[PATCH v2 4/4] net: NC-SI setup and handling

[Samuel Mendoza-Jonas]

Add the handling of NC-SI ethernet frames, and add a check at the start
of net_loop() to configure NC-SI before starting other network commands.
This also adds an "ncsi" command to manually start NC-SI configuration.

Signed-off-by: Samuel Mendoza-Jonas <sam at mendozajonas.com>
---
v2: Update ncsi command help text

 cmd/Kconfig   |  8 ++++++++
 cmd/net.c     | 18 ++++++++++++++++++
 include/net.h |  2 +-
 net/net.c     | 27 ++++++++++++++++++++++++++-
 4 files changed, 53 insertions(+), 2 deletions(-)

diff --git a/cmd/Kconfig b/cmd/Kconfig
index 0badcb3fe0..9851b04972 100644
--- a/cmd/Kconfig
+++ b/cmd/Kconfig
@@ -1332,6 +1332,14 @@ config CMD_LINK_LOCAL
 	help
 	  Acquire a network IP address using the link-local protocol
 
+config CMD_NCSI
+	bool "ncsi"
+	depends on PHY_NCSI
+	help
+	  Manually configure the attached NIC via NC-SI.
+	  Normally this happens automatically before other network
+	  operations.
+
 endif
 
 config CMD_ETHSW
diff --git a/cmd/net.c b/cmd/net.c
index 89721b8f8b..7d2c21ba4d 100644
--- a/cmd/net.c
+++ b/cmd/net.c
@@ -457,3 +457,21 @@ U_BOOT_CMD(
 );
 
 #endif  /* CONFIG_CMD_LINK_LOCAL */
+
+#if defined(CONFIG_CMD_NCSI)
+static int do_ncsi(cmd_tbl_t *cmdtp, int flag, int argc,
+		   char * const argv[])
+{
+	if (net_loop(NCSI) < 0)
+		return CMD_RET_FAILURE;
+
+	return CMD_RET_SUCCESS;
+}
+
+U_BOOT_CMD(
+	ncsi,	1,	1,	do_ncsi,
+	"Configure attached NIC via NC-SI",
+	""
+);
+
+#endif  /* CONFIG_CMD_NCSI */
diff --git a/include/net.h b/include/net.h
index 20c448ee60..9189f0fb53 100644
--- a/include/net.h
+++ b/include/net.h
@@ -531,7 +531,7 @@ extern int		net_restart_wrap;	/* Tried all network devices */
 
 enum proto_t {
 	BOOTP, RARP, ARP, TFTPGET, DHCP, PING, DNS, NFS, CDP, NETCONS, SNTP,
-	TFTPSRV, TFTPPUT, LINKLOCAL, FASTBOOT, WOL
+	TFTPSRV, TFTPPUT, LINKLOCAL, FASTBOOT, WOL, NCSI
 };
 
 extern char	net_boot_file_name[1024];/* Boot File name */
diff --git a/net/net.c b/net/net.c
index 58b0417cbe..a59169a032 100644
--- a/net/net.c
+++ b/net/net.c
@@ -95,6 +95,7 @@
 #include <net.h>
 #include <net/fastboot.h>
 #include <net/tftp.h>
+#include <net/ncsi.h>
 #if defined(CONFIG_LED_STATUS)
 #include <miiphy.h>
 #include <status_led.h>
@@ -407,6 +408,16 @@ int net_loop(enum proto_t protocol)
 	net_try_count = 1;
 	debug_cond(DEBUG_INT_STATE, "--- net_loop Entry\n");
 
+#ifdef CONFIG_PHY_NCSI
+	if (protocol != NCSI && !ncsi_active()) {
+		printf("%s: configuring NCSI first\n", __func__);
+		if (net_loop(NCSI) < 0)
+			return ret;
+		eth_init_state_only();
+		goto restart;
+	}
+#endif
+
 	bootstage_mark_name(BOOTSTAGE_ID_ETH_START, "eth_start");
 	net_init();
 	if (eth_is_on_demand_init() || protocol != NETCONS) {
@@ -420,6 +431,7 @@ int net_loop(enum proto_t protocol)
 	} else {
 		eth_init_state_only();
 	}
+
 restart:
 #ifdef CONFIG_USB_KEYBOARD
 	net_busy_flag = 0;
@@ -526,6 +538,11 @@ restart:
 		case WOL:
 			wol_start();
 			break;
+#endif
+#if defined(CONFIG_CMD_NCSI)
+		case NCSI:
+			ncsi_probe_packages();
+			break;
 #endif
 		default:
 			break;
@@ -637,7 +654,7 @@ restart:
 				env_set_hex("filesize", net_boot_file_size);
 				env_set_hex("fileaddr", load_addr);
 			}
-			if (protocol != NETCONS)
+			if (protocol != NETCONS && protocol != NCSI)
 				eth_halt();
 			else
 				eth_halt_state_only();
@@ -1318,6 +1335,11 @@ void net_process_received_packet(uchar *in_packet, int len)
 	case PROT_WOL:
 		wol_receive(ip, len);
 		break;
+#endif
+#ifdef CONFIG_PHY_NCSI
+	case PROT_NCSI:
+		ncsi_receive(et, ip, len);
+		break;
 #endif
 	}
 }
@@ -1379,6 +1401,9 @@ common:
 
 #ifdef CONFIG_CMD_RARP
 	case RARP:
+#endif
+#ifdef CONFIG_CMD_NCSI
+	case NCSI:
 #endif
 	case BOOTP:
 	case CDP:
-- 
2.21.0