[PATCH linux dev-4.10 3/6] mtd: spi-nor: aspeed: configure chip window on AHB bus
Cédric Le Goater
clg at kaod.org
Sat Mar 25 01:44:40 AEDT 2017
The segment registers of the SMC controller provide a way to configure
the mapping windows of the chips on the AHB bus. The settings are
required to be correct when the controller operates in Command mode,
which is the case for DMAs and the LPC mapping.
This tries to set the segment registers of each chip depending on the
size of the flash device and depending on the previous segment
settings, in order to have a contiguous window across multiple chip.
Unfortunately, the AST2500 SPI controller has a bug and it is not
possible to configure a full 128MB window for a chip of the same
size. The window size needs to be restricted to 120MB. This issue only
applies to CE0.
Sample kernel dmesg on a Witherspoon :
aspeed-smc 1e620000.flash-controller: Using IRQ 17
aspeed-smc 1e620000.flash-controller: DMA support disabled.
aspeed-smc 1e620000.flash-controller: mx25l25635e (32768 Kbytes)
aspeed-smc 1e620000.flash-controller: CE0 window [ 0x20000000- 0x22000000 ] 32MB
aspeed-smc 1e620000.flash-controller: CE1 window [ 0x22000000- 0x2a000000 ] 128MB
5 ofpart partitions found on MTD device bmc
Creating 5 MTD partitions on "bmc":
0x000000000000-0x000000060000 : "u-boot"
0x000000060000-0x000000080000 : "u-boot-env"
0x000000080000-0x0000004c0000 : "kernel"
0x0000004c0000-0x000001c00000 : "rofs"
0x000001c00000-0x000002000000 : "rwfs"
aspeed-smc 1e620000.flash-controller: mx25l25635e (32768 Kbytes)
aspeed-smc 1e620000.flash-controller: CE1 window [ 0x22000000- 0x24000000 ] 32MB
aspeed-smc 1e620000.flash-controller: CE2 window [ 0x24000000- 0x2c000000 ] 128MB
aspeed-smc 1e630000.flash-controller: mx66l1g45g (131072 Kbytes)
aspeed-smc 1e630000.flash-controller: CE0 window resized to 120MB (AST2500 HW quirk)
aspeed-smc 1e630000.flash-controller: CE0 window [ 0x30000000- 0x37800000 ] 120MB
aspeed-smc 1e630000.flash-controller: CE0 window too small for chip 128MB
aspeed-smc 1e630000.flash-controller: CE1 window [ 0x37800000- 0x38000000 ] 8MB
Signed-off-by: Cédric Le Goater <clg at kaod.org>
Acked-by: Andrew Jeffery <andrew at aj.id.au>
---
Changes since initial version :
- fixed SEGMENT_ADDR_REG()
- added some extra comments
drivers/mtd/spi-nor/aspeed-smc.c | 124 ++++++++++++++++++++++++++++++++++++++-
1 file changed, 121 insertions(+), 3 deletions(-)
diff --git a/drivers/mtd/spi-nor/aspeed-smc.c b/drivers/mtd/spi-nor/aspeed-smc.c
index b3c8cfe29765..336a1ddd100b 100644
--- a/drivers/mtd/spi-nor/aspeed-smc.c
+++ b/drivers/mtd/spi-nor/aspeed-smc.c
@@ -104,6 +104,7 @@ struct aspeed_smc_chip {
struct aspeed_smc_controller *controller;
void __iomem *ctl; /* control register */
void __iomem *ahb_base; /* base of chip window */
+ u32 ahb_window_size; /* chip window size */
unsigned long phys_base; /* physical address of window */
u32 ctl_val[smc_max]; /* control settings */
enum aspeed_smc_flash_type type; /* what type of flash */
@@ -218,6 +219,10 @@ struct aspeed_smc_controller {
#define SEGMENT_ADDR_REG0 0x30
#define SEGMENT_ADDR_START(_r) ((((_r) >> 16) & 0xFF) << 23)
#define SEGMENT_ADDR_END(_r) ((((_r) >> 24) & 0xFF) << 23)
+#define SEGMENT_ADDR_VALUE(start, end) \
+ (((((start) >> 23) & 0xFF) << 16) | ((((end) >> 23) & 0xFF) << 24))
+#define SEGMENT_ADDR_REG(controller, cs) \
+ ((controller)->regs + SEGMENT_ADDR_REG0 + (cs) * 4)
/* DMA Registers */
#define DMA_CONTROL_REG 0x80
@@ -604,8 +609,7 @@ static void __iomem *aspeed_smc_chip_base(struct aspeed_smc_chip *chip,
u32 reg;
if (controller->info->nce > 1) {
- reg = readl(controller->regs + SEGMENT_ADDR_REG0 +
- chip->cs * 4);
+ reg = readl(SEGMENT_ADDR_REG(controller, chip->cs));
if (SEGMENT_ADDR_START(reg) >= SEGMENT_ADDR_END(reg))
return NULL;
@@ -616,6 +620,111 @@ static void __iomem *aspeed_smc_chip_base(struct aspeed_smc_chip *chip,
return controller->ahb_base + offset;
}
+static u32 chip_set_segment(struct aspeed_smc_chip *chip, u32 cs, u32 start,
+ u32 size)
+{
+ struct aspeed_smc_controller *controller = chip->controller;
+ void __iomem *seg_reg;
+ u32 oldval, newval, val0, start0, end;
+
+ val0 = readl(SEGMENT_ADDR_REG(controller, 0));
+ start0 = SEGMENT_ADDR_START(val0);
+
+ seg_reg = SEGMENT_ADDR_REG(controller, cs);
+ oldval = readl(seg_reg);
+
+ /* If the chip size is not specified, use the default segment
+ * size, but take into account the possible overlap with the
+ * previous segment
+ */
+ if (!size)
+ size = SEGMENT_ADDR_END(oldval) - start;
+
+ /* The segment cannot exceed the maximum window size of the
+ * controller.
+ */
+ if (start + size > start0 + controller->info->maxsize) {
+ size = start0 + controller->info->maxsize - start;
+ dev_warn(chip->nor.dev, "CE%d window resized to %dMB",
+ cs, size >> 20);
+ }
+
+ end = start + size;
+ newval = SEGMENT_ADDR_VALUE(start, end);
+ writel(newval, seg_reg);
+
+ /* Restore default value if something goes wrong. The chip
+ * might have set some bogus value and we would loose access
+ * to the chip.
+ */
+ if (newval != readl(seg_reg)) {
+ dev_err(chip->nor.dev, "CE%d window invalid", cs);
+ writel(oldval, seg_reg);
+ start = SEGMENT_ADDR_START(oldval);
+ end = SEGMENT_ADDR_END(oldval);
+ size = end - start;
+ }
+
+ dev_info(chip->nor.dev, "CE%d window [ 0x%.8x- 0x%.8x ] %dMB",
+ cs, start, end, size >> 20);
+
+ return size;
+}
+
+/*
+ * This is expected to be called in increasing CE order
+ */
+static u32 aspeed_smc_chip_set_segment(struct aspeed_smc_chip *chip)
+{
+ struct aspeed_smc_controller *controller = chip->controller;
+ u32 val0, start0, start;
+ u32 size = chip->nor.mtd.size;
+
+ /* The AST2500 SPI controller has a bug when the CE0 chip size
+ * exceeds 120MB.
+ */
+ if (chip->cs == 0 && controller->info == &spi_2500_info &&
+ size == (128 << 20)) {
+ size = 120 << 20;
+ dev_info(chip->nor.dev,
+ "CE%d window resized to %dMB (AST2500 HW quirk)",
+ chip->cs, size >> 20);
+ }
+
+ val0 = readl(SEGMENT_ADDR_REG(controller, 0));
+ start0 = SEGMENT_ADDR_START(val0);
+
+ /* As a start address for the current segment, use the default
+ * start address if we are handling CE0 or use the previous
+ * segment ending address
+ */
+ if (chip->cs) {
+ u32 prev = readl(SEGMENT_ADDR_REG(controller, chip->cs - 1));
+
+ start = SEGMENT_ADDR_END(prev);
+ } else
+ start = start0;
+
+ size = chip_set_segment(chip, chip->cs, start, size);
+
+ /* Update chip base address on the AHB bus */
+ chip->ahb_base = controller->ahb_base + (start - start0);
+
+ if (size < chip->nor.mtd.size)
+ dev_warn(chip->nor.dev,
+ "CE%d window too small for chip %dMB",
+ chip->cs, (u32) chip->nor.mtd.size >> 20);
+
+ /* Make sure the next segment does not overlap with the
+ * current one we just configured even if there is no
+ * available chip. That could break access in Command Mode.
+ */
+ if (chip->cs < controller->info->nce - 1)
+ chip_set_segment(chip, chip->cs + 1, start + size, 0);
+
+ return size;
+}
+
static void aspeed_smc_chip_enable_write(struct aspeed_smc_chip *chip)
{
struct aspeed_smc_controller *controller = chip->controller;
@@ -689,7 +798,7 @@ static int aspeed_smc_chip_setup_init(struct aspeed_smc_chip *chip,
*/
chip->ahb_base = aspeed_smc_chip_base(chip, res);
if (!chip->ahb_base) {
- dev_warn(chip->nor.dev, "CE segment window closed.\n");
+ dev_warn(chip->nor.dev, "CE%d window closed", chip->cs);
return -EINVAL;
}
@@ -738,6 +847,15 @@ static int aspeed_smc_chip_setup_finish(struct aspeed_smc_chip *chip)
if (chip->nor.addr_width == 4 && info->set_4b)
info->set_4b(chip);
+ /* This is for direct AHB access when using Command Mode. For
+ * the AST2400 SPI controller which only handles one chip,
+ * let's use the full window.
+ */
+ if (controller->info->nce == 1)
+ chip->ahb_window_size = info->maxsize;
+ else
+ chip->ahb_window_size = aspeed_smc_chip_set_segment(chip);
+
/*
* base mode has not been optimized yet. use it for writes.
*/
--
2.7.4
More information about the openbmc
mailing list