[PATCH 1/2] rainier: Add leds that are off 9551 on Operator Panel

[Joel Stanley]

On Mon, 27 Jul 2020 at 12:41, vishwanatha subbanna
<vishwa at linux.vnet.ibm.com> wrote:
>
>
> These are LEDs that are controlled by 9551
>
> Signed-off-by: Vishwanatha Subbanna <vishwa at linux.vnet.ibm.com>
> ---
> arch/arm/boot/dts/aspeed-bmc-ibm-rainier.dts | 82 ++++++++++++++++++++++++++++
> 1 file changed, 82 insertions(+)
>
> diff --git a/arch/arm/boot/dts/aspeed-bmc-ibm-rainier.dts b/arch/arm/boot/dts/aspeed-bmc-ibm-rainier.dts
> index 0b5c6cc..ecbce50 100644
> --- a/arch/arm/boot/dts/aspeed-bmc-ibm-rainier.dts
> +++ b/arch/arm/boot/dts/aspeed-bmc-ibm-rainier.dts
> @@ -69,6 +69,38 @@
>                 };
>         };
>
> +       leds {
> +               compatible = "gpio-leds";
> +
> +               /* System ID LED that is at front on Op Panel */
> +               front-sys-id0 {
> +                       retain-state-shutdown;
> +                       default-state = "keep";
> +                       gpios = <&pca1 0 GPIO_ACTIVE_LOW>;
> +               };
> +
> +               /* System Attention Indicator ID LED that is at front on Op Panel */
> +               front-check-log0 {
> +                       retain-state-shutdown;
> +                       default-state = "keep";
> +                       gpios = <&pca1 1 GPIO_ACTIVE_LOW>;
> +               };
> +
> +               /* Enclosure Fault LED that is at front on Op Panel */
> +               front-enc-fault1 {
> +                       retain-state-shutdown;
> +                       default-state = "keep";
> +                       gpios = <&pca1 2 GPIO_ACTIVE_LOW>;
> +               };
> +
> +               /* System PowerOn LED that is at front on Op Panel */
> +               front-sys-pwron0 {
> +                       retain-state-shutdown;
> +                       default-state = "keep";
> +                       gpios = <&pca1 3 GPIO_ACTIVE_LOW>;
> +               };
> +       };
> +
> };

This patch is malformed. It looks like you've pasted it into your
mailer, which makes it easy to break the patch. Instead I recommend
using git-send-email to send your patches as it avoids this issue.


>
> &gpio0 {
> @@ -514,6 +546,56 @@
>                 };
>         };
>
> +       pca1: pca9551 at 60 {
> +               compatible = "nxp,pca9551";
> +               reg = <0x60>;
> +               #address-cells = <1>;
> +               #size-cells = <0>;
> +
> +               gpio-controller;
> +               #gpio-cells = <2>;
> +
> +               gpio at 0 {
> +                       reg = <0>;
> +                       type = <PCA955X_TYPE_GPIO>;
> +               };
> +
> +               gpio at 1 {
> +                       reg = <1>;
> +                       type = <PCA955X_TYPE_GPIO>;
> +               };
> +
> +               gpio at 2 {
> +                       reg = <2>;
> +                       type = <PCA955X_TYPE_GPIO>;
> +               };
> +
> +               gpio at 3 {
> +                       reg = <3>;
> +                       type = <PCA955X_TYPE_GPIO>;
> +               };
> +
> +               gpio at 4 {
> +                       reg = <4>;
> +                       type = <PCA955X_TYPE_GPIO>;
> +               };
> +
> +               gpio at 5 {
> +                       reg = <5>;
> +                       type = <PCA955X_TYPE_GPIO>;
> +               };
> +
> +               gpio at 6 {
> +                       reg = <6>;
> +                       type = <PCA955X_TYPE_GPIO>;
> +               };
> +
> +               gpio at 7 {
> +                       reg = <7>;
> +                       type = <PCA955X_TYPE_GPIO>;
> +               };
> +       };
> +
>         dps: dps310 at 76 {
>                 compatible = "infineon,dps310";
>                 reg = <0x76>;
> --
> 1.8.3.1
>
>
>