[PATCH v3 1/2] hwmon: (adm1275): Allow setting shunt reg value

[Kun Yi]

On Sat, Oct 27, 2018 at 10:28 AM Guenter Roeck <linux at roeck-us.net> wrote:
>
> On Wed, Oct 17, 2018 at 03:26:39PM -0700, Kun Yi wrote:
> > The ADM series of hotswap controllers support extending
> > the current measurement range by using a sensing resistor
> > value other than the typical 1 mOhm. For example, using a 0.5 mOhm
> > sensing resistor doubles the maximal current can be measured.
> >
> > Current driver assumes a shunt resistor value of 1 mOhm in calculation,
> > meaning for other resistor values, hwmon will report scaled
> > current/power measurements. This patch parses device tree parameter
> > "shunt-resistor-micro-ohms", if there is one.
> >
> > Signed-off-by: Kun Yi <kunyi at google.com>
>
> Applied to hwmon-next.
>
> Thanks,
> Guenter
>
> > ---
> > Changes in v3:
> > - splitted hwmon and device tree binding patches
> >
> >  Documentation/hwmon/adm1275   |  3 +++
> >  drivers/hwmon/pmbus/adm1275.c | 15 +++++++++++++--
> >  2 files changed, 16 insertions(+), 2 deletions(-)
> >
> > diff --git a/Documentation/hwmon/adm1275 b/Documentation/hwmon/adm1275
> > index 39033538eb03..5e277b0d91ce 100644
> > --- a/Documentation/hwmon/adm1275
> > +++ b/Documentation/hwmon/adm1275
> > @@ -58,6 +58,9 @@ The ADM1075, unlike many other PMBus devices, does not support internal voltage
> >  or current scaling. Reported voltages, currents, and power are raw measurements,
> >  and will typically have to be scaled.
> >
> > +The shunt value in micro-ohms can be set via device tree at compile-time. Please
> > +refer to the Documentation/devicetree/bindings/hwmon/adm1275.txt for bindings
> > +if the device tree is used.
> >
> >  Platform data support
> >  ---------------------
> > diff --git a/drivers/hwmon/pmbus/adm1275.c b/drivers/hwmon/pmbus/adm1275.c
> > index 13600fa79e7f..f569372c9204 100644
> > --- a/drivers/hwmon/pmbus/adm1275.c
> > +++ b/drivers/hwmon/pmbus/adm1275.c
> > @@ -373,6 +373,7 @@ static int adm1275_probe(struct i2c_client *client,
> >       const struct coefficients *coefficients;
> >       int vindex = -1, voindex = -1, cindex = -1, pindex = -1;
> >       int tindex = -1;
> > +     u32 shunt;
> >
> >       if (!i2c_check_functionality(client->adapter,
> >                                    I2C_FUNC_SMBUS_READ_BYTE_DATA
> > @@ -421,6 +422,13 @@ static int adm1275_probe(struct i2c_client *client,
> >       if (!data)
> >               return -ENOMEM;
> >
> > +     if (of_property_read_u32(client->dev.of_node,
> > +                              "shunt-resistor-micro-ohms", &shunt))
> > +             shunt = 1000; /* 1 mOhm if not set via DT */
> > +
> > +     if (shunt == 0)
> > +             return -EINVAL;
> > +
> >       data->id = mid->driver_data;
> >
> >       info = &data->info;
> > @@ -654,12 +662,15 @@ static int adm1275_probe(struct i2c_client *client,
> >               info->R[PSC_VOLTAGE_OUT] = coefficients[voindex].R;
> >       }
> >       if (cindex >= 0) {
> > -             info->m[PSC_CURRENT_OUT] = coefficients[cindex].m;
> > +             /* Scale current with sense resistor value */
> > +             info->m[PSC_CURRENT_OUT] =
> > +                     coefficients[cindex].m * shunt / 1000;
> >               info->b[PSC_CURRENT_OUT] = coefficients[cindex].b;
> >               info->R[PSC_CURRENT_OUT] = coefficients[cindex].R;
> >       }
> >       if (pindex >= 0) {
> > -             info->m[PSC_POWER] = coefficients[pindex].m;
> > +             info->m[PSC_POWER] =
> > +                     coefficients[pindex].m * shunt / 1000;
> >               info->b[PSC_POWER] = coefficients[pindex].b;
> >               info->R[PSC_POWER] = coefficients[pindex].R;
> >       }

Thanks!

-- 
Regards,
Kun