?
Leftover - I'll remove it.
>
> > +
> > +/* ASPEED PECI Registers */
> > +/* Control Register */
> > +#define ASPEED_PECI_CTRL 0x00
> > +#define ASPEED_PECI_CTRL_SAMPLING_MASK GENMASK(19, 16)
> > +#define ASPEED_PECI_CTRL_RD_MODE_MASK GENMASK(13, 12)
> > +#define ASPEED_PECI_CTRL_RD_MODE_DBG BIT(13)
> > +#define ASPEED_PECI_CTRL_RD_MODE_COUNT BIT(12)
> > +#define ASPEED_PECI_CTRL_CLK_SOURCE BIT(11)
> > +#define ASPEED_PECI_CTRL_CLK_DIV_MASK GENMASK(10, 8)
> > +#define ASPEED_PECI_CTRL_INVERT_OUT BIT(7)
> > +#define ASPEED_PECI_CTRL_INVERT_IN BIT(6)
> > +#define ASPEED_PECI_CTRL_BUS_CONTENTION_EN BIT(5)
> > +#define ASPEED_PECI_CTRL_PECI_EN BIT(4)
> > +#define ASPEED_PECI_CTRL_PECI_CLK_EN BIT(0)
> > +
> > +/* Timing Negotiation Register */
> > +#define ASPEED_PECI_TIMING_NEGOTIATION 0x04
> > +#define ASPEED_PECI_T_NEGO_MSG_MASK GENMASK(15, 8)
> > +#define ASPEED_PECI_T_NEGO_ADDR_MASK GENMASK(7, 0)
> > +
> > +/* Command Register */
> > +#define ASPEED_PECI_CMD 0x08
> > +#define ASPEED_PECI_CMD_PIN_MONITORING BIT(31)
> > +#define ASPEED_PECI_CMD_STS_MASK GENMASK(27, 24)
> > +#define ASPEED_PECI_CMD_STS_ADDR_T_NEGO 0x3
> > +#define ASPEED_PECI_CMD_IDLE_MASK \
> > + (ASPEED_PECI_CMD_STS_MASK | ASPEED_PECI_CMD_PIN_MONITORING)
> > +#define ASPEED_PECI_CMD_FIRE BIT(0)
> > +
> > +/* Read/Write Length Register */
> > +#define ASPEED_PECI_RW_LENGTH 0x0c
> > +#define ASPEED_PECI_AW_FCS_EN BIT(31)
> > +#define ASPEED_PECI_RD_LEN_MASK GENMASK(23, 16)
> > +#define ASPEED_PECI_WR_LEN_MASK GENMASK(15, 8)
> > +#define ASPEED_PECI_TARGET_ADDR_MASK GENMASK(7, 0)
> > +
> > +/* Expected FCS Data Register */
> > +#define ASPEED_PECI_EXPECTED_FCS 0x10
> > +#define ASPEED_PECI_EXPECTED_RD_FCS_MASK GENMASK(23, 16)
> > +#define ASPEED_PECI_EXPECTED_AW_FCS_AUTO_MASK GENMASK(15, 8)
> > +#define ASPEED_PECI_EXPECTED_WR_FCS_MASK GENMASK(7, 0)
> > +
> > +/* Captured FCS Data Register */
> > +#define ASPEED_PECI_CAPTURED_FCS 0x14
> > +#define ASPEED_PECI_CAPTURED_RD_FCS_MASK GENMASK(23, 16)
> > +#define ASPEED_PECI_CAPTURED_WR_FCS_MASK GENMASK(7, 0)
> > +
> > +/* Interrupt Register */
> > +#define ASPEED_PECI_INT_CTRL 0x18
> > +#define ASPEED_PECI_TIMING_NEGO_SEL_MASK GENMASK(31, 30)
> > +#define ASPEED_PECI_1ST_BIT_OF_ADDR_NEGO 0
> > +#define ASPEED_PECI_2ND_BIT_OF_ADDR_NEGO 1
> > +#define ASPEED_PECI_MESSAGE_NEGO 2
> > +#define ASPEED_PECI_INT_MASK GENMASK(4, 0)
> > +#define ASPEED_PECI_INT_BUS_TIMEOUT BIT(4)
> > +#define ASPEED_PECI_INT_BUS_CONTENTION BIT(3)
> > +#define ASPEED_PECI_INT_WR_FCS_BAD BIT(2)
> > +#define ASPEED_PECI_INT_WR_FCS_ABORT BIT(1)
> > +#define ASPEED_PECI_INT_CMD_DONE BIT(0)
> > +
> > +/* Interrupt Status Register */
> > +#define ASPEED_PECI_INT_STS 0x1c
> > +#define ASPEED_PECI_INT_TIMING_RESULT_MASK GENMASK(29, 16)
> > + /* bits[4..0]: Same bit fields in the 'Interrupt Register' */
> > +
> > +/* Rx/Tx Data Buffer Registers */
> > +#define ASPEED_PECI_WR_DATA0 0x20
> > +#define ASPEED_PECI_WR_DATA1 0x24
> > +#define ASPEED_PECI_WR_DATA2 0x28
> > +#define ASPEED_PECI_WR_DATA3 0x2c
> > +#define ASPEED_PECI_RD_DATA0 0x30
> > +#define ASPEED_PECI_RD_DATA1 0x34
> > +#define ASPEED_PECI_RD_DATA2 0x38
> > +#define ASPEED_PECI_RD_DATA3 0x3c
> > +#define ASPEED_PECI_WR_DATA4 0x40
> > +#define ASPEED_PECI_WR_DATA5 0x44
> > +#define ASPEED_PECI_WR_DATA6 0x48
> > +#define ASPEED_PECI_WR_DATA7 0x4c
> > +#define ASPEED_PECI_RD_DATA4 0x50
> > +#define ASPEED_PECI_RD_DATA5 0x54
> > +#define ASPEED_PECI_RD_DATA6 0x58
> > +#define ASPEED_PECI_RD_DATA7 0x5c
> > +#define ASPEED_PECI_DATA_BUF_SIZE_MAX 32
> > +
> > +/* Timing Negotiation */
> > +#define ASPEED_PECI_RD_SAMPLING_POINT_DEFAULT 8
> > +#define ASPEED_PECI_RD_SAMPLING_POINT_MAX (BIT(4) - 1)
> > +#define ASPEED_PECI_CLK_DIV_DEFAULT 0
> > +#define ASPEED_PECI_CLK_DIV_MAX (BIT(3) - 1)
> > +#define ASPEED_PECI_MSG_TIMING_DEFAULT 1
> > +#define ASPEED_PECI_MSG_TIMING_MAX (BIT(8) - 1)
> > +#define ASPEED_PECI_ADDR_TIMING_DEFAULT 1
> > +#define ASPEED_PECI_ADDR_TIMING_MAX (BIT(8) - 1)
> > +
> > +/* Timeout */
> > +#define ASPEED_PECI_IDLE_CHECK_TIMEOUT_US (50 * USEC_PER_MSEC)
> > +#define ASPEED_PECI_IDLE_CHECK_INTERVAL_US (10 * USEC_PER_MSEC)
> > +#define ASPEED_PECI_CMD_TIMEOUT_MS_DEFAULT (1000)
> > +#define ASPEED_PECI_CMD_TIMEOUT_MS_MAX (1000)
> > +
> > +struct aspeed_peci {
> > + struct peci_controller *controller;
> > + struct device *dev;
> > + void __iomem *base;
> > + struct clk *clk;
> > + struct reset_control *rst;
> > + int irq;
> > + spinlock_t lock; /* to sync completion status handling */
> > + struct completion xfer_complete;
> > + u32 status;
> > + u32 cmd_timeout_ms;
> > + u32 msg_timing;
> > + u32 addr_timing;
> > + u32 rd_sampling_point;
> > + u32 clk_div;
> > +};
> > +
> > +static void aspeed_peci_init_regs(struct aspeed_peci *priv)
> > +{
> > + u32 val;
> > +
> > + val = FIELD_PREP(ASPEED_PECI_CTRL_CLK_DIV_MASK,
> > ASPEED_PECI_CLK_DIV_DEFAULT);
> > + val |= ASPEED_PECI_CTRL_PECI_CLK_EN;
> > + writel(val, priv->base + ASPEED_PECI_CTRL);
> > + /*
> > + * Timing negotiation period setting.
> > + * The unit of the programmed value is 4 times of PECI clock period.
> > + */
> > + val = FIELD_PREP(ASPEED_PECI_T_NEGO_MSG_MASK, priv->msg_timing);
> > + val |= FIELD_PREP(ASPEED_PECI_T_NEGO_ADDR_MASK, priv->addr_timing);
> > + writel(val, priv->base + ASPEED_PECI_TIMING_NEGOTIATION);
> > +
> > + /* Clear interrupts */
> > + val = readl(priv->base + ASPEED_PECI_INT_STS) |
> > ASPEED_PECI_INT_MASK;
> > + writel(val, priv->base + ASPEED_PECI_INT_STS);
> > +
> > + /* Set timing negotiation mode and enable interrupts */
> > + val = FIELD_PREP(ASPEED_PECI_TIMING_NEGO_SEL_MASK,
> > ASPEED_PECI_1ST_BIT_OF_ADDR_NEGO);
> > + val |= ASPEED_PECI_INT_MASK;
> > + writel(val, priv->base + ASPEED_PECI_INT_CTRL);
> > +
> > + val = FIELD_PREP(ASPEED_PECI_CTRL_SAMPLING_MASK, priv-
> > >rd_sampling_point);
> > + val |= FIELD_PREP(ASPEED_PECI_CTRL_CLK_DIV_MASK, priv->clk_div);
> > + val |= ASPEED_PECI_CTRL_PECI_EN;
> > + val |= ASPEED_PECI_CTRL_PECI_CLK_EN;
> > + writel(val, priv->base + ASPEED_PECI_CTRL);
> > +}
> > +
> > +static inline int aspeed_peci_check_idle(struct aspeed_peci *priv)
> > +{
> > + u32 cmd_sts = readl(priv->base + ASPEED_PECI_CMD);
> > +
> > + if (FIELD_GET(ASPEED_PECI_CMD_STS_MASK, cmd_sts) ==
> > ASPEED_PECI_CMD_STS_ADDR_T_NEGO)
> > + aspeed_peci_init_regs(priv);
> > +
> > + return readl_poll_timeout(priv->base + ASPEED_PECI_CMD,
> > + cmd_sts,
> > + !(cmd_sts & ASPEED_PECI_CMD_IDLE_MASK),
> > + ASPEED_PECI_IDLE_CHECK_INTERVAL_US,
> > + ASPEED_PECI_IDLE_CHECK_TIMEOUT_US);
> > +}
> > +
> > +static int aspeed_peci_xfer(struct peci_controller *controller,
> > + u8 addr, struct peci_request *req)
> > +{
> > + struct aspeed_peci *priv = dev_get_drvdata(controller->dev.parent);
> > + unsigned long flags, timeout = msecs_to_jiffies(priv-
> > >cmd_timeout_ms);
> > + u32 peci_head;
> > + int ret;
> > +
> > + if (req->tx.len > ASPEED_PECI_DATA_BUF_SIZE_MAX ||
> > + req->rx.len > ASPEED_PECI_DATA_BUF_SIZE_MAX)
> > + return -EINVAL;
> > +
> > + /* Check command sts and bus idle state */
> > + ret = aspeed_peci_check_idle(priv);
> > + if (ret)
> > + return ret; /* -ETIMEDOUT */
> > +
> > + spin_lock_irqsave(&priv->lock, flags);
> > + reinit_completion(&priv->xfer_complete);
> > +
> > + peci_head = FIELD_PREP(ASPEED_PECI_TARGET_ADDR_MASK, addr) |
> > + FIELD_PREP(ASPEED_PECI_WR_LEN_MASK, req->tx.len) |
> > + FIELD_PREP(ASPEED_PECI_RD_LEN_MASK, req->rx.len);
> > +
> > + writel(peci_head, priv->base + ASPEED_PECI_RW_LENGTH);
> > +
> > + memcpy_toio(priv->base + ASPEED_PECI_WR_DATA0, req->tx.buf,
> > min_t(u8, req->tx.len, 16));
> > + if (req->tx.len > 16)
> > + memcpy_toio(priv->base + ASPEED_PECI_WR_DATA4, req->tx.buf +
> > 16,
> > + req->tx.len - 16);
> > +
> > + dev_dbg(priv->dev, "HEAD : 0x%08x\n", peci_head);
> > + print_hex_dump_bytes("TX : ", DUMP_PREFIX_NONE, req->tx.buf, req-
> > >tx.len);
>
> On CONFIG_DYNAMIC_DEBUG=n builds the kernel will do all the work of
> reading through this buffer, but skip emitting it. Are you sure you
> want to pay that overhead for every transaction?
I can remove it or I can add something like:
#if IS_ENABLED(CONFIG_PECI_DEBUG)
#define peci_debug(fmt, ...) pr_debug(fmt, ##__VA_ARGS__)
#else
#define peci_debug(...) do { } while (0)
#endif
(and similar peci_trace with trace_printk for usage in IRQ handlers and such).
What do you think?
>
> > +
> > + priv->status = 0;
> > + writel(ASPEED_PECI_CMD_FIRE, priv->base + ASPEED_PECI_CMD);
> > + spin_unlock_irqrestore(&priv->lock, flags);
> > +
> > + ret = wait_for_completion_interruptible_timeout(&priv-
> > >xfer_complete, timeout);
>
> spin_lock_irqsave() says "I don't know if interrupts are disabled
> already, so I'll save the state, whatever it is, and restore later"
>
> wait_for_completion_interruptible_timeout() says "I know I am in a
> sleepable context where interrupts are enabled"
>
> So, one of those is wrong, i.e. should it be spin_{lock,unlock}_irq()?
You're right - I'll fix it.
>
>
> > + if (ret < 0)
> > + return ret;
> > +
> > + if (ret == 0) {
> > + dev_dbg(priv->dev, "Timeout waiting for a response!\n");
> > + return -ETIMEDOUT;
> > + }
> > +
> > + spin_lock_irqsave(&priv->lock, flags);
> > +
> > + writel(0, priv->base + ASPEED_PECI_CMD);
> > +
> > + if (priv->status != ASPEED_PECI_INT_CMD_DONE) {
> > + spin_unlock_irqrestore(&priv->lock, flags);
> > + dev_dbg(priv->dev, "No valid response!\n");
> > + return -EIO;
> > + }
> > +
> > + spin_unlock_irqrestore(&priv->lock, flags);
> > +
> > + memcpy_fromio(req->rx.buf, priv->base + ASPEED_PECI_RD_DATA0,
> > min_t(u8, req->rx.len, 16));
> > + if (req->rx.len > 16)
> > + memcpy_fromio(req->rx.buf + 16, priv->base +
> > ASPEED_PECI_RD_DATA4,
> > + req->rx.len - 16);
> > +
> > + print_hex_dump_bytes("RX : ", DUMP_PREFIX_NONE, req->rx.buf, req-
> > >rx.len);
> > +
> > + return 0;
> > +}
> > +
> > +static irqreturn_t aspeed_peci_irq_handler(int irq, void *arg)
> > +{
> > + struct aspeed_peci *priv = arg;
> > + u32 status;
> > +
> > + spin_lock(&priv->lock);
> > + status = readl(priv->base + ASPEED_PECI_INT_STS);
> > + writel(status, priv->base + ASPEED_PECI_INT_STS);
> > + priv->status |= (status & ASPEED_PECI_INT_MASK);
> > +
> > + /*
> > + * In most cases, interrupt bits will be set one by one but also
> > note
> > + * that multiple interrupt bits could be set at the same time.
> > + */
> > + if (status & ASPEED_PECI_INT_BUS_TIMEOUT)
> > + dev_dbg_ratelimited(priv->dev,
> > "ASPEED_PECI_INT_BUS_TIMEOUT\n");
> > +
> > + if (status & ASPEED_PECI_INT_BUS_CONTENTION)
> > + dev_dbg_ratelimited(priv->dev,
> > "ASPEED_PECI_INT_BUS_CONTENTION\n");
> > +
> > + if (status & ASPEED_PECI_INT_WR_FCS_BAD)
> > + dev_dbg_ratelimited(priv->dev,
> > "ASPEED_PECI_INT_WR_FCS_BAD\n");
> > +
> > + if (status & ASPEED_PECI_INT_WR_FCS_ABORT)
> > + dev_dbg_ratelimited(priv->dev,
> > "ASPEED_PECI_INT_WR_FCS_ABORT\n");
>
> Are you sure these would not be better as tracepoints? If you're
> debugging an interrupt related failure, the ratelimiting might get in
> your way when you really need to know when one of these error
> interrupts fire relative to another event.
Tracepoints are ABI(ish), and using a full blown tracepoint just for IRQ status
would probably be too much.
I was thinking about something like trace_printk hidden under a
"CONFIG_PECI_DEBUG" (see above), but perhaps that's something for the future
improvement?
>
> > +
> > + /*
> > + * All commands should be ended up with a ASPEED_PECI_INT_CMD_DONE
> > bit
> > + * set even in an error case.
> > + */
> > + if (status & ASPEED_PECI_INT_CMD_DONE)
> > + complete(&priv->xfer_complete);
>
> Hmm, no need to check if there was a sequencing error, like a command
> was never submitted?
It's handled by checking if HW is idle in xfer before a command is sent, where
we just expect a single interrupt per command.
>
> > +
> > + spin_unlock(&priv->lock);
> > +
> > + return IRQ_HANDLED;
> > +}
> > +
> > +static void aspeed_peci_property_sanitize(struct device *dev, const char
> > *propname,
> > + u32 min, u32 max, u32 default_val,
> > u32 *propval)
> > +{
> > + u32 val;
> > + int ret;
> > +
> > + ret = device_property_read_u32(dev, propname, &val);
> > + if (ret) {
> > + val = default_val;
> > + } else if (val > max || val < min) {
> > + dev_warn(dev, "Invalid %s: %u, falling back to: %u\n",
> > + propname, val, default_val);
> > +
> > + val = default_val;
> > + }
> > +
> > + *propval = val;
> > +}
> > +
> > +static void aspeed_peci_property_setup(struct aspeed_peci *priv)
> > +{
> > + aspeed_peci_property_sanitize(priv->dev, "aspeed,clock-divider",
> > + 0, ASPEED_PECI_CLK_DIV_MAX,
> > + ASPEED_PECI_CLK_DIV_DEFAULT, &priv-
> > >clk_div);
> > + aspeed_peci_property_sanitize(priv->dev, "aspeed,msg-timing",
> > + 0, ASPEED_PECI_MSG_TIMING_MAX,
> > + ASPEED_PECI_MSG_TIMING_DEFAULT, &priv-
> > >msg_timing);
> > + aspeed_peci_property_sanitize(priv->dev, "aspeed,addr-timing",
> > + 0, ASPEED_PECI_ADDR_TIMING_MAX,
> > + ASPEED_PECI_ADDR_TIMING_DEFAULT,
> > &priv->addr_timing);
> > + aspeed_peci_property_sanitize(priv->dev, "aspeed,rd-sampling-point",
> > + 0, ASPEED_PECI_RD_SAMPLING_POINT_MAX,
> > + ASPEED_PECI_RD_SAMPLING_POINT_DEFAULT,
> > + &priv->rd_sampling_point);
> > + aspeed_peci_property_sanitize(priv->dev, "cmd-timeout-ms",
> > + 1, ASPEED_PECI_CMD_TIMEOUT_MS_MAX,
> > + ASPEED_PECI_CMD_TIMEOUT_MS_DEFAULT,
> > &priv->cmd_timeout_ms);
> > +}
> > +
> > +static struct peci_controller_ops aspeed_ops = {
> > + .xfer = aspeed_peci_xfer,
> > +};
> > +
> > +static void aspeed_peci_reset_control_release(void *data)
> > +{
> > + reset_control_assert(data);
> > +}
> > +
> > +int aspeed_peci_reset_control_deassert(struct device *dev, struct
> > reset_control *rst)
>
> I'd recommend naming this devm_aspeed_peci_reset_control_deassert(),
> because I came looking here from reading probe for why there was no
> reassertion of reset on driver ->remove().
Ok.
>
> > +{
> > + int ret;
> > +
> > + ret = reset_control_deassert(rst);
> > + if (ret)
> > + return ret;
> > +
> > + return devm_add_action_or_reset(dev,
> > aspeed_peci_reset_control_release, rst);
> > +}
> > +
> > +static void aspeed_peci_clk_release(void *data)
> > +{
> > + clk_disable_unprepare(data);
> > +}
> > +
> > +static int aspeed_peci_clk_enable(struct device *dev, struct clk *clk)
>
> ...ditto on the devm prefix, just to speed readability.
Ok.
Thanks
-Iwona
>
> > +{
> > + int ret;
> > +
> > + ret = clk_prepare_enable(clk);
> > + if (ret)
> > + return ret;
> > +
> > + return devm_add_action_or_reset(dev, aspeed_peci_clk_release, clk);
> > +}
> > +
> > +static int aspeed_peci_probe(struct platform_device *pdev)
> > +{
> > + struct peci_controller *controller;
> > + struct aspeed_peci *priv;
> > + int ret;
> > +
> > + priv = devm_kzalloc(&pdev->dev, sizeof(*priv), GFP_KERNEL);
> > + if (!priv)
> > + return -ENOMEM;
> > +
> > + priv->dev = &pdev->dev;
> > + dev_set_drvdata(priv->dev, priv);
> > +
> > + priv->base = devm_platform_ioremap_resource(pdev, 0);
> > + if (IS_ERR(priv->base))
> > + return PTR_ERR(priv->base);
> > +
> > + priv->irq = platform_get_irq(pdev, 0);
> > + if (!priv->irq)
> > + return priv->irq;
> > +
> > + ret = devm_request_irq(&pdev->dev, priv->irq,
> > aspeed_peci_irq_handler,
> > + 0, "peci-aspeed", priv);
> > + if (ret)
> > + return ret;
> > +
> > + init_completion(&priv->xfer_complete);
> > + spin_lock_init(&priv->lock);
> > +
> > + priv->rst = devm_reset_control_get(&pdev->dev, NULL);
> > + if (IS_ERR(priv->rst))
> > + return dev_err_probe(priv->dev, PTR_ERR(priv->rst),
> > + "failed to get reset control\n");
> > +
> > + ret = aspeed_peci_reset_control_deassert(priv->dev, priv->rst);
> > + if (ret)
> > + return dev_err_probe(priv->dev, ret, "cannot deassert reset
> > control\n");
> > +
> > + priv->clk = devm_clk_get(priv->dev, NULL);
> > + if (IS_ERR(priv->clk))
> > + return dev_err_probe(priv->dev, PTR_ERR(priv->clk), "failed
> > to get clk\n");
> > +
> > + ret = aspeed_peci_clk_enable(priv->dev, priv->clk);
> > + if (ret)
> > + return dev_err_probe(priv->dev, ret, "failed to enable
> > clock\n");
> > +
> > + aspeed_peci_property_setup(priv);
> > +
> > + aspeed_peci_init_regs(priv);
> > +
> > + controller = devm_peci_controller_add(priv->dev, &aspeed_ops);
> > + if (IS_ERR(controller))
> > + return dev_err_probe(priv->dev, PTR_ERR(controller),
> > + "failed to add aspeed peci
> > controller\n");
> > +
> > + priv->controller = controller;
> > +
> > + return 0;
> > +}
> > +
> > +static const struct of_device_id aspeed_peci_of_table[] = {
> > + { .compatible = "aspeed,ast2400-peci", },
> > + { .compatible = "aspeed,ast2500-peci", },
> > + { .compatible = "aspeed,ast2600-peci", },
> > + { }
> > +};
> > +MODULE_DEVICE_TABLE(of, aspeed_peci_of_table);
> > +
> > +static struct platform_driver aspeed_peci_driver = {
> > + .probe = aspeed_peci_probe,
> > + .driver = {
> > + .name = "peci-aspeed",
> > + .of_match_table = aspeed_peci_of_table,
> > + },
> > +};
> > +module_platform_driver(aspeed_peci_driver);
> > +
> > +MODULE_AUTHOR("Ryan Chen <ryan_chen at aspeedtech.com>");
> > +MODULE_AUTHOR("Jae Hyun Yoo <jae.hyun.yoo at linux.intel.com>");
> > +MODULE_DESCRIPTION("ASPEED PECI driver");
> > +MODULE_LICENSE("GPL");
> > +MODULE_IMPORT_NS(PECI);
> > --
> > 2.31.1
> >
More information about the openbmc
mailing list