[PATCH v1 1/2] dt-bindings: mmc: sdhci-of-aspeed: Add power-gpio and power-switch-gpio

Steven Lee steven_lee at aspeedtech.com
Tue Apr 13 11:30:10 AEST 2021


The 04/10/2021 02:41, Rob Herring wrote:
> On Thu, Apr 08, 2021 at 09:52:17AM +0800, Steven Lee wrote:
> > AST2600-A2 EVB provides the reference design for enabling SD bus power
> > and toggling SD bus signal voltage by GPIO pins.
> > Add the definition and example for power-gpio and power-switch-gpio
> > properties.
> > 
> > In the reference design, GPIOV0 of AST2600-A2 EVB is connected to power
> > load switch that providing 3.3v to SD1 bus vdd. GPIOV1 is connected to
> > a 1.8v and a 3.3v power load switch that providing signal voltage to
> > SD1 bus.
> > If GPIOV0 is active high, SD1 bus is enabled. Otherwise, SD1 bus is
> > disabled.
> > If GPIOV1 is active high, 3.3v power load switch is enabled, SD1 signal
> > voltage is 3.3v. Otherwise, 1.8v power load switch will be enabled, SD1
> > signal voltage becomes 1.8v.
> > 
> > AST2600-A2 EVB also support toggling signal voltage for SD2 bus.
> > The design is the same as SD1 bus. It uses GPIOV2 as power-gpio and GPIOV3
> > as power-switch-gpio.
> > 
> > Signed-off-by: Steven Lee <steven_lee at aspeedtech.com>
> > ---
> >  .../devicetree/bindings/mmc/aspeed,sdhci.yaml | 25 +++++++++++++++++++
> >  1 file changed, 25 insertions(+)
> > 
> > diff --git a/Documentation/devicetree/bindings/mmc/aspeed,sdhci.yaml b/Documentation/devicetree/bindings/mmc/aspeed,sdhci.yaml
> > index 987b287f3bff..515a74614f3c 100644
> > --- a/Documentation/devicetree/bindings/mmc/aspeed,sdhci.yaml
> > +++ b/Documentation/devicetree/bindings/mmc/aspeed,sdhci.yaml
> > @@ -37,6 +37,14 @@ properties:
> >    clocks:
> >      maxItems: 1
> >      description: The SD/SDIO controller clock gate
> > +  power-gpio:
> 
> '-gpios' is the preferred form even if just 1.
> 

Thanks for reviewing, I will change the name.

> > +    description:
> > +      The GPIO for enabling/disabling SD bus power.
> > +    maxItems: 1
> 
> blank line
> 

I will remove the blank line.

> > +  power-switch-gpio:
> > +    description:
> > +      The GPIO for toggling the signal voltage between 3.3v and 1.8v.
> > +    maxItems: 1
> >  
> >  patternProperties:
> >    "^sdhci@[0-9a-f]+$":
> > @@ -61,6 +69,14 @@ patternProperties:
> >        sdhci,auto-cmd12:
> >          type: boolean
> >          description: Specifies that controller should use auto CMD12
> > +      power-gpio:
> > +        description:
> > +          The GPIO for enabling/disabling SD bus power.
> > +        maxItems: 1
> > +      power-switch-gpio:
> > +        description:
> > +          The GPIO for toggling the signal voltage between 3.3v and 1.8v.
> > +        maxItems: 1
> >      required:
> >        - compatible
> >        - reg
> > @@ -80,6 +96,7 @@ required:
> >  examples:
> >    - |
> >      #include <dt-bindings/clock/aspeed-clock.h>
> > +    #include <dt-bindings/gpio/aspeed-gpio.h>
> >      sdc at 1e740000 {
> >              compatible = "aspeed,ast2500-sd-controller";
> >              reg = <0x1e740000 0x100>;
> > @@ -94,6 +111,10 @@ examples:
> >                      interrupts = <26>;
> >                      sdhci,auto-cmd12;
> >                      clocks = <&syscon ASPEED_CLK_SDIO>;
> > +                    power-gpio = <&gpio0 ASPEED_GPIO(V, 0)
> > +                                     GPIO_ACTIVE_HIGH>;
> > +                    power-switch-gpio = <&gpio0 ASPEED_GPIO(V, 1)
> > +                                     GPIO_ACTIVE_HIGH>;
> >              };
> >  
> >              sdhci1: sdhci at 200 {
> > @@ -102,5 +123,9 @@ examples:
> >                      interrupts = <26>;
> >                      sdhci,auto-cmd12;
> >                      clocks = <&syscon ASPEED_CLK_SDIO>;
> > +                    power-gpio = <&gpio0 ASPEED_GPIO(V, 2)
> > +                                     GPIO_ACTIVE_HIGH>;
> > +                    power-switch-gpio = <&gpio0 ASPEED_GPIO(V, 3)
> > +                                     GPIO_ACTIVE_HIGH>;
> >              };
> >      };
> > -- 
> > 2.17.1
> > 


More information about the openbmc mailing list