[PATCH v3] ARM: dts: aspeed: Adding Lenovo Hr630 BMC
Patrick Venture
venture at google.com
Thu Apr 25 00:16:17 AEST 2019
On Wed, Apr 24, 2019 at 5:29 AM Andrew Peng <pengms1 at lenovo.com> wrote:
>
> Initial introduction of Lenovo Hr630 family equipped with
> Aspeed 2500 BMC SoC. Hr630 is a x86 server development kit
> with a ASPEED ast2500 BMC manufactured by Lenovo.
> Specifically, This adds the Hr630 platform device tree file
> used by the Hr630 BMC machines.
>
> This also adds an entry of Hr630 device tree file in Makefile
>
> Signed-off-by: Andrew Peng <pengms1 at lenovo.com>
> Signed-off-by: Yonghui Liu <liuyh21 at lenovo.com>
> Signed-off-by: Lisa Liu <liuyj19 at lenovo.com>
> ---
> Changes in v3:
> - revise i2c switch aliases name.
> Changes in v2:
> - add i2c switch aliases name.
> - remove the unused eeprom device from DT file.
> - remove "Licensed under..." sentence.
>
> arch/arm/boot/dts/Makefile | 3 +-
> arch/arm/boot/dts/aspeed-bmc-lenovo-hr630.dts | 886 ++++++++++++++++++++++++++
> 2 files changed, 888 insertions(+), 1 deletion(-)
> create mode 100644 arch/arm/boot/dts/aspeed-bmc-lenovo-hr630.dts
>
> diff --git a/arch/arm/boot/dts/Makefile b/arch/arm/boot/dts/Makefile
> index f4f5aea..375e53b 100644
> --- a/arch/arm/boot/dts/Makefile
> +++ b/arch/arm/boot/dts/Makefile
> @@ -1261,4 +1261,5 @@ dtb-$(CONFIG_ARCH_ASPEED) += \
> aspeed-bmc-opp-witherspoon.dtb \
> aspeed-bmc-opp-zaius.dtb \
> aspeed-bmc-portwell-neptune.dtb \
> - aspeed-bmc-quanta-q71l.dtb
> + aspeed-bmc-quanta-q71l.dtb \
> + aspeed-bmc-lenovo-hr630.dtb
> diff --git a/arch/arm/boot/dts/aspeed-bmc-lenovo-hr630.dts b/arch/arm/boot/dts/aspeed-bmc-lenovo-hr630.dts
> new file mode 100644
> index 0000000..5c45523
> --- /dev/null
> +++ b/arch/arm/boot/dts/aspeed-bmc-lenovo-hr630.dts
> @@ -0,0 +1,886 @@
> +// SPDX-License-Identifier: GPL-2.0+
> +/*
> + * Device Tree file for Lenovo Hr630 platform
> + *
> + * Copyright (C) 2019-present Lenovo
> + */
> +
> +/dts-v1/;
> +
> +#include "aspeed-g5.dtsi"
> +#include <dt-bindings/gpio/aspeed-gpio.h>
> +
> +/ {
> + model = "HR630 BMC";
> + compatible = "lenovo,hr630-bmc", "aspeed,ast2500";
> +
> + aliases {
> + pca9545_i2c0 = &i2c_rbp;
> + pca9545_i2c1 = &i2c_fbp1;
> + pca9545_i2c2 = &i2c_fbp2;
> + pca9545_i2c3 = &i2c_fbp3;
> + };
> +
> + chosen {
> + stdout-path = &uart5;
> + bootargs = "console=tty0 console=ttyS4,115200 earlyprintk";
> + };
> +
> + memory at 80000000 {
> + device_type = "memory";
> + reg = <0x80000000 0x20000000>;
> + };
> +
> + reserved-memory {
> + #address-cells = <1>;
> + #size-cells = <1>;
> + ranges;
> +
> + flash_memory: region at 98000000 {
> + no-map;
> + reg = <0x98000000 0x00100000>; /* 1M */
> + };
> +
> + gfx_memory: framebuffer {
> + size = <0x01000000>;
> + alignment = <0x01000000>;
> + compatible = "shared-dma-pool";
> + reusable;
> + };
> + };
> +
> + leds {
> + compatible = "gpio-leds";
> +
> + heartbeat {
> + gpios = <&gpio ASPEED_GPIO(J, 1) GPIO_ACTIVE_LOW>;
> + };
> +
> + fault {
> + gpios = <&gpio ASPEED_GPIO(J, 0) GPIO_ACTIVE_LOW>;
> + };
> + };
> +
> + iio-hwmon {
> + compatible = "iio-hwmon";
> + io-channels = <&adc 0>, <&adc 1>, <&adc 2>, <&adc 3>,
> + <&adc 4>, <&adc 5>, <&adc 6>, <&adc 7>,
> + <&adc 8>, <&adc 9>, <&adc 10>,
> + <&adc 12>, <&adc 13>, <&adc 14>;
> + };
> +
> +};
> +
> +&fmc {
> + status = "okay";
> + flash at 0 {
> + status = "okay";
> + m25p,fast-read;
> + label = "bmc";
> + spi-max-frequency = <50000000>;
> +#include "openbmc-flash-layout.dtsi"
> + };
> +};
> +
> +&lpc_ctrl {
> + status = "okay";
> + memory-region = <&flash_memory>;
> + flash = <&spi1>;
> +};
> +
> +&uart1 {
> + status = "okay";
> +};
> +
> +&uart2 {
> + status = "okay";
> +};
> +
> +&uart3 {
> + status = "okay";
> +};
> +
> +&uart5 {
> + status = "okay";
> +};
> +
> +&vuart {
> + status = "okay";
> +};
> +
> +&ibt {
> + status = "okay";
> +};
> +
> +&mac0 {
> + status = "okay";
> +
> + pinctrl-names = "default";
> + pinctrl-0 = <&pinctrl_rmii1_default>;
> + use-ncsi;
> +};
> +
> +&mac1 {
> + status = "okay";
> +
> + pinctrl-names = "default";
> + pinctrl-0 = <&pinctrl_rgmii2_default &pinctrl_mdio2_default>;
> +};
> +
> +&adc {
> + status = "okay";
> +};
> +
> +&i2c0 {
> + status = "okay";
> + /* temp1 inlet */
> + tmp75 at 4e {
> + compatible = "national,lm75";
> + reg = <0x4e>;
> + };
> +};
> +
> +&i2c1 {
> + status = "okay";
> + /* temp2 outlet */
> + tmp75 at 4d {
> + compatible = "national,lm75";
> + reg = <0x4d>;
> + };
> +};
> +
> +&i2c2 {
> + status = "okay";
> +};
> +
> +&i2c3 {
> + status = "okay";
> +};
> +
> +&i2c4 {
> + status = "okay";
> +};
> +
> +&i2c5 {
> + status = "okay";
> +};
> +
> +&i2c6 {
> + status = "okay";
> + /* Slot 0,
> + * Slot 1,
> + * Slot 2,
> + * Slot 3
> + */
> +
> + i2c-switch at 70 {
> + compatible = "nxp,pca9545";
> + reg = <0x70>;
> + #address-cells = <1>;
> + #size-cells = <0>;
> + i2c-mux-idle-disconnect; /* may use mux at 70 next. */
It's fine to leave mux-idle-disconnect, however the two muxes you're
worried about aren't competing under the same bus. This one lives
under i2c6 and the other i2c7, so they shouldn't interfere with each
other. Does that make sense? I missed this before because the window
only let me see part of a thing so I didn't see both in the same view
until I opened the patch in patchworks.
> +
> + i2c_rbp: i2c at 0 {
> + #address-cells = <1>;
> + #size-cells = <0>;
> + reg = <0>;
> + };
> +
> + i2c_fbp1: i2c at 1 {
> + #address-cells = <1>;
> + #size-cells = <0>;
> + reg = <1>;
> + };
> +
> + i2c_fbp2: i2c at 2 {
> + #address-cells = <1>;
> + #size-cells = <0>;
> + reg = <2>;
> + };
> +
> + i2c_fbp3: i2c at 3 {
> + #address-cells = <1>;
> + #size-cells = <0>;
> + reg = <3>;
> + };
> + };
> +};
> +
> +&i2c7 {
> + status = "okay";
> +
> + /* Slot 0,
> + * Slot 1,
> + * Slot 2,
> + * Slot 3
> + */
> + i2c-switch at 76 {
> + compatible = "nxp,pca9546";
> + reg = <0x76>;
> + #address-cells = <1>;
> + #size-cells = <0>;
> + i2c-mux-idle-disconnect; /* may use mux at 76 next. */
> +
> + i2c_riser2: i2c at 0 {
> + #address-cells = <1>;
> + #size-cells = <0>;
> + reg = <0>;
> + };
> +
> + i2c_pcie4: i2c at 1 {
> + #address-cells = <1>;
> + #size-cells = <0>;
> + reg = <1>;
> + };
> +
> + i2c_riser1: i2c at 2 {
> + #address-cells = <1>;
> + #size-cells = <0>;
> + reg = <2>;
> + };
> +
> + i2c_ocp: i2c at 3 {
> + #address-cells = <1>;
> + #size-cells = <0>;
> + reg = <3>;
> + };
> + };
> +};
> +
> +&i2c8 {
> + status = "okay";
> +
> + eeprom at 57 {
> + compatible = "atmel,24c256";
> + reg = <0x57>;
> + pagesize = <16>;
> + };
> +};
> +
> +&i2c9 {
> + status = "okay";
> +};
> +
> +&i2c10 {
> + status = "okay";
> +};
> +
> +&i2c11 {
> + status = "okay";
> +};
> +
> +&i2c12 {
> + status = "okay";
> +};
> +
> +/*
> + * Enable port A as device (via the virtual hub) and port B as
> + * host by default on the eval board. This can be easily changed
> + * by replacing the override below with &ehci0 { ... } to enable
> + * host on both ports.
> + */
> +&vhub {
> + status = "okay";
> +};
> +
> +&ehci1 {
> + status = "okay";
> +};
> +
> +&uhci {
> + status = "okay";
> +};
> +
> +&gfx {
> + status = "okay";
> + memory-region = <&gfx_memory>;
> +};
> +
> +&pwm_tacho {
> + status = "okay";
> + pinctrl-names = "default";
> + pinctrl-0 = <&pinctrl_pwm0_default
> + &pinctrl_pwm1_default
> + &pinctrl_pwm2_default
> + &pinctrl_pwm3_default
> + &pinctrl_pwm4_default
> + &pinctrl_pwm5_default
> + &pinctrl_pwm6_default>;
> +
> + fan at 0 {
> + reg = <0x00>;
> + aspeed,fan-tach-ch = /bits/ 8 <0x00>;
> + };
> +
> + fan at 1 {
> + reg = <0x00>;
> + aspeed,fan-tach-ch = /bits/ 8 <0x01>;
> + };
> +
> + fan at 2 {
> + reg = <0x01>;
> + aspeed,fan-tach-ch = /bits/ 8 <0x02>;
> + };
> +
> + fan at 3 {
> + reg = <0x01>;
> + aspeed,fan-tach-ch = /bits/ 8 <0x03>;
> + };
> +
> + fan at 4 {
> + reg = <0x02>;
> + aspeed,fan-tach-ch = /bits/ 8 <0x04>;
> + };
> +
> + fan at 5 {
> + reg = <0x02>;
> + aspeed,fan-tach-ch = /bits/ 8 <0x05>;
> + };
> +
> + fan at 6 {
> + reg = <0x03>;
> + aspeed,fan-tach-ch = /bits/ 8 <0x06>;
> + };
> +
> + fan at 7 {
> + reg = <0x03>;
> + aspeed,fan-tach-ch = /bits/ 8 <0x07>;
> + };
> +
> + fan at 8 {
> + reg = <0x04>;
> + aspeed,fan-tach-ch = /bits/ 8 <0x08>;
> + };
> +
> + fan at 9 {
> + reg = <0x04>;
> + aspeed,fan-tach-ch = /bits/ 8 <0x09>;
> + };
> +
> + fan at 10 {
> + reg = <0x05>;
> + aspeed,fan-tach-ch = /bits/ 8 <0x0a>;
> + };
> +
> + fan at 11 {
> + reg = <0x05>;
> + aspeed,fan-tach-ch = /bits/ 8 <0x0b>;
> + };
> +
> + fan at 12 {
> + reg = <0x06>;
> + aspeed,fan-tach-ch = /bits/ 8 <0x0c>;
> + };
> +
> + fan at 13 {
> + reg = <0x06>;
> + aspeed,fan-tach-ch = /bits/ 8 <0x0d>;
> + };
> +};
> +
> +&gpio {
> +
> + pin_gpio_a0 {
> + gpio-hog;
> + gpios = <ASPEED_GPIO(A, 0) GPIO_ACTIVE_HIGH>;
> + input;
> + line-name = "MAC1_INT_N";
> + };
> +
> + pin_gpio_a1 {
> + gpio-hog;
> + gpios = <ASPEED_GPIO(A, 1) GPIO_ACTIVE_HIGH>;
> + input;
> + line-name = "MEZZ_C_PRESENT_N";
> + };
> +
> + pin_gpio_a2 {
> + gpio-hog;
> + gpios = <ASPEED_GPIO(A, 2) GPIO_ACTIVE_HIGH>;
> + input;
> + line-name = "PSU1_PRST";
> + };
> +
> + pin_gpio_a3 {
> + gpio-hog;
> + gpios = <ASPEED_GPIO(A, 3) GPIO_ACTIVE_HIGH>;
> + input;
> + line-name = "PSU2_PRST";
> + };
> +
> + pin_gpio_b5 {
> + gpio-hog;
> + gpios = <ASPEED_GPIO(B, 5) GPIO_ACTIVE_HIGH>;
> + output-high;
> + line-name = "IRQ_BMC_PCH_SMI_LPC_N";
> + };
> +
> + pin_gpio_f0 {
> + gpio-hog;
> + gpios = <ASPEED_GPIO(F, 0) GPIO_ACTIVE_HIGH>;
> + output-low;
> + line-name = "IRQ_BMC_PCH_NMI_R";
> + };
> +
> + pin_gpio_f1 {
> + gpio-hog;
> + gpios = <ASPEED_GPIO(F, 1) GPIO_ACTIVE_HIGH>;
> + input;
> + line-name = "FM_CPU1_DISABLE_COD_N";
> + };
> +
> + pin_gpio_f2 {
> + gpio-hog;
> + gpios = <ASPEED_GPIO(F, 2) GPIO_ACTIVE_HIGH>;
> + input;
> + line-name = "SMB_LAN_ALERT_N_MEZZ";
> + };
> +
> + pin_gpio_f3 {
> + gpio-hog;
> + gpios = <ASPEED_GPIO(F, 3) GPIO_ACTIVE_HIGH>;
> + output-high;
> + line-name = "I2C_BUS0_RST_OUT_N";
> + };
> +
> + pin_gpio_f4 {
> + gpio-hog;
> + gpios = <ASPEED_GPIO(F, 4) GPIO_ACTIVE_HIGH>;
> + output-low;
> + line-name = "FM_SKT0_FAULT_LED";
> + };
> +
> + pin_gpio_f5 {
> + gpio-hog;
> + gpios = <ASPEED_GPIO(F, 5) GPIO_ACTIVE_HIGH>;
> + output-low;
> + line-name = "FM_SKT1_FAULT_LED";
> + };
> +
> + pin_gpio_f6 {
> + gpio-hog;
> + gpios = <ASPEED_GPIO(F, 6) GPIO_ACTIVE_HIGH>;
> + input;
> + line-name = "IRQ_BMC_CPLD_NMI";
> + };
> +
> + pin_gpio_f7 {
> + gpio-hog;
> + gpios = <ASPEED_GPIO(F, 7) GPIO_ACTIVE_HIGH>;
> + input;
> + line-name = "PSU2_ALERT_N";
> + };
> +
> + pin_gpio_g0 {
> + gpio-hog;
> + gpios = <ASPEED_GPIO(G, 0) GPIO_ACTIVE_HIGH>;
> + input;
> + line-name = "FM_CPU_ERR2_LVT3_N";
> + };
> +
> + pin_gpio_g1 {
> + gpio-hog;
> + gpios = <ASPEED_GPIO(G, 1) GPIO_ACTIVE_HIGH>;
> + input;
> + line-name = "FM_CPU_MSMI_CATERR_LVT3_N";
> + };
> +
> + pin_gpio_g2 {
> + gpio-hog;
> + gpios = <ASPEED_GPIO(G, 2) GPIO_ACTIVE_HIGH>;
> + input;
> + line-name = "FM_PCH_BMC_THERMTRIP_N";
> + };
> +
> + pin_gpio_g3 {
> + gpio-hog;
> + gpios = <ASPEED_GPIO(G, 3) GPIO_ACTIVE_HIGH>;
> + input;
> + line-name = "BMC_I2C_BUS7_INT_N";
> + };
> +
> + pin_gpio_g4 {
> + gpio-hog;
> + gpios = <ASPEED_GPIO(G, 4) GPIO_ACTIVE_HIGH>;
> + output-high;
> + line-name = "FAN_PWR_CTL_N";
> + };
> +
> + pin_gpio_g5 {
> + gpio-hog;
> + gpios = <ASPEED_GPIO(G, 5) GPIO_ACTIVE_HIGH>;
> + input;
> + line-name = "NFC_FD_N";
> + };
> +
> + pin_gpio_g6 {
> + gpio-hog;
> + gpios = <ASPEED_GPIO(G, 6) GPIO_ACTIVE_HIGH>;
> + input;
> + line-name = "IRQ_NMI_EVENT_N";
> + };
> +
> + pin_gpio_g7 {
> + gpio-hog;
> + gpios = <ASPEED_GPIO(G, 7) GPIO_ACTIVE_HIGH>;
> + output-high;
> + line-name = "RST_BMC_PCIE_I2CMUX_N";
> + };
> +
> + pin_gpio_h0 {
> + gpio-hog;
> + gpios = <ASPEED_GPIO(H, 0) GPIO_ACTIVE_HIGH>;
> + input;
> + line-name = "PSU1_EPOW_N_R";
> + };
> +
> + pin_gpio_h1 {
> + gpio-hog;
> + gpios = <ASPEED_GPIO(H, 1) GPIO_ACTIVE_HIGH>;
> + input;
> + line-name = "PSU2_EPOW_N_R";
> + };
> +
> + pin_gpio_h2 {
> + gpio-hog;
> + gpios = <ASPEED_GPIO(H, 2) GPIO_ACTIVE_HIGH>;
> + output-high;
> + line-name = "PSU1_FFS_N_R";
> + };
> +
> + pin_gpio_h3 {
> + gpio-hog;
> + gpios = <ASPEED_GPIO(H, 3) GPIO_ACTIVE_HIGH>;
> + output-high;
> + line-name = "PSU2_FFS_N_R";
> + };
> +
> + pin_gpio_h4 {
> + gpio-hog;
> + gpios = <ASPEED_GPIO(H, 4) GPIO_ACTIVE_HIGH>;
> + input;
> + line-name = "PSU1_THROTTLE_N_R";
> + };
> +
> + pin_gpio_h5 {
> + gpio-hog;
> + gpios = <ASPEED_GPIO(H, 5) GPIO_ACTIVE_HIGH>;
> + input;
> + line-name = "PSU2_THROTTLE_N_R";
> + };
> +
> + pin_gpio_h6 {
> + gpio-hog;
> + gpios = <ASPEED_GPIO(H, 6) GPIO_ACTIVE_HIGH>;
> + input;
> + line-name = "PSU1_SMB_RESET_N";
> + };
> +
> + pin_gpio_h7 {
> + gpio-hog;
> + gpios = <ASPEED_GPIO(H, 7) GPIO_ACTIVE_HIGH>;
> + input;
> + line-name = "PSU2_SMB_RESET_N";
> + };
> +
> + pin_gpio_i1 {
> + gpio-hog;
> + gpios = <ASPEED_GPIO(I, 1) GPIO_ACTIVE_HIGH>;
> + input;
> + line-name = "FP_PWR_BTN_N";
> + };
> +
> + pin_gpio_i2 {
> + gpio-hog;
> + gpios = <ASPEED_GPIO(I, 2) GPIO_ACTIVE_HIGH>;
> + input;
> + line-name = "BIOS_RCVR_N";
> + };
> +
> + pin_gpio_i3 {
> + gpio-hog;
> + gpios = <ASPEED_GPIO(I, 3) GPIO_ACTIVE_HIGH>;
> + output-high;
> + line-name = "BMC_INTRUDED_COVER";
> + };
> +
> + pin_gpio_j2 {
> + gpio-hog;
> + gpios = <ASPEED_GPIO(J, 2) GPIO_ACTIVE_HIGH>;
> + output-high;
> + line-name = "BMC_BIOS_UPDATE_N";
> + };
> +
> + pin_gpio_j3 {
> + gpio-hog;
> + gpios = <ASPEED_GPIO(J, 3) GPIO_ACTIVE_HIGH>;
> + output-high;
> + line-name = "RST_BMC_HDD_I2CMUX_N";
> + };
> +
> + pin_gpio_q4 {
> + gpio-hog;
> + gpios = <ASPEED_GPIO(Q, 4) GPIO_ACTIVE_HIGH>;
> + input;
> + line-name = "MEZZ_A_PRESENT_N";
> + };
> +
> + pin_gpio_q5 {
> + gpio-hog;
> + gpios = <ASPEED_GPIO(Q, 5) GPIO_ACTIVE_HIGH>;
> + input;
> + line-name = "VGA_FRONT_PRES_N";
> + };
> +
> + pin_gpio_q6 {
> + gpio-hog;
> + gpios = <ASPEED_GPIO(Q, 6) GPIO_ACTIVE_HIGH>;
> + input;
> + line-name = "I2C_RISER1_INT_N";
> + };
> +
> + pin_gpio_q7 {
> + gpio-hog;
> + gpios = <ASPEED_GPIO(Q, 7) GPIO_ACTIVE_HIGH>;
> + input;
> + line-name = "NCSI_CABLE_DET_N";
> + };
> +
> + pin_gpio_r0 {
> + gpio-hog;
> + gpios = <ASPEED_GPIO(R, 0) GPIO_ACTIVE_HIGH>;
> + input;
> + line-name = "FP_RST_BTN_N";
> + };
> +
> + pin_gpio_r2 {
> + gpio-hog;
> + gpios = <ASPEED_GPIO(R, 2) GPIO_ACTIVE_HIGH>;
> + input;
> + line-name = "HDDSIG1_DETECT_N";
> + };
> +
> + pin_gpio_r3 {
> + gpio-hog;
> + gpios = <ASPEED_GPIO(R, 3) GPIO_ACTIVE_HIGH>;
> + input;
> + line-name = "HDDSIG2_DETECT_N";
> + };
> +
> + pin_gpio_r4 {
> + gpio-hog;
> + gpios = <ASPEED_GPIO(R, 4) GPIO_ACTIVE_HIGH>;
> + input;
> + line-name = "HDDSIG3_DETECT_N";
> + };
> +
> + pin_gpio_r5 {
> + gpio-hog;
> + gpios = <ASPEED_GPIO(R, 5) GPIO_ACTIVE_HIGH>;
> + input;
> + line-name = "VIDEO_CABLE_DETECT_N";
> + };
> +
> + pin_gpio_s0 {
> + gpio-hog;
> + gpios = <ASPEED_GPIO(S, 0) GPIO_ACTIVE_HIGH>;
> + input;
> + line-name = "BMC_PS_RAPIDON_WAKE_R_N";
> + };
> +
> + pin_gpio_s1 {
> + gpio-hog;
> + gpios = <ASPEED_GPIO(S, 1) GPIO_ACTIVE_HIGH>;
> + input;
> + line-name = "HOST_TPM_PP_BUF";
> + };
> +
> + pin_gpio_s2 {
> + gpio-hog;
> + gpios = <ASPEED_GPIO(S, 2) GPIO_ACTIVE_HIGH>;
> + output-high;
> + line-name = "BMC_VGA_SW";
> + };
> +
> + pin_gpio_s3 {
> + gpio-hog;
> + gpios = <ASPEED_GPIO(S, 3) GPIO_ACTIVE_HIGH>;
> + input;
> + line-name = "IRQ_SML0_ALERT_MUX_N";
> + };
> +
> + pin_gpio_s4 {
> + gpio-hog;
> + gpios = <ASPEED_GPIO(S, 4) GPIO_ACTIVE_HIGH>;
> + output;
> + line-name = "VBAT_EN_N";
> + };
> +
> + pin_gpio_s5 {
> + gpio-hog;
> + gpios = <ASPEED_GPIO(S, 5) GPIO_ACTIVE_HIGH>;
> + input;
> + line-name = "BMC_HW_STRAP_4";
> + };
> +
> + pin_gpio_s6 {
> + gpio-hog;
> + gpios = <ASPEED_GPIO(S, 6) GPIO_ACTIVE_HIGH>;
> + output-high;
> + line-name = "PU_BMC_GPIOS6";
> + };
> +
> + pin_gpio_s7 {
> + gpio-hog;
> + gpios = <ASPEED_GPIO(S, 7) GPIO_ACTIVE_HIGH>;
> + input;
> + line-name = "I2C_BUS7_RESET_N";
> + };
> +
> + pin_gpio_y0 {
> + gpio-hog;
> + gpios = <ASPEED_GPIO(Y, 0) GPIO_ACTIVE_HIGH>;
> + output-low;
> + line-name = "BMC_NCSI_MUX_CTL_S0";
> + };
> +
> + pin_gpio_y1 {
> + gpio-hog;
> + gpios = <ASPEED_GPIO(Y, 1) GPIO_ACTIVE_HIGH>;
> + output-low;
> + line-name = "BMC_NCSI_MUX_CTL_S1";
> + };
> +
> + pin_gpio_y2 {
> + gpio-hog;
> + gpios = <ASPEED_GPIO(Y, 2) GPIO_ACTIVE_HIGH>;
> + input;
> + line-name = "UID_ALERT_N";
> + };
> +
> + pin_gpio_z0 {
> + gpio-hog;
> + gpios = <ASPEED_GPIO(Z, 0) GPIO_ACTIVE_HIGH>;
> + output-high;
> + line-name = "I2C_RISER2_INT_N";
> + };
> +
> + pin_gpio_z2 {
> + gpio-hog;
> + gpios = <ASPEED_GPIO(Z, 2) GPIO_ACTIVE_HIGH>;
> + output-high;
> + line-name = "I2C_RISER2_RESET_N";
> + };
> +
> + pin_gpio_z3 {
> + gpio-hog;
> + gpios = <ASPEED_GPIO(Z, 3) GPIO_ACTIVE_HIGH>;
> + output-high;
> + line-name = "FM_BMC_PCH_SCI_LPC_N";
> + };
> +
> + pin_gpio_z4 {
> + gpio-hog;
> + gpios = <ASPEED_GPIO(Z, 4) GPIO_ACTIVE_HIGH>;
> + input;
> + line-name = "BMC_HW_STRAP_17";
> + };
> +
> + pin_gpio_z6 {
> + gpio-hog;
> + gpios = <ASPEED_GPIO(Z, 6) GPIO_ACTIVE_HIGH>;
> + input;
> + line-name = "BMC_HW_STRAP_20";
> + };
> +
> + pin_gpio_z7 {
> + gpio-hog;
> + gpios = <ASPEED_GPIO(Z, 7) GPIO_ACTIVE_HIGH>;
> + output-low;
> + line-name = "BMC_POST_CMPLT_N";
> + };
> +
> + pin_gpio_aa0 {
> + gpio-hog;
> + gpios = <ASPEED_GPIO(AA, 0) GPIO_ACTIVE_HIGH>;
> + output-low;
> + line-name = "HOST_BMC_USB_SEL";
> + };
> +
> + pin_gpio_aa1 {
> + gpio-hog;
> + gpios = <ASPEED_GPIO(AA, 1) GPIO_ACTIVE_HIGH>;
> + input;
> + line-name = "PSU1_ALERT_N";
> + };
> +
> + pin_gpio_aa2 {
> + gpio-hog;
> + gpios = <ASPEED_GPIO(AA, 2) GPIO_ACTIVE_HIGH>;
> + input;
> + line-name = "FM_PVCCIN_CPU0_PWR_IN_ALERT_N";
> + };
> +
> + pin_gpio_aa3 {
> + gpio-hog;
> + gpios = <ASPEED_GPIO(AA, 3) GPIO_ACTIVE_HIGH>;
> + input;
> + line-name = "FM_PVCCIN_CPU1_PWR_IN_ALERT_N";
> + };
> +
> + pin_gpio_aa4 {
> + gpio-hog;
> + gpios = <ASPEED_GPIO(AA, 4) GPIO_ACTIVE_HIGH>;
> + input;
> + line-name = "USB_CABLE_DETECT_N";
> + };
> +
> + pin_gpio_aa5 {
> + gpio-hog;
> + gpios = <ASPEED_GPIO(AA, 5) GPIO_ACTIVE_HIGH>;
> + output-high;
> + line-name = "I2C_BUS1_RST_OUT_N";
> + };
> +
> + pin_gpio_aa6 {
> + gpio-hog;
> + gpios = <ASPEED_GPIO(AA, 6) GPIO_ACTIVE_HIGH>;
> + input;
> + line-name = "IRQ_SMI_ACTIVE_N";
> + };
> +
> + pin_gpio_aa7 {
> + gpio-hog;
> + gpios = <ASPEED_GPIO(AA, 7) GPIO_ACTIVE_HIGH>;
> + input;
> + line-name = "FM_BIOS_POST_CMPLT_N";
> + };
> +
> + pin_gpio_ab0 {
> + gpio-hog;
> + gpios = <ASPEED_GPIO(AB, 0) GPIO_ACTIVE_HIGH>;
> + input;
> + line-name = "FM_TPM_MOD_PRES_N";
> + };
> +
> + pin_gpio_ab1 {
> + gpio-hog;
> + gpios = <ASPEED_GPIO(AB, 1) GPIO_ACTIVE_HIGH>;
> + input;
> + line-name = "FORCE_NMI_SW_FPGA_N";
> + };
> +
> + pin_gpio_ab2 {
> + gpio-hog;
> + gpios = <ASPEED_GPIO(AB, 2) GPIO_ACTIVE_HIGH>;
> + input;
> + line-name = "1U_2U_PCBA_SEL_R";
> + };
> +
> + pin_gpio_ab3 {
> + gpio-hog;
> + gpios = <ASPEED_GPIO(AB, 3) GPIO_ACTIVE_HIGH>;
> + input;
> + line-name = "INTRUDED_PRES_N";
> + };
> +};
This is my last comment.
Thanks,
Patrick
> --
> 2.7.4
>
More information about the openbmc
mailing list