[PATCH v6] ARM: dts: aspeed: Adding Lenovo Hr630 BMC
Patrick Venture
venture at google.com
Tue May 7 00:38:04 AEST 2019
On Sun, May 5, 2019 at 8:17 PM Andrew Jeffery <andrew at aj.id.au> wrote:
>
>
>
> On Sun, 5 May 2019, at 15:38, Andrew Peng wrote:
> > Initial introduction of Lenovo Hr630 family equipped with
> > Aspeed 2500 BMC SoC. Hr630 is a x86 server development kit
> > with a ASPEED ast2500 BMC manufactured by Lenovo.
> > Specifically, This adds the Hr630 platform device tree file
> > used by the Hr630 BMC machines.
> >
> > This also adds an entry of Hr630 device tree file in Makefile
> >
> > Signed-off-by: Andrew Peng <pengms1 at lenovo.com>
> > Signed-off-by: Yonghui Liu <liuyh21 at lenovo.com>
> > Signed-off-by: Lisa Liu <liuyj19 at lenovo.com>
>
> Reviewed-by: Andrew Jeffery <andrew at aj.id.au>
Reviewed-by: Patrick Venture <venture at google.com>
>
> > ---
> > Changes in v6:
> > - add appropriate pinctrl property for uar1, uart2, uart3 and adc.
> > - remove vhub definition and comment.
> > - remove some GPIO definitions.
> > - revise Makefile according to sort alphabetically.
> > Changes in v5:
> > - revise pca9545 and pca9546 switch aliases name.
> > Changes in v4:
> > - add pca9546 switch aliases name.
> > Changes in v3:
> > - revise i2c switch aliases name.
> > Changes in v2:
> > - add i2c switch aliases name.
> > - remove the unused eeprom device from DT file.
> > - remove "Licensed under..." sentence.
> >
> > arch/arm/boot/dts/Makefile | 1 +
> > arch/arm/boot/dts/aspeed-bmc-lenovo-hr630.dts | 566 ++++++++++++++++++++++++++
> > 2 files changed, 567 insertions(+)
> > create mode 100644 arch/arm/boot/dts/aspeed-bmc-lenovo-hr630.dts
> >
> > diff --git a/arch/arm/boot/dts/Makefile b/arch/arm/boot/dts/Makefile
> > index f4f5aea..1276167 100644
> > --- a/arch/arm/boot/dts/Makefile
> > +++ b/arch/arm/boot/dts/Makefile
> > @@ -1255,6 +1255,7 @@ dtb-$(CONFIG_ARCH_ASPEED) += \
> > aspeed-bmc-facebook-cmm.dtb \
> > aspeed-bmc-facebook-tiogapass.dtb \
> > aspeed-bmc-intel-s2600wf.dtb \
> > + aspeed-bmc-lenovo-hr630.dtb \
> > aspeed-bmc-opp-lanyang.dtb \
> > aspeed-bmc-opp-palmetto.dtb \
> > aspeed-bmc-opp-romulus.dtb \
> > diff --git a/arch/arm/boot/dts/aspeed-bmc-lenovo-hr630.dts
> > b/arch/arm/boot/dts/aspeed-bmc-lenovo-hr630.dts
> > new file mode 100644
> > index 0000000..d3695a3
> > --- /dev/null
> > +++ b/arch/arm/boot/dts/aspeed-bmc-lenovo-hr630.dts
> > @@ -0,0 +1,566 @@
> > +// SPDX-License-Identifier: GPL-2.0+
> > +/*
> > + * Device Tree file for Lenovo Hr630 platform
> > + *
> > + * Copyright (C) 2019-present Lenovo
> > + */
> > +
> > +/dts-v1/;
> > +
> > +#include "aspeed-g5.dtsi"
> > +#include <dt-bindings/gpio/aspeed-gpio.h>
> > +
> > +/ {
> > + model = "HR630 BMC";
> > + compatible = "lenovo,hr630-bmc", "aspeed,ast2500";
> > +
> > + aliases {
> > + i2c14 = &i2c_rbp;
> > + i2c15 = &i2c_fbp1;
> > + i2c16 = &i2c_fbp2;
> > + i2c17 = &i2c_fbp3;
> > + i2c18 = &i2c_riser2;
> > + i2c19 = &i2c_pcie4;
> > + i2c20 = &i2c_riser1;
> > + i2c21 = &i2c_ocp;
> > + };
> > +
> > + chosen {
> > + stdout-path = &uart5;
> > + bootargs = "console=tty0 console=ttyS4,115200 earlyprintk";
> > + };
> > +
> > + memory at 80000000 {
> > + device_type = "memory";
> > + reg = <0x80000000 0x20000000>;
> > + };
> > +
> > + reserved-memory {
> > + #address-cells = <1>;
> > + #size-cells = <1>;
> > + ranges;
> > +
> > + flash_memory: region at 98000000 {
> > + no-map;
> > + reg = <0x98000000 0x00100000>; /* 1M */
> > + };
> > +
> > + gfx_memory: framebuffer {
> > + size = <0x01000000>;
> > + alignment = <0x01000000>;
> > + compatible = "shared-dma-pool";
> > + reusable;
> > + };
> > + };
> > +
> > + leds {
> > + compatible = "gpio-leds";
> > +
> > + heartbeat {
> > + gpios = <&gpio ASPEED_GPIO(J, 1) GPIO_ACTIVE_LOW>;
> > + };
> > +
> > + fault {
> > + gpios = <&gpio ASPEED_GPIO(J, 0) GPIO_ACTIVE_LOW>;
> > + };
> > + };
> > +
> > + iio-hwmon {
> > + compatible = "iio-hwmon";
> > + io-channels = <&adc 0>, <&adc 1>, <&adc 2>, <&adc 3>,
> > + <&adc 4>, <&adc 5>, <&adc 6>, <&adc 7>,
> > + <&adc 8>, <&adc 9>, <&adc 10>,
> > + <&adc 12>, <&adc 13>, <&adc 14>;
> > + };
> > +
> > +};
> > +
> > +&fmc {
> > + status = "okay";
> > + flash at 0 {
> > + status = "okay";
> > + m25p,fast-read;
> > + label = "bmc";
> > + spi-max-frequency = <50000000>;
> > +#include "openbmc-flash-layout.dtsi"
> > + };
> > +};
> > +
> > +&lpc_ctrl {
> > + status = "okay";
> > + memory-region = <&flash_memory>;
> > + flash = <&spi1>;
> > +};
> > +
> > +&uart1 {
> > + status = "okay";
> > + pinctrl-names = "default";
> > + pinctrl-0 = <&pinctrl_txd1_default
> > + &pinctrl_rxd1_default>;
> > +};
> > +
> > +&uart2 {
> > + /* Rear RS-232 connector */
> > + status = "okay";
> > + pinctrl-names = "default";
> > + pinctrl-0 = <&pinctrl_txd2_default
> > + &pinctrl_rxd2_default
> > + &pinctrl_nrts2_default
> > + &pinctrl_ndtr2_default
> > + &pinctrl_ndsr2_default
> > + &pinctrl_ncts2_default
> > + &pinctrl_ndcd2_default
> > + &pinctrl_nri2_default>;
> > +};
> > +
> > +&uart3 {
> > + status = "okay";
> > + pinctrl-names = "default";
> > + pinctrl-0 = <&pinctrl_txd3_default
> > + &pinctrl_rxd3_default>;
> > +};
> > +
> > +&uart5 {
> > + status = "okay";
> > +};
> > +
> > +&ibt {
> > + status = "okay";
> > +};
> > +
> > +&mac0 {
> > + status = "okay";
> > +
> > + pinctrl-names = "default";
> > + pinctrl-0 = <&pinctrl_rmii1_default>;
> > + use-ncsi;
> > +};
> > +
> > +&mac1 {
> > + status = "okay";
> > +
> > + pinctrl-names = "default";
> > + pinctrl-0 = <&pinctrl_rgmii2_default &pinctrl_mdio2_default>;
> > +};
> > +
> > +&adc {
> > + status = "okay";
> > +
> > + pinctrl-names = "default";
> > + pinctrl-0 = <&pinctrl_adc0_default
> > + &pinctrl_adc1_default
> > + &pinctrl_adc2_default
> > + &pinctrl_adc3_default
> > + &pinctrl_adc4_default
> > + &pinctrl_adc5_default
> > + &pinctrl_adc6_default
> > + &pinctrl_adc7_default
> > + &pinctrl_adc8_default
> > + &pinctrl_adc9_default
> > + &pinctrl_adc10_default
> > + &pinctrl_adc12_default
> > + &pinctrl_adc13_default
> > + &pinctrl_adc14_default>;
> > +};
> > +
> > +&i2c0 {
> > + status = "okay";
> > + /* temp1 inlet */
> > + tmp75 at 4e {
> > + compatible = "national,lm75";
> > + reg = <0x4e>;
> > + };
> > +};
> > +
> > +&i2c1 {
> > + status = "okay";
> > + /* temp2 outlet */
> > + tmp75 at 4d {
> > + compatible = "national,lm75";
> > + reg = <0x4d>;
> > + };
> > +};
> > +
> > +&i2c2 {
> > + status = "okay";
> > +};
> > +
> > +&i2c3 {
> > + status = "okay";
> > +};
> > +
> > +&i2c4 {
> > + status = "okay";
> > +};
> > +
> > +&i2c5 {
> > + status = "okay";
> > +};
> > +
> > +&i2c6 {
> > + status = "okay";
> > + /* Slot 0,
> > + * Slot 1,
> > + * Slot 2,
> > + * Slot 3
> > + */
> > +
> > + i2c-switch at 70 {
> > + compatible = "nxp,pca9545";
> > + reg = <0x70>;
> > + #address-cells = <1>;
> > + #size-cells = <0>;
> > + i2c-mux-idle-disconnect; /* may use mux at 70 next. */
Per an earlier email, this comment, and its sibling comment don't
really make sense, and there's no chance of a bus collision here since
the switches reside on different buses. If the switches were under
the same bus then accesses could collide the address ranges without
the "i2c-mux-idle-disconnect" property set.
I'm ok with this being here, but someone will want to send a follow-up
patchset at some point to remove the comment - at the least.
> > +
> > + i2c_rbp: i2c at 0 {
> > + #address-cells = <1>;
> > + #size-cells = <0>;
> > + reg = <0>;
> > + };
> > +
> > + i2c_fbp1: i2c at 1 {
> > + #address-cells = <1>;
> > + #size-cells = <0>;
> > + reg = <1>;
> > + };
> > +
> > + i2c_fbp2: i2c at 2 {
> > + #address-cells = <1>;
> > + #size-cells = <0>;
> > + reg = <2>;
> > + };
> > +
> > + i2c_fbp3: i2c at 3 {
> > + #address-cells = <1>;
> > + #size-cells = <0>;
> > + reg = <3>;
> > + };
> > + };
> > +};
> > +
> > +&i2c7 {
> > + status = "okay";
> > +
> > + /* Slot 0,
> > + * Slot 1,
> > + * Slot 2,
> > + * Slot 3
> > + */
> > + i2c-switch at 76 {
> > + compatible = "nxp,pca9546";
> > + reg = <0x76>;
> > + #address-cells = <1>;
> > + #size-cells = <0>;
> > + i2c-mux-idle-disconnect; /* may use mux at 76 next. */
> > +
> > + i2c_riser2: i2c at 0 {
> > + #address-cells = <1>;
> > + #size-cells = <0>;
> > + reg = <0>;
> > + };
> > +
> > + i2c_pcie4: i2c at 1 {
> > + #address-cells = <1>;
> > + #size-cells = <0>;
> > + reg = <1>;
> > + };
> > +
> > + i2c_riser1: i2c at 2 {
> > + #address-cells = <1>;
> > + #size-cells = <0>;
> > + reg = <2>;
> > + };
> > +
> > + i2c_ocp: i2c at 3 {
> > + #address-cells = <1>;
> > + #size-cells = <0>;
> > + reg = <3>;
> > + };
> > + };
> > +};
> > +
> > +&i2c8 {
> > + status = "okay";
> > +
> > + eeprom at 57 {
> > + compatible = "atmel,24c256";
> > + reg = <0x57>;
> > + pagesize = <16>;
> > + };
> > +};
> > +
> > +&i2c9 {
> > + status = "okay";
> > +};
> > +
> > +&i2c10 {
> > + status = "okay";
> > +};
> > +
> > +&i2c11 {
> > + status = "okay";
> > +};
> > +
> > +&i2c12 {
> > + status = "okay";
> > +};
> > +
> > +&ehci1 {
> > + status = "okay";
> > +};
> > +
> > +&uhci {
> > + status = "okay";
> > +};
> > +
> > +&gfx {
> > + status = "okay";
> > + memory-region = <&gfx_memory>;
> > +};
> > +
> > +&pwm_tacho {
> > + status = "okay";
> > + pinctrl-names = "default";
> > + pinctrl-0 = <&pinctrl_pwm0_default
> > + &pinctrl_pwm1_default
> > + &pinctrl_pwm2_default
> > + &pinctrl_pwm3_default
> > + &pinctrl_pwm4_default
> > + &pinctrl_pwm5_default
> > + &pinctrl_pwm6_default>;
> > +
> > + fan at 0 {
> > + reg = <0x00>;
> > + aspeed,fan-tach-ch = /bits/ 8 <0x00>;
> > + };
> > +
> > + fan at 1 {
> > + reg = <0x00>;
> > + aspeed,fan-tach-ch = /bits/ 8 <0x01>;
> > + };
> > +
> > + fan at 2 {
> > + reg = <0x01>;
> > + aspeed,fan-tach-ch = /bits/ 8 <0x02>;
> > + };
> > +
> > + fan at 3 {
> > + reg = <0x01>;
> > + aspeed,fan-tach-ch = /bits/ 8 <0x03>;
> > + };
> > +
> > + fan at 4 {
> > + reg = <0x02>;
> > + aspeed,fan-tach-ch = /bits/ 8 <0x04>;
> > + };
> > +
> > + fan at 5 {
> > + reg = <0x02>;
> > + aspeed,fan-tach-ch = /bits/ 8 <0x05>;
> > + };
> > +
> > + fan at 6 {
> > + reg = <0x03>;
> > + aspeed,fan-tach-ch = /bits/ 8 <0x06>;
> > + };
> > +
> > + fan at 7 {
> > + reg = <0x03>;
> > + aspeed,fan-tach-ch = /bits/ 8 <0x07>;
> > + };
> > +
> > + fan at 8 {
> > + reg = <0x04>;
> > + aspeed,fan-tach-ch = /bits/ 8 <0x08>;
> > + };
> > +
> > + fan at 9 {
> > + reg = <0x04>;
> > + aspeed,fan-tach-ch = /bits/ 8 <0x09>;
> > + };
> > +
> > + fan at 10 {
> > + reg = <0x05>;
> > + aspeed,fan-tach-ch = /bits/ 8 <0x0a>;
> > + };
> > +
> > + fan at 11 {
> > + reg = <0x05>;
> > + aspeed,fan-tach-ch = /bits/ 8 <0x0b>;
> > + };
> > +
> > + fan at 12 {
> > + reg = <0x06>;
> > + aspeed,fan-tach-ch = /bits/ 8 <0x0c>;
> > + };
> > +
> > + fan at 13 {
> > + reg = <0x06>;
> > + aspeed,fan-tach-ch = /bits/ 8 <0x0d>;
> > + };
> > +};
> > +
> > +&gpio {
> > +
> > + pin_gpio_b5 {
> > + gpio-hog;
> > + gpios = <ASPEED_GPIO(B, 5) GPIO_ACTIVE_HIGH>;
> > + output-high;
> > + line-name = "IRQ_BMC_PCH_SMI_LPC_N";
> > + };
> > +
> > + pin_gpio_f0 {
> > + gpio-hog;
> > + gpios = <ASPEED_GPIO(F, 0) GPIO_ACTIVE_HIGH>;
> > + output-low;
> > + line-name = "IRQ_BMC_PCH_NMI_R";
> > + };
> > +
> > + pin_gpio_f3 {
> > + gpio-hog;
> > + gpios = <ASPEED_GPIO(F, 3) GPIO_ACTIVE_HIGH>;
> > + output-high;
> > + line-name = "I2C_BUS0_RST_OUT_N";
> > + };
> > +
> > + pin_gpio_f4 {
> > + gpio-hog;
> > + gpios = <ASPEED_GPIO(F, 4) GPIO_ACTIVE_HIGH>;
> > + output-low;
> > + line-name = "FM_SKT0_FAULT_LED";
> > + };
> > +
> > + pin_gpio_f5 {
> > + gpio-hog;
> > + gpios = <ASPEED_GPIO(F, 5) GPIO_ACTIVE_HIGH>;
> > + output-low;
> > + line-name = "FM_SKT1_FAULT_LED";
> > + };
> > +
> > + pin_gpio_g4 {
> > + gpio-hog;
> > + gpios = <ASPEED_GPIO(G, 4) GPIO_ACTIVE_HIGH>;
> > + output-high;
> > + line-name = "FAN_PWR_CTL_N";
> > + };
> > +
> > + pin_gpio_g7 {
> > + gpio-hog;
> > + gpios = <ASPEED_GPIO(G, 7) GPIO_ACTIVE_HIGH>;
> > + output-high;
> > + line-name = "RST_BMC_PCIE_I2CMUX_N";
> > + };
> > +
> > + pin_gpio_h2 {
> > + gpio-hog;
> > + gpios = <ASPEED_GPIO(H, 2) GPIO_ACTIVE_HIGH>;
> > + output-high;
> > + line-name = "PSU1_FFS_N_R";
> > + };
> > +
> > + pin_gpio_h3 {
> > + gpio-hog;
> > + gpios = <ASPEED_GPIO(H, 3) GPIO_ACTIVE_HIGH>;
> > + output-high;
> > + line-name = "PSU2_FFS_N_R";
> > + };
> > +
> > + pin_gpio_i3 {
> > + gpio-hog;
> > + gpios = <ASPEED_GPIO(I, 3) GPIO_ACTIVE_HIGH>;
> > + output-high;
> > + line-name = "BMC_INTRUDED_COVER";
> > + };
> > +
> > + pin_gpio_j2 {
> > + gpio-hog;
> > + gpios = <ASPEED_GPIO(J, 2) GPIO_ACTIVE_HIGH>;
> > + output-high;
> > + line-name = "BMC_BIOS_UPDATE_N";
> > + };
> > +
> > + pin_gpio_j3 {
> > + gpio-hog;
> > + gpios = <ASPEED_GPIO(J, 3) GPIO_ACTIVE_HIGH>;
> > + output-high;
> > + line-name = "RST_BMC_HDD_I2CMUX_N";
> > + };
> > +
> > + pin_gpio_s2 {
> > + gpio-hog;
> > + gpios = <ASPEED_GPIO(S, 2) GPIO_ACTIVE_HIGH>;
> > + output-high;
> > + line-name = "BMC_VGA_SW";
> > + };
> > +
> > + pin_gpio_s4 {
> > + gpio-hog;
> > + gpios = <ASPEED_GPIO(S, 4) GPIO_ACTIVE_HIGH>;
> > + output;
> > + line-name = "VBAT_EN_N";
> > + };
> > +
> > + pin_gpio_s6 {
> > + gpio-hog;
> > + gpios = <ASPEED_GPIO(S, 6) GPIO_ACTIVE_HIGH>;
> > + output-high;
> > + line-name = "PU_BMC_GPIOS6";
> > + };
> > +
> > + pin_gpio_y0 {
> > + gpio-hog;
> > + gpios = <ASPEED_GPIO(Y, 0) GPIO_ACTIVE_HIGH>;
> > + output-low;
> > + line-name = "BMC_NCSI_MUX_CTL_S0";
> > + };
> > +
> > + pin_gpio_y1 {
> > + gpio-hog;
> > + gpios = <ASPEED_GPIO(Y, 1) GPIO_ACTIVE_HIGH>;
> > + output-low;
> > + line-name = "BMC_NCSI_MUX_CTL_S1";
> > + };
> > +
> > + pin_gpio_z0 {
> > + gpio-hog;
> > + gpios = <ASPEED_GPIO(Z, 0) GPIO_ACTIVE_HIGH>;
> > + output-high;
> > + line-name = "I2C_RISER2_INT_N";
> > + };
> > +
> > + pin_gpio_z2 {
> > + gpio-hog;
> > + gpios = <ASPEED_GPIO(Z, 2) GPIO_ACTIVE_HIGH>;
> > + output-high;
> > + line-name = "I2C_RISER2_RESET_N";
> > + };
> > +
> > + pin_gpio_z3 {
> > + gpio-hog;
> > + gpios = <ASPEED_GPIO(Z, 3) GPIO_ACTIVE_HIGH>;
> > + output-high;
> > + line-name = "FM_BMC_PCH_SCI_LPC_N";
> > + };
> > +
> > + pin_gpio_z7 {
> > + gpio-hog;
> > + gpios = <ASPEED_GPIO(Z, 7) GPIO_ACTIVE_HIGH>;
> > + output-low;
> > + line-name = "BMC_POST_CMPLT_N";
> > + };
> > +
> > + pin_gpio_aa0 {
> > + gpio-hog;
> > + gpios = <ASPEED_GPIO(AA, 0) GPIO_ACTIVE_HIGH>;
> > + output-low;
> > + line-name = "HOST_BMC_USB_SEL";
> > + };
> > +
> > + pin_gpio_aa5 {
> > + gpio-hog;
> > + gpios = <ASPEED_GPIO(AA, 5) GPIO_ACTIVE_HIGH>;
> > + output-high;
> > + line-name = "I2C_BUS1_RST_OUT_N";
> > + };
> > +
> > +};
> > --
> > 2.7.4
> >
> >
More information about the openbmc
mailing list