Temperature Sensor Reading not showing up.
AKASH G J
akashgj91 at gmail.com
Thu Nov 8 17:26:57 AEDT 2018
Actually the I2C address mentioned in board schematics is 0x90. When I gave
that in device tree file, it is showing the following error message.
i2c i2c-12: Invalid 7 bit I2C address 0x90
i2c i2c-12: of_i2c: Failure registering /ahb/apb/i2c1e78a000/i2c-bus at 440
/tmp75 at 90
i2c i2c-12: of_i2c: Failed to create I2C device for
/ahb/apb/i2c1e78a000/i2c-bus at 440/tmp75 at 90
So I took first 7 MSB bits 0f 0x90, that is 0x48 and I used that in device
tree file.
Following is the content of dmesg.
[ 0.000000] Booting Linux on physical CPU 0x0
[ 0.000000] Linux version
4.18.7-b7ba2a0af62b835fb3cac7bd3bbc72dcb1955b65 (oe-user at oe-host) (gcc
version 7.3.0 (GCC)) #1 Thu Nov 8 06:06:20 UTC 2018
[ 0.000000] CPU: ARMv6-compatible processor [410fb767] revision 7
(ARMv7), cr=00c5387d
[ 0.000000] CPU: PIPT / VIPT nonaliasing data cache, VIPT nonaliasing
instruction cache
[ 0.000000] OF: fdt: Machine model: Zaius BMC
[ 0.000000] Memory policy: Data cache writeback
[ 0.000000] cma: Reserved 16 MiB at 0x9cc00000
[ 0.000000] On node 0 totalpages: 110592
[ 0.000000] Normal zone: 992 pages used for memmap
[ 0.000000] Normal zone: 0 pages reserved
[ 0.000000] Normal zone: 110592 pages, LIFO batch:31
[ 0.000000] random: get_random_bytes called from start_kernel+0x8c/0x4b4
with crng_init=0
[ 0.000000] pcpu-alloc: s0 r0 d32768 u32768 alloc=1*32768
[ 0.000000] pcpu-alloc: [0] 0
[ 0.000000] Built 1 zonelists, mobility grouping on. Total pages: 109600
[ 0.000000] Kernel command line: console=ttyS4,115200n8 root=/dev/ram rw
[ 0.000000] Dentry cache hash table entries: 65536 (order: 6, 262144
bytes)
[ 0.000000] Inode-cache hash table entries: 32768 (order: 5, 131072
bytes)
[ 0.000000] Memory: 396452K/442368K available (6144K kernel code, 373K
rwdata, 1208K rodata, 1024K init, 143K bss, 29532K reserved, 16384K
cma-reserved)
[ 0.000000] Virtual kernel memory layout:
[ 0.000000] vector : 0xffff0000 - 0xffff1000 ( 4 kB)
[ 0.000000] fixmap : 0xffc00000 - 0xfff00000 (3072 kB)
[ 0.000000] vmalloc : 0x9f800000 - 0xff800000 (1536 MB)
[ 0.000000] lowmem : 0x80000000 - 0x9f000000 ( 496 MB)
[ 0.000000] .text : 0x(ptrval) - 0x(ptrval) (7136 kB)
[ 0.000000] .init : 0x(ptrval) - 0x(ptrval) (1024 kB)
[ 0.000000] .data : 0x(ptrval) - 0x(ptrval) ( 374 kB)
[ 0.000000] .bss : 0x(ptrval) - 0x(ptrval) ( 144 kB)
[ 0.000000] ftrace: allocating 19300 entries in 57 pages
[ 0.000000] NR_IRQS: 16, nr_irqs: 16, preallocated irqs: 16
[ 0.000000] i2c controller registered, irq 16
[ 0.000000] clocksource: FTTMR010-TIMER2: mask: 0xffffffff max_cycles:
0xffffffff, max_idle_ns: 77222644334 ns
[ 0.000017] sched_clock: 32 bits at 24MHz, resolution 40ns, wraps every
86767015915ns
[ 0.000085] Switching to timer-based delay loop, resolution 40ns
[ 0.001073] Calibrating delay loop (skipped), value calculated using
timer frequency.. 49.50 BogoMIPS (lpj=247500)
[ 0.001125] pid_max: default: 32768 minimum: 301
[ 0.001802] Mount-cache hash table entries: 1024 (order: 0, 4096 bytes)
[ 0.001843] Mountpoint-cache hash table entries: 1024 (order: 0, 4096
bytes)
[ 0.003239] CPU: Testing write buffer coherency: ok
[ 0.004862] Setting up static identity map for 0x80100000 - 0x80100038
[ 0.009381] devtmpfs: initialized
[ 0.024442] clocksource: jiffies: mask: 0xffffffff max_cycles:
0xffffffff, max_idle_ns: 19112604462750000 ns
[ 0.024495] futex hash table entries: 256 (order: -1, 3072 bytes)
[ 0.027637] pinctrl core: initialized pinctrl subsystem
[ 0.028592] NET: Registered protocol family 16
[ 0.031007] DMA: preallocated 256 KiB pool for atomic coherent
allocations
[ 0.033079] hw-breakpoint: found 6 breakpoint and 1 watchpoint registers.
[ 0.033111] hw-breakpoint: maximum watchpoint size is 4 bytes.
[ 0.130549] usbcore: registered new interface driver usbfs
[ 0.130740] usbcore: registered new interface driver hub
[ 0.130947] usbcore: registered new device driver usb
[ 0.141551] clocksource: Switched to clocksource FTTMR010-TIMER2
[ 0.184913] NET: Registered protocol family 2
[ 0.186058] tcp_listen_portaddr_hash hash table entries: 512 (order: 0,
4096 bytes)
[ 0.186138] TCP established hash table entries: 4096 (order: 2, 16384
bytes)
[ 0.186226] TCP bind hash table entries: 4096 (order: 2, 16384 bytes)
[ 0.186320] TCP: Hash tables configured (established 4096 bind 4096)
[ 0.186539] UDP hash table entries: 256 (order: 0, 4096 bytes)
[ 0.186597] UDP-Lite hash table entries: 256 (order: 0, 4096 bytes)
[ 0.186965] NET: Registered protocol family 1
[ 0.189270] Unpacking initramfs...
[ 19.439065] Freeing initrd memory: 15708K
[ 19.446805] workingset: timestamp_bits=30 max_order=17 bucket_order=0
[ 19.447297] squashfs: version 4.0 (2009/01/31) Phillip Lougher
[ 19.447335] jffs2: version 2.2. (SUMMARY) �© 2001-2006 Red Hat, Inc.
[ 19.452647] NET: Registered protocol family 38
[ 19.452725] io scheduler noop registered
[ 19.452899] io scheduler cfq registered (default)
[ 19.453388] aspeed-g5-pinctrl 1e6e2000.syscon:pinctrl: could not map pin
config for "C7"
[ 19.453512] aspeed-g5-pinctrl 1e6e2000.syscon:pinctrl: could not map pin
config for "B7"
[ 19.453850] aspeed-g5-pinctrl 1e6e2000.syscon:pinctrl: pin_config_set op
failed for pin 233
[ 19.453872] gpio_aspeed 1e780000.gpio: Error applying setting, reverse
things back
[ 19.454219] GPIO line 396 (iso_u164_en) hogged as output/high
[ 19.454304] GPIO line 400 (ncsi_mux_en_n) hogged as output/low
[ 19.454372] GPIO line 401 (bmc_i2c2_sw_rst_n) hogged as output/high
[ 19.454435] GPIO line 403 (bmc_i2c5_sw_rst_n) hogged as output/high
[ 19.455906] ipmi-bt-host 1e789140.ibt: Found bt bmc device
[ 19.456944] ipmi-bt-host 1e789140.ibt: Using IRQ 32
[ 19.467271] Serial: 8250/16550 driver, 6 ports, IRQ sharing enabled
[ 19.474908] 1e787000.serial: ttyS5 at MMIO 0x1e787000 (irq = 32,
base_baud = 1546875) is a 16550A
[ 19.479132] 1e783000.serial: ttyS0 at MMIO 0x1e783000 (irq = 30,
base_baud = 1500000) is a 16550A
[ 19.481258] 1e784000.serial: ttyS4 at MMIO 0x1e784000 (irq = 31,
base_baud = 1500000) is a 16550A
[ 19.963806] console [ttyS4] enabled
[ 20.110086] timeriomem_rng 1e6e2078.hwrng: 32bits from 0x(ptrval) @ 1us
[ 20.119184] aspeed_gfx 1e6e6000.display: failed to initialize reserved
mem: -19
[ 20.136001] random: fast init done
[ 20.150290] loop: module loaded
[ 20.155637] aspeed-lpc-ctrl 1e789080.lpc-ctrl: Loaded at [mem
0x98000000-0x9bffffff flags 0x200]
[ 20.171871] aspeed-smc 1e620000.flash-controller: Using 50 MHz SPI
frequency
[ 20.179140] aspeed-smc 1e620000.flash-controller: mx25l25635e (32768
Kbytes)
[ 20.186217] aspeed-smc 1e620000.flash-controller: CE0 window [
0x20000000 - 0x22000000 ] 32MB
[ 20.194856] aspeed-smc 1e620000.flash-controller: CE1 window [
0x22000000 - 0x2a000000 ] 128MB
[ 20.203483] aspeed-smc 1e620000.flash-controller: read control register:
203b0641
[ 20.689020] 5 fixed-partitions partitions found on MTD device bmc
[ 20.695136] Creating 5 MTD partitions on "bmc":
[ 20.699685] 0x000000000000-0x000000060000 : "u-boot"
[ 20.708545] 0x000000060000-0x000000080000 : "u-boot-env"
[ 20.717721] 0x000000080000-0x0000004c0000 : "kernel"
[ 20.727542] 0x0000004c0000-0x000001c00000 : "rofs"
[ 20.737317] 0x000001c00000-0x000002000000 : "rwfs"
[ 20.749007] aspeed-smc 1e630000.flash-controller: Using 100 MHz SPI
frequency
[ 20.756392] aspeed-smc 1e630000.flash-controller: mx25l25635e (32768
Kbytes)
[ 20.763470] aspeed-smc 1e630000.flash-controller: CE0 window [
0x30000000 - 0x32000000 ] 32MB
[ 20.772110] aspeed-smc 1e630000.flash-controller: CE1 window [
0x32000000 - 0x38000000 ] 96MB
[ 20.780646] aspeed-smc 1e630000.flash-controller: read control register:
203b0241
[ 20.813318] aspeed-smc 1e630000.flash-controller: Calibration area too
uniform, using low speed
[ 20.828013] aspeed-smc 1e631000.flash-controller: Using 50 MHz SPI
frequency
[ 20.835142] aspeed-smc 1e631000.flash-controller: unrecognized JEDEC id
bytes: 00, 00, 00
[ 20.843331] aspeed-smc 1e631000.flash-controller: Aspeed SMC probe
failed -2
[ 20.858037] aspeed-smc: probe of 1e631000.flash-controller failed with
error -2
[ 20.867590] libphy: Fixed MDIO Bus: probed
[ 20.872732] ftgmac100 1e660000.ethernet: Generated random MAC address
62:0e:a0:5b:c9:d8
[ 20.880773] ftgmac100 1e660000.ethernet: Using NCSI interface
[ 20.887639] ftgmac100 1e660000.ethernet eth0: irq 19, mapped at (ptrval)
[ 20.894956] ftgmac100 1e680000.ethernet: Read MAC address
00:de:ad:be:ef:01 from chip
[ 20.922800] libphy: ftgmac100_mdio: probed
[ 20.968049] random: crng init done
[ 21.005895] Broadcom BCM54612E 1e680000.ethernet--1:01: attached PHY
driver [Broadcom BCM54612E] (mii_bus:phy_addr=1e680000.ethernet--1:01,
irq=POLL)
[ 21.020452] ftgmac100 1e680000.ethernet eth1: irq 20, mapped at 52db8149
[ 21.027520] ehci_hcd: USB 2.0 'Enhanced' Host Controller (EHCI) Driver
[ 21.034112] ehci-platform: EHCI generic platform driver
[ 21.040400] i2c /dev entries driver
[ 21.063218] aspeed-i2c-bus 1e78a040.i2c-bus: i2c bus 0 registered, irq 34
[ 21.072475] aspeed-i2c-bus 1e78a080.i2c-bus: i2c bus 1 registered, irq 35
[ 21.082579] aspeed-i2c-bus 1e78a140.i2c-bus: i2c bus 4 registered, irq 36
[ 21.092719] aspeed-i2c-bus 1e78a300.i2c-bus: i2c bus 7 registered, irq 37
[ 21.102868] aspeed-i2c-bus 1e78a340.i2c-bus: i2c bus 8 registered, irq 38
[ 21.113105] aspeed-i2c-bus 1e78a440.i2c-bus: i2c bus 12 registered, irq
39
[ 21.122370] i2c i2c-7: Added multiplexed i2c bus 215
[ 21.127366] pca9541 7-0070: registered master selector for I2C pca9541
[ 21.138262] pca954x 1-0071: probe failed
[ 21.142888] pca954x 4-0071: probe failed
[ 21.155079] pmbus 7-0061: PMBus status register not found
[ 21.165593] ucd9000 0-0064: Failed to read device ID
[ 21.173323] usbcore: registered new interface driver usbhid
[ 21.179018] usbhid: USB HID core driver
[ 21.202652] NET: Registered protocol family 10
[ 21.218129] Segment Routing with IPv6
[ 21.222653] sit: IPv6, IPv4 and MPLS over IPv4 tunneling driver
[ 21.229964] NET: Registered protocol family 17
[ 21.234478] 8021q: 802.1Q VLAN Support v1.8
[ 21.248244] console [netcon0] enabled
[ 21.251931] netconsole: network logging started
[ 21.257926] input: gpio-keys as /devices/platform/gpio-keys/input/input0
[ 21.266549] hctosys: unable to open rtc device (rtc0)
[ 21.283017] Freeing unused kernel memory: 1024K
[ 21.290261] Checked W+X mappings: passed, no W+X pages found
[ 21.390012] systemd[1]: systemd 237 running in system mode. (+PAM -AUDIT
-SELINUX -IMA -APPARMOR -SMACK +SYSVINIT -UTMP -LIBCRYPTSETUP -GCRYPT
-GNUTLS +ACL +XZ -LZ4 -SECCOMP +BLKID)
[ 21.412916] systemd[1]: Detected architecture arm.
[ 21.452208] systemd[1]: Set hostname to <zaius>.
[ 21.457517] systemd[1]: Initializing machine ID from random generator.
[ 22.750590] systemd[1]: Created slice System Slice.
[ 22.784248] systemd[1]: Created slice
system-phosphor\x2ddiscover\x2dsystem\x2dstate.slice.
[ 22.823433] systemd[1]: Listening on udev Kernel Socket.
[ 22.863473] systemd[1]: Started Dispatch Password Requests to Console
Directory Watch.
[ 22.903540] systemd[1]: Listening on Syslog Socket.
[ 22.943952] systemd[1]: Created slice
system-obmc\x2dled\x2dgroup\x2dstart.slice.
[ 24.937714] systemd-journald[501]: Received request to flush runtime
journal from PID 1
[ 28.126038] 8021q: adding VLAN 0 to HW filter on device eth0
[ 28.432290] IPv6: ADDRCONF(NETDEV_UP): eth1: link is not ready
[ 30.331771] ftgmac100 1e660000.ethernet eth0: NCSI: No channel found
with link
[ 32.674557] ftgmac100 1e680000.ethernet eth1: Link is Up - 1Gbps/Full -
flow control rx/tx
[ 32.682901] IPv6: ADDRCONF(NETDEV_CHANGE): eth1: link becomes ready
[ 34.826333] ftgmac100 1e680000.ethernet eth1: Link is Down
[ 36.988855] ftgmac100 1e680000.ethernet eth1: Link is Up - 1Gbps/Full -
flow control rx/tx
[ 39.057815] ftgmac100 1e680000.ethernet eth1: Link is Down
[ 41.254826] ftgmac100 1e680000.ethernet eth1: Link is Up - 100Mbps/Full
- flow control rx/tx
root at zaius:~# Stopping Network Time Synchronization...
[ OK ] Started Phosphor Time Manager daemon.
[ OK ] Reached target Phosphor System - Standby.
Starting Assert bmc_booted LED...
[ OK ] Reached target Power0 On (Pre).
[ OK ] Reached target Power0 On.
[ OK ] Reached target Power0 (On).
[ OK ] Started Phosphor Fan Monitor Initialization.
Starting Scan FSI devices...
[ OK ] Started Phosphor Fan Control Initialization.
[ OK ] Started Phosphor Fan Presence Tach Daemon.
[ OK ] Created slice system-phosphor\x2dfan\x2dcontrol.slice.
[ OK ] Started Phosphor Fan Control Daemon.
[ OK ] Created slice system-phosphor\x2dfan\x2dmonitor.slice.
[ OK ] Started Phosphor Fan Monitor Daemon.
[ OK ] Reached target Fan Control Ready.
[ OK ] Started Assert bmc_booted LED.
[FAILED] Failed to start Scan FSI devices.
See 'systemctl status fsi-scan at 0.service' for details.
[DEPEND] Dependency failed for Chassis0 (Power On).
[ OK ] Stopped Start chassis0 on after BMC reset.
[ OK ] Stopped target Host0 running after reset.
[ OK ] Created slice system-avsbus\x2ddisable.slice.
Starting Wait for /org/openbmc/control/chassis0...
[ OK ] Stopped target Chassis0 power on after reset.
[ OK ] Stopped target Host0 (Reset Check).
[ OK ] Created slice system-obmc\x2dled\x2dgroup\x2dstop.slice.
[ OK ] Created slice system-op\x2dpowered\x2doff.slice.
[ OK ] Stopped Check Host0 status on BMC reset.
[ OK ] Created slice system-op\x2dwait\x2dpower\x2doff.slice.
[ OK ] Created slice system-vcs\x2doff.slice.
Starting Assert power_on LED...
[ OK ] Stopped target Power0 (On).
[ OK ] Stopped target Power0 On.
[ OK ] Stopped target Power0 On (Pre).
[ OK ] Stopped Reload mboxd during power on.
[ OK ] Stopped Assert power_on LED.
[ OK ] Created slice system-op\x2dpower\x2dstop.slice.
[ OK ] Stopped target Chassis0 (Reset Check).
Starting Turn VCS rails off...
[ OK ] Created slice system-op\x2docc\x2ddisable.slice.
Starting OpenPOWER OCC Active Disable...
[ OK ] Started Wait for /org/openbmc/control/chassis0.
[FAILED] Failed to start Turn VCS rails off.
See 'systemctl status vcs-off at 0.service' for details.
[ OK ] Started Assert power_on LED.
[ OK ] Started OpenPOWER OCC Active Disable.
[ OK ] Reached target Stop Host0 (Pre).
[ OK ] Reached target Host0 (Stopping).
[ OK ] Reached target Host0 (Stopped).
[ OK ] Reached target Power0 Off (Pre).
[ OK ] Started Stop Power0.
Starting Wait for Power0 to turn off...
[ OK ] Started Wait for Power0 to turn off.
[ OK ] Started Power is off to chassis0.
[ OK ] Reached target Chassis0 (Power Off).
[ OK ] Reached target Stop Host0.
[ OK ] Reached target Power0 Off.
On Wed, Nov 7, 2018 at 12:53 AM Kun Yi <kunyi at google.com> wrote:
> Well the temp1_input not showing in sysfs is related to linux kernel, not
> with userspace. Please double check your device tree node matches physical
> bus, and the corresponding kernel configs are enabled. Attach dmesg and
> bootlog would be helpful for people to help debug.
>
> On Tue, Nov 6, 2018 at 1:53 AM AKASH G J <akashgj91 at gmail.com> wrote:
>
>> I corrected the path of the environment file to be
>> meta-zaius/recipes-phosphor/sensors/phosphor-hwmon%/obmc/hwon/ahb/apb/i2c at 1e78a000
>> /i2c-bus at 440/tmp75 at 48.conf.
>>
>> Still temp1_input is not coming on the sysfs (/sys/class/hwmon/hwmon0)
>>
>> On Tue, Nov 6, 2018 at 12:01 PM Kun Yi <kunyi at google.com> wrote:
>>
>>>
>>> On Mon, Nov 5, 2018 at 10:17 PM Troy Lee <leetroy at gmail.com> wrote:
>>>
>>>> The *service* here doesn't relate to systemd service.
>>>>
>>>> It is the name on D-Bus.
>>>> https://github.com/openbmc/phosphor-hwmon#d-bus-bus-names
>>>>
>>>> Try this command to list all the services related to hwmon:
>>>> # busctl --no-page list | grep -E "Hwmon1|PID"
>>>>
>>>> First column will be the service name.
>>>>
>>>> Yu-Ting Lee (Troy Lee) <LeeTroy at gmail.com>
>>>> AKASH G J <akashgj91 at gmail.com> 於 2018年11月5日 週一 下午4:40寫道：
>>>> >
>>>> > No such service is available in root file system. The output of the
>>>> command ls / -R | grep Hwmon is
>>>> >
>>>> > root at zaius:~# ls / -R | grep Hwmon
>>>> > xyz.openbmc_project.Hwmon at .service
>>>> > system-xyz.openbmc_project.Hwmon.slice
>>>> >
>>>> /sys/fs/cgroup/systemd/system.slice/system-xyz.openbmc_project.Hwmon.slice:
>>>> > system-xyz.openbmc_project.Hwmon.slice
>>>> >
>>>> /sys/fs/cgroup/unified/system.slice/system-xyz.openbmc_project.Hwmon.slice:
>>>> > root at zaius:~#
>>>> >
>>>> > On Mon, Nov 5, 2018 at 1:20 PM Troy Lee <leetroy at gmail.com> wrote:
>>>> >>
>>>> >> Your service path doesn't look right.
>>>> >>
>>>> >> According to:
>>>> >>
>>>> https://github.com/openbmc/docs/blob/master/sensor-architecture.md#d-bus
>>>> >>
>>>> >> It should be something like this:
>>>> >> xyz.openbmc_project.Hwmon-<hash>.Hwmon1
>>>> >>
>>>> >>
>>>> >>
>>>> >> Yu-Ting Lee (Troy Lee) <LeeTroy at gmail.com>
>>>> >> AKASH G J <akashgj91 at gmail.com> 於 2018年11月5日 週一 下午2:55寫道：
>>>> >> >
>>>> >> > I tried the command busctl --system introspect
>>>> xyz.openbmc_project.Hwmon at .service
>>>> /xyz/openbmc_project/Sensors/temperature/ambient
>>>> xyz.openbmc_project.sensor.Threshold.Warning | grep property and it outputs
>>>> >> >
>>>> >> > Failed to introspect object
>>>> /xyz/openbmc_project/Sensors/temperature/ambient of service
>>>> xyz.openbmc_project.Hwmon at .service: Invalid argument.
>>>> >> >
>>>> >> > I added the file
>>>> meta-zaius/recipes-phosphor/sensors/phosphor-hwmon%/obmc/hwmon/ahb/apb/i2c at 1e6e2000
>>>> /i2c-bus at 90/tmp75 at 48.conf in machine configuration directory with the
>>>> following contents for dbus mapping.
>>>> >> >
>>>> >> > LABEL_temp1 = ambient
>>>> >> > WARNLO_temp1=-40
>>>> >> > WARNHI_temp1=125
>>>> >> >
>>>> >> > Whether this is correct or not?
>>>> >> >
>>>> >> > On Fri, Nov 2, 2018 at 8:57 PM Emily Shaffer <
>>>> emilyshaffer at google.com> wrote:
>>>> >> >>
>>>> >> >> Have you tried a dbus introspect to see if the sensor is coming
>>>> across dbus correctly? There is a sample introspect command on the sensor
>>>> howto, check out the busctl usage.
>>>> https://github.com/openbmc/docs/blob/master/sensor-architecture.md
>>>> >> >>
>>>> >> >> On Fri, Nov 2, 2018, 3:21 AM AKASH G J <akashgj91 at gmail.com>
>>>> wrote:
>>>> >> >>>
>>>> >> >>> I added the sensor configuration to phosphor-host-ipmid's sensor
>>>> configuration like.
>>>> >> >>>
>>>> >> >>> 0x12: &temperature
>>>> >> >>> sensorType: 0x01
>>>> >> >>> path: /xyz/openbmc_project/sensors/temperature/ambient
>>>> >> >>> sensorReadingType: 0x01
>>>> >> >>> multiplierM: 235
>>>> >> >>> offsetB: 0
>>>> >> >>> bExp: 0
>>>> >> >>> unit: xyz.openbmc_project.Sensor.Value.Unit.DegreesC
>>>> >> >>> scale: -3
>>>> >> >>> rExp: -3
>>>> >> >>> serviceInterface: org.freedesktop.DBus.Properties
>>>> >> >>> readingType: readingData
>>>> >> >>> interfaces:
>>>> >> >>> xyz.openbmc_project.Sensor.Value:
>>>> >> >>> Value:
>>>> >> >>> Offsets:
>>>> >> >>> 0xFF:
>>>> >> >>> type: int64_t
>>>> >> >>>
>>>> >> >>>
>>>> >> >>> When I run the command ipmitool -I dbus sdr elist full, it gives
>>>> the following.
>>>> >> >>>
>>>> >> >>> ambient | 12h | ns | 0.0 | Disabled
>>>> >> >>>
>>>> >> >>> It is not giving the sensor reading and it is showing the sensor
>>>> device is disabled.
>>>> >> >>>
>>>> >> >>> On Thu, Nov 1, 2018 at 11:28 PM Patrick Venture <
>>>> venture at google.com> wrote:
>>>> >> >>>>
>>>> >> >>>> On Tue, Oct 30, 2018 at 10:13 PM AKASH G J <akashgj91 at gmail.com>
>>>> wrote:
>>>> >> >>>> >
>>>> >> >>>> > Hi All,
>>>> >> >>>> >
>>>> >> >>>> > I built OpenBMC Linux using Zaius configuration and booted on
>>>> BMC Aspeed AST-2500. The board we are using have one temperature sensor
>>>> (Texas Instruments TMP75) on I2C-12 interface.
>>>> >> >>>> >
>>>> >> >>>> > I added the file
>>>> meta-zaius/recipes-phosphor/sensors/phosphor-hwmon%/obmc/hwmon/ahb/apb/i2c at 1e6e2000
>>>> /i2c-bus at 90/tmp75 at 48.conf in machine configuration directory with the
>>>> following contents.
>>>> >> >>>> >
>>>> >> >>>> > LABEL_temp1 = ambient
>>>> >> >>>> > WARNLO_temp1=-40
>>>> >> >>>> > WARNHI_temp1=125
>>>> >> >>>> >
>>>> >> >>>> > I added the following patch to the kernel file
>>>> linux/arch/arm/boot/dts/aspeed-bmc-opp-zaius.dts.
>>>> >> >>>> >
>>>> >> >>>> > &i2c12 {
>>>> >> >>>> > - status = "disabled";
>>>> >> >>>> > + status = "okay";
>>>> >> >>>> > +
>>>> >> >>>> > + tmp75 at 48 {
>>>> >> >>>> > + compatible = "ti,tmp75";
>>>> >> >>>> > + reg = <0x48>;
>>>> >> >>>> > + };
>>>> >> >>>> > +
>>>> >> >>>> > };
>>>> >> >>>> >
>>>> >> >>>> > After booting Linux, the changes are reflected in
>>>> /sys/firmware/devicetree/base/ahb/apb/i2c at 1e78a000/i2c-bus at 440
>>>> /tmp75 at 48. Also,
>>>> >> >>>> > tmp78.conf is showing in
>>>> /etc/default/obmc/hwmon/ahb/apb/i2c at 1e78a000/i2c-bus at 90.
>>>>
>>>
>>> Besides what others suggested looks like you have a mismatch between
>>> your device path and the path for the environment file. They need to have
>>> the same path.
>>>
>>> Steps to try:
>>> 1. Fix the path of your environment file to be
>>> meta-zaius/recipes-phosphor/sensors/phosphor-hwmon%/obmc/hwon/ahb/apb/i2c at 1e78a000
>>> /i2c-bus at 440/tmp75 at 48.conf
>>> 2. Make sure the hwmon sysfs interface shows up and temp1_input reads a
>>> valid value
>>> 3. Play with busctl as others suggested and make sure the sensor value
>>> is reported over DBus
>>>
>>>
>>>> >> >>>> >
>>>> >> >>>> > when I am running the ipmitool command: ipmitool -I dbus sdr
>>>> elist full it is not showing the temperature sensor and its reading.
>>>> >> >>>> >
>>>> >> >>>> > Please someone help to resolve the problem.
>>>> >> >>>>
>>>> >> >>>> You'll need to add the sensor configuration to the
>>>> >> >>>> phosphor-host-ipmid's sensor configuration, see:
>>>> >> >>>>
>>>> >> >>>>
>>>> https://github.com/openbmc/openbmc/blob/master/meta-ingrasys/meta-zaius/recipes-phosphor/ipmi/phosphor-ipmi-sensor-inventory%25/config.yaml
>>>> >> >>>>
>>>> >> >>>> >
>>>> >> >>>> >
>>>> >> >>>> > Thanks and Regards,
>>>> >> >>>> >
>>>> >> >>>> > Akash
>>>> >> >>>> >
>>>>
>>>
>>>
>>> --
>>> Regards,
>>> Kun
>>>
>>
>
> --
> Regards,
> Kun
>
-------------- next part --------------
An HTML attachment was scrubbed...
URL: <http://lists.ozlabs.org/pipermail/openbmc/attachments/20181108/d7da07d7/attachment-0001.html>
More information about the openbmc
mailing list