[U-Boot] [PATCH v2 4/4] net: NC-SI setup and handling

Joe Hershberger joe.hershberger at ni.com
Wed Jul 10 09:33:47 AEST 2019


On Mon, Jun 17, 2019 at 8:43 PM Samuel Mendoza-Jonas
<sam at mendozajonas.com> wrote:
>
> Add the handling of NC-SI ethernet frames, and add a check at the start
> of net_loop() to configure NC-SI before starting other network commands.
> This also adds an "ncsi" command to manually start NC-SI configuration.
>
> Signed-off-by: Samuel Mendoza-Jonas <sam at mendozajonas.com>
> ---
> v2: Update ncsi command help text
>
>  cmd/Kconfig   |  8 ++++++++
>  cmd/net.c     | 18 ++++++++++++++++++
>  include/net.h |  2 +-
>  net/net.c     | 27 ++++++++++++++++++++++++++-
>  4 files changed, 53 insertions(+), 2 deletions(-)
>
> diff --git a/cmd/Kconfig b/cmd/Kconfig
> index 0badcb3fe0..9851b04972 100644
> --- a/cmd/Kconfig
> +++ b/cmd/Kconfig
> @@ -1332,6 +1332,14 @@ config CMD_LINK_LOCAL
>         help
>           Acquire a network IP address using the link-local protocol
>
> +config CMD_NCSI
> +       bool "ncsi"
> +       depends on PHY_NCSI
> +       help
> +         Manually configure the attached NIC via NC-SI.
> +         Normally this happens automatically before other network
> +         operations.
> +
>  endif
>
>  config CMD_ETHSW
> diff --git a/cmd/net.c b/cmd/net.c
> index 89721b8f8b..7d2c21ba4d 100644
> --- a/cmd/net.c
> +++ b/cmd/net.c
> @@ -457,3 +457,21 @@ U_BOOT_CMD(
>  );
>
>  #endif  /* CONFIG_CMD_LINK_LOCAL */
> +
> +#if defined(CONFIG_CMD_NCSI)
> +static int do_ncsi(cmd_tbl_t *cmdtp, int flag, int argc,
> +                  char * const argv[])
> +{
> +       if (net_loop(NCSI) < 0)
> +               return CMD_RET_FAILURE;
> +
> +       return CMD_RET_SUCCESS;
> +}
> +
> +U_BOOT_CMD(
> +       ncsi,   1,      1,      do_ncsi,
> +       "Configure attached NIC via NC-SI",
> +       ""
> +);
> +
> +#endif  /* CONFIG_CMD_NCSI */
> diff --git a/include/net.h b/include/net.h
> index 20c448ee60..9189f0fb53 100644
> --- a/include/net.h
> +++ b/include/net.h
> @@ -531,7 +531,7 @@ extern int          net_restart_wrap;       /* Tried all network devices */
>
>  enum proto_t {
>         BOOTP, RARP, ARP, TFTPGET, DHCP, PING, DNS, NFS, CDP, NETCONS, SNTP,
> -       TFTPSRV, TFTPPUT, LINKLOCAL, FASTBOOT, WOL
> +       TFTPSRV, TFTPPUT, LINKLOCAL, FASTBOOT, WOL, NCSI
>  };
>
>  extern char    net_boot_file_name[1024];/* Boot File name */
> diff --git a/net/net.c b/net/net.c
> index 58b0417cbe..a59169a032 100644
> --- a/net/net.c
> +++ b/net/net.c
> @@ -95,6 +95,7 @@
>  #include <net.h>
>  #include <net/fastboot.h>
>  #include <net/tftp.h>
> +#include <net/ncsi.h>
>  #if defined(CONFIG_LED_STATUS)
>  #include <miiphy.h>
>  #include <status_led.h>
> @@ -407,6 +408,16 @@ int net_loop(enum proto_t protocol)
>         net_try_count = 1;
>         debug_cond(DEBUG_INT_STATE, "--- net_loop Entry\n");
>
> +#ifdef CONFIG_PHY_NCSI
> +       if (protocol != NCSI && !ncsi_active()) {
> +               printf("%s: configuring NCSI first\n", __func__);

NC-SI

> +               if (net_loop(NCSI) < 0)
> +                       return ret;
> +               eth_init_state_only();
> +               goto restart;
> +       }
> +#endif
> +
>         bootstage_mark_name(BOOTSTAGE_ID_ETH_START, "eth_start");
>         net_init();
>         if (eth_is_on_demand_init() || protocol != NETCONS) {
> @@ -420,6 +431,7 @@ int net_loop(enum proto_t protocol)
>         } else {
>                 eth_init_state_only();
>         }
> +
>  restart:
>  #ifdef CONFIG_USB_KEYBOARD
>         net_busy_flag = 0;
> @@ -526,6 +538,11 @@ restart:
>                 case WOL:
>                         wol_start();
>                         break;
> +#endif
> +#if defined(CONFIG_CMD_NCSI)
> +               case NCSI:
> +                       ncsi_probe_packages();
> +                       break;
>  #endif
>                 default:
>                         break;
> @@ -637,7 +654,7 @@ restart:
>                                 env_set_hex("filesize", net_boot_file_size);
>                                 env_set_hex("fileaddr", load_addr);
>                         }
> -                       if (protocol != NETCONS)
> +                       if (protocol != NETCONS && protocol != NCSI)

Why is this using eth_halt_state_only()? It is not using the
eth_init_state_only().

>                                 eth_halt();
>                         else
>                                 eth_halt_state_only();
> @@ -1318,6 +1335,11 @@ void net_process_received_packet(uchar *in_packet, int len)
>         case PROT_WOL:
>                 wol_receive(ip, len);
>                 break;
> +#endif
> +#ifdef CONFIG_PHY_NCSI
> +       case PROT_NCSI:
> +               ncsi_receive(et, ip, len);
> +               break;
>  #endif
>         }
>  }
> @@ -1379,6 +1401,9 @@ common:
>
>  #ifdef CONFIG_CMD_RARP
>         case RARP:
> +#endif
> +#ifdef CONFIG_CMD_NCSI
> +       case NCSI:
>  #endif
>         case BOOTP:
>         case CDP:
> --
> 2.21.0
>
> _______________________________________________
> U-Boot mailing list
> U-Boot at lists.denx.de
> https://lists.denx.de/listinfo/u-boot


More information about the openbmc mailing list