[PATCH 2/3] Arm: dts: aspeed-g6: Add sgpio node

Billy Tsai billy_tsai at aspeedtech.com
Mon Oct 12 14:31:49 AEDT 2020


This patch is used to add sgpiom and sgpios nodes and add compatiable
string for sgpiom.

Signed-off-by: Billy Tsai <billy_tsai at aspeedtech.com>
---
 .../devicetree/bindings/gpio/sgpio-aspeed.txt |  8 +--
 arch/arm/boot/dts/aspeed-g6.dtsi              | 52 +++++++++++++++++++
 2 files changed, 57 insertions(+), 3 deletions(-)

diff --git a/Documentation/devicetree/bindings/gpio/sgpio-aspeed.txt b/Documentation/devicetree/bindings/gpio/sgpio-aspeed.txt
index d4d83916c09d..815d9b5167a5 100644
--- a/Documentation/devicetree/bindings/gpio/sgpio-aspeed.txt
+++ b/Documentation/devicetree/bindings/gpio/sgpio-aspeed.txt
@@ -1,8 +1,10 @@
 Aspeed SGPIO controller Device Tree Bindings
 --------------------------------------------
 
-This SGPIO controller is for ASPEED AST2500 SoC, it supports up to 80 full
-featured Serial GPIOs. Each of the Serial GPIO pins can be programmed to
+This SGPIO controller is for ASPEED AST2500/AST2600 SoC, it supports 2 master.
+One is up to 128 SGPIO input ports and 128 output ports concurrently(after AST2600A1)
+and Second one is up to 80.
+Each of the Serial GPIO pins can be programmed to
 support the following options:
 - Support interrupt option for each input port and various interrupt
   sensitivity option (level-high, level-low, edge-high, edge-low)
@@ -14,7 +16,7 @@ support the following options:
 Required properties:
 
 - compatible : Should be one of
-  "aspeed,ast2400-sgpio", "aspeed,ast2500-sgpio"
+  "aspeed,ast2400-sgpio", "aspeed,ast2500-sgpio", "aspeed,ast2600-sgpiom"
 - #gpio-cells : Should be 2, see gpio.txt
 - reg : Address and length of the register set for the device
 - gpio-controller : Marks the device node as a GPIO controller
diff --git a/arch/arm/boot/dts/aspeed-g6.dtsi b/arch/arm/boot/dts/aspeed-g6.dtsi
index ad19dce038ea..cb053a996e87 100644
--- a/arch/arm/boot/dts/aspeed-g6.dtsi
+++ b/arch/arm/boot/dts/aspeed-g6.dtsi
@@ -366,6 +366,58 @@
 				#interrupt-cells = <2>;
 			};
 
+			sgpiom0: sgpiom at 1e780500 {
+				#gpio-cells = <2>;
+				gpio-controller;
+				compatible = "aspeed,ast2600-sgpiom";
+				reg = <0x1e780500 0x100>;
+				interrupts = <GIC_SPI 51 IRQ_TYPE_LEVEL_HIGH>;
+				ngpios = <128>;
+				clocks = <&syscon ASPEED_CLK_APB2>;
+				interrupt-controller;
+				bus-frequency = <12000000>;
+
+				pinctrl-names = "default";
+				pinctrl-0 = <&pinctrl_sgpm1_default>;
+				status = "disabled";
+			};
+
+			sgpiom1: sgpiom at 1e780600 {
+				#gpio-cells = <2>;
+				gpio-controller;
+				compatible = "aspeed,ast2600-sgpiom";
+				reg = <0x1e780600 0x100>;
+				interrupts = <GIC_SPI 70 IRQ_TYPE_LEVEL_HIGH>;
+				ngpios = <80>;
+				clocks = <&syscon ASPEED_CLK_APB2>;
+				interrupt-controller;
+				bus-frequency = <12000000>;
+
+				pinctrl-names = "default";
+				pinctrl-0 = <&pinctrl_sgpm2_default>;
+				status = "disabled";
+			};
+
+			sgpios0: sgpios at 1e780700 {
+				#gpio-cells = <2>;
+				gpio-controller;
+				compatible = "aspeed,ast2600-sgpios";
+				reg = <0x1e780700 0x40>;
+				interrupts = <GIC_SPI 52 IRQ_TYPE_LEVEL_HIGH>;
+				clocks = <&syscon ASPEED_CLK_APB2>;
+				status = "disabled";
+			};
+
+			sgpios1: sgpios at 1e780740 {
+				#gpio-cells = <2>;
+				gpio-controller;
+				compatible = "aspeed,ast2600-sgpios";
+				reg = <0x1e780740 0x40>;
+				interrupts = <GIC_SPI 71 IRQ_TYPE_LEVEL_HIGH>;
+				clocks = <&syscon ASPEED_CLK_APB2>;
+				status = "disabled";
+			};
+
 			gpio1: gpio at 1e780800 {
 				#gpio-cells = <2>;
 				gpio-controller;
-- 
2.17.1



More information about the openbmc mailing list