[PATCH linux v6 16/18] drivers/fsi: Add GPIO FSI master
christopher.lee.bostic at gmail.com
christopher.lee.bostic at gmail.com
Mon Oct 31 09:09:18 AEDT 2016
From: Chris Bostic <cbostic at us.ibm.com>
Implement a FSI master using GPIO. Will generate FSI protocol for
read and write commands to particular addresses. Sends master command
and waits for and decodes a slave response. Includes Jeremy Kerr's
original GPIO master base commit.
Signed-off-by: Jeremy Kerr <jk at ozlabs.org>
---
V3 - Added remainder of base I/O ops (excluding dev tree and crc calcs).
- Add encoding of all read/write commands and send data over sda
- Check for and decode response from slave.
- Add set enable pin in master->link_enable() master specific function.
V4 - Remove unnecessary comments about delays in various locations
- Define non clock and data pins as optional and check for gpio
descriptors == NULL before accessing. Don't return error if
optional pins cannot be retrieved via devm.
- serial_in: rearrange order of msg shift and input bit OR op.
- serial_out: Fix mirror image issue on shift data out and set
data out as necessary for bit count to be sent.
- serial_out: make message parm a const
- serial_out: fix 3x 'msg & data' repeat
- poll_for_response: bits remaining was calculated with
sizeof(size) should be size.
- fsi_master_gpio_break: remove smode read
- Replace dev_info with dev_dbg in proper places.
- Add a bit count parm to serial_in, increment msg->bits
on every bit received.
- Remove magic numbers in poll_for_response that indicate
how many bits to receive
- Utilize the crc utilities to check input data and set
crc for output data
- Remove add_crc stub
V5 - Rename pins from generic 'clk', 'data', etc in dts file to
'fsi_clk', 'fsi_data', etc...
- serial_in: invert data bit during message assembly
instead of inverting whole message after assembly.
- Remove all instances of clearing out message field prior
to calling serial_in, redundant.
- Change name of build_command() to build_abs_ar_command()
to make it more obvious its creating ABS AR type commands.
- Remove unlikely( ) checks.
- Indent dev_info string "master time out waiting for response"
- poll_for_response: return FSI_GPIO_MAX busy instead of
busy_count.
- fsi_master_gpio_break: move 'logic reset' comment to above
the delay call.
- Add crc4 calculation initialization since data includes
a start bit.
V6 - Invert polarity of SDA line for start bit, echo delay, pre-
D-POLL clocking, break command sequence (pre, during, post).
- Add echo delay after sending D-POLL
- Fill in user read data with received read data response
- Clock the slave after each command completes to prime it
for another operation
- Increase D-POLL checks on BUSY response before flagging
error
- Add Alistair's crc calculator from pdbg. Having issues
with the existing one.
- Revert V5 changes to rename gpio pin names.
- Return -EIO on all bus errors
- Condense slave id and response id into one serial-in
operation
- Change D-POLL command to accommodate right alignment
- Remove all dev_info( ) calls to reduce spam
- serial_in remove cmd->bits = 0 / cmd->bits++ in for
loop. Just set value at end.
- Change v translator line to direction output once
during init and use gpiod_set_value thereafter
- Remove set/clear clocks and do it all in clock_toggle
- Fill in slave id when encoding commands. Right align
the command prior to serializing out.
- gpio master defines number of links to 1, was undefined.
---
.../devicetree/bindings/fsi-master-gpio.txt | 21 +
.../devicetree/bindings/fsi/fsi-master-gpio.txt | 21 +
arch/arm/boot/dts/aspeed-bmc-opp-palmetto.dts | 36 ++
drivers/fsi/Kconfig | 6 +
drivers/fsi/Makefile | 1 +
drivers/fsi/fsi-master-gpio.c | 522 +++++++++++++++++++++
6 files changed, 607 insertions(+)
create mode 100644 Documentation/devicetree/bindings/fsi-master-gpio.txt
create mode 100644 Documentation/devicetree/bindings/fsi/fsi-master-gpio.txt
create mode 100644 drivers/fsi/fsi-master-gpio.c
diff --git a/Documentation/devicetree/bindings/fsi-master-gpio.txt b/Documentation/devicetree/bindings/fsi-master-gpio.txt
new file mode 100644
index 0000000..d46be27
--- /dev/null
+++ b/Documentation/devicetree/bindings/fsi-master-gpio.txt
@@ -0,0 +1,21 @@
+Device-tree bindings for gpio-based FSI master driver
+-----------------------------------------------------
+
+Required properties:
+ - compatible = "ibm,fsi-master-gpio";
+ - clk-gpio;
+ - data-gpio;
+
+Optional properties:
+ - enable-gpio;
+ - trans-gpio;
+ - mux-gpio;
+
+fsi-master {
+ compatible = "ibm,fsi-master", "ibm,fsi-master-gpio";
+ clk-gpio = <&gpio 0>;
+ data-gpio = <&gpio 1>;
+ enable-gpio = <&gpio 2>; /* Enable FSI data in/out */
+ trans-gpio = <&gpio 3>; /* Voltage translator direction */
+ mux-gpio = <&gpio 4>; /* Multiplexer for FSI pins */
+}
diff --git a/Documentation/devicetree/bindings/fsi/fsi-master-gpio.txt b/Documentation/devicetree/bindings/fsi/fsi-master-gpio.txt
new file mode 100644
index 0000000..ff3a62e
--- /dev/null
+++ b/Documentation/devicetree/bindings/fsi/fsi-master-gpio.txt
@@ -0,0 +1,21 @@
+Device-tree bindings for gpio-based FSI master driver
+-----------------------------------------------------
+
+Required properties:
+ - compatible = "ibm,fsi-master-gpio";
+ - clk-gpios;
+ - data-gpios;
+
+Optional properties:
+ - enable-gpios;
+ - trans-gpios;
+ - mux-gpios;
+
+fsi-master {
+ compatible = "ibm,fsi-master", "ibm,fsi-master-gpio";
+ clk-gpios = <&gpio 0 &gpio 6>;
+ data-gpios = <&gpio 1 &gpio 7>;
+ enable-gpios = <&gpio 2 &gpio 8>; /* Enable FSI data in/out */
+ trans-gpios = <&gpio 3 &gpio 9>; /* Volts translator direction */
+ mux-gpios = <&gpio 4> &gpio 10>; /* Multiplexer for FSI pins */
+}
diff --git a/arch/arm/boot/dts/aspeed-bmc-opp-palmetto.dts b/arch/arm/boot/dts/aspeed-bmc-opp-palmetto.dts
index 21619fd..9d9c2a9 100644
--- a/arch/arm/boot/dts/aspeed-bmc-opp-palmetto.dts
+++ b/arch/arm/boot/dts/aspeed-bmc-opp-palmetto.dts
@@ -167,6 +167,42 @@
output-low;
line-name = "func_mode2";
};
+
+ pin_fsi_clk {
+ gpios = <ASPEED_GPIO(A, 4) GPIO_ACTIVE_HIGH>;
+ output-low;
+ line-name = "fsi_clk";
+ };
+
+ pin_fsi_data {
+ gpios = <ASPEED_GPIO(A, 5) GPIO_ACTIVE_HIGH>;
+ output-low;
+ line-name = "fsi_data";
+ };
+
+ pin_fsi_trans {
+ gpios = <ASPEED_GPIO(H, 6) GPIO_ACTIVE_HIGH>;
+ output-low;
+ line-name = "fsi_trans";
+ };
+
+ pin_fsi_enable {
+ gpios = <ASPEED_GPIO(D, 0) GPIO_ACTIVE_HIGH>;
+ output-low;
+ line-name = "fsi_enable";
+ };
+
+ pin_fsi_mux {
+ gpios = <ASPEED_GPIO(A, 6) GPIO_ACTIVE_HIGH>;
+ output-low;
+ line-name = "fsi_mux";
+ };
+
+ fsi_master {
+ compatible = "ibm,fsi-master", "ibm,fsi-master-gpio";
+ clk-gpios = <&gpio 0 &gpio 6>;
+ data-gpios = <&gpio 1 &gpio 7>;
+ };
};
&vuart {
diff --git a/drivers/fsi/Kconfig b/drivers/fsi/Kconfig
index f065dbe..b21fe3c 100644
--- a/drivers/fsi/Kconfig
+++ b/drivers/fsi/Kconfig
@@ -17,6 +17,12 @@ config FSI_MASTER_FAKE
depends on FSI
---help---
This option enables a fake FSI master driver for debugging.
+
+config FSI_MASTER_GPIO
+ tristate "GPIO-based FSI master"
+ depends on FSI
+ ---help---
+ This option enables a FSI master driver using GPIO lines.
endif
endmenu
diff --git a/drivers/fsi/Makefile b/drivers/fsi/Makefile
index 847c00c..2021ce5 100644
--- a/drivers/fsi/Makefile
+++ b/drivers/fsi/Makefile
@@ -1,3 +1,4 @@
obj-$(CONFIG_FSI) += fsi-core.o
obj-$(CONFIG_FSI_MASTER_FAKE) += fsi-master-fake.o
+obj-$(CONFIG_FSI_MASTER_GPIO) += fsi-master-gpio.o
diff --git a/drivers/fsi/fsi-master-gpio.c b/drivers/fsi/fsi-master-gpio.c
new file mode 100644
index 0000000..175281a
--- /dev/null
+++ b/drivers/fsi/fsi-master-gpio.c
@@ -0,0 +1,522 @@
+/*
+ * A FSI master controller, using a simple GPIO bit-banging interface
+ */
+
+#include <linux/platform_device.h>
+#include <linux/gpio/consumer.h>
+#include <linux/module.h>
+#include <linux/delay.h>
+#include <linux/fsi.h>
+
+#include "fsi-master.h"
+
+#define FSI_GPIO_STD_DLY 1 /* Standard pin delay in nS */
+#define FSI_ECHO_DELAY_CLOCKS 16 /* Number clocks for echo delay */
+#define FSI_PRE_BREAK_CLOCKS 50 /* Number clocks to prep for break */
+#define FSI_BREAK_CLOCKS 256 /* Number of clocks to issue break */
+#define FSI_POST_BREAK_CLOCKS 16000 /* Number clocks to set up cfam */
+#define FSI_INIT_CLOCKS 5000 /* Clock out any old data */
+#define FSI_GPIO_STD_DELAY 10 /* Standard GPIO delay in nS */
+ /* todo: adjust down as low as */
+ /* possible or eliminate */
+#define FSI_GPIO_CMD_DPOLL 0x000000000000002AULL
+#define FSI_GPIO_CMD_DPOLL_SIZE 9
+#define FSI_GPIO_DPOLL_CLOCKS 100 /* < 21 will cause slave to hang */
+#define FSI_GPIO_CMD_DEFAULT 0x2000000000000000ULL
+#define FSI_GPIO_CMD_WRITE 0
+#define FSI_GPIO_CMD_READ 0x0400000000000000ULL
+#define FSI_GPIO_CMD_SLAVE_MASK 0xC000000000000000ULL
+#define FSI_GPIO_CMD_ADDR_SHIFT 37
+#define FSI_GPIO_CMD_SLV_SHIFT 62
+#define FSI_GPIO_CMD_SIZE_16 0x0000001000000000ULL
+#define FSI_GPIO_CMD_SIZE_32 0x0000003000000000ULL
+#define FSI_GPIO_CMD_DT32_SHIFT 4
+#define FSI_GPIO_CMD_DT16_SHIFT 20
+#define FSI_GPIO_CMD_DT8_SHIFT 28
+#define FSI_GPIO_CMD_DFLT_LEN 28
+#define FSI_GPIO_CMD_CRC_SHIFT 60
+
+/* Bus errors */
+#define FSI_GPIO_ERR_BUSY 1 /* Slave stuck in busy state */
+#define FSI_GPIO_RESP_ERRA 2 /* Any (misc) Error */
+#define FSI_GPIO_RESP_ERRC 3 /* Slave reports master CRC error */
+#define FSI_GPIO_MTOE 4 /* Master time out error */
+#define FSI_GPIO_CRC_INVAL 5 /* Master reports slave CRC error */
+
+/* Normal slave responses */
+#define FSI_GPIO_RESP_BUSY 1
+#define FSI_GPIO_RESP_ACK 0
+#define FSI_GPIO_RESP_ACKD 4
+
+#define FSI_GPIO_MAX_BUSY 100
+#define FSI_GPIO_MTOE_COUNT 1000
+#define FSI_GPIO_DRAIN_BITS 20
+#define FSI_GPIO_CRC_SIZE 4
+#define FSI_GPIO_MSG_ID_SIZE 2
+#define FSI_GPIO_MSG_RESPID_SIZE 2
+#define FSI_GPIO_PRIME_SLAVE_CLOCKS 100
+
+struct fsi_master_gpio {
+ struct fsi_master master;
+ struct gpio_desc *gpio_clk;
+ struct gpio_desc *gpio_data;
+ struct gpio_desc *gpio_trans; /* Voltage translator */
+ struct gpio_desc *gpio_enable; /* FSI enable */
+ struct gpio_desc *gpio_mux; /* Mux control */
+};
+
+#define to_fsi_master_gpio(m) container_of(m, struct fsi_master_gpio, master)
+
+struct fsi_gpio_msg {
+ uint64_t msg;
+ uint8_t bits;
+};
+
+static void clock_toggle(struct fsi_master_gpio *master, int count)
+{
+ int i;
+
+ for (i = 0; i < count; i++) {
+ ndelay(FSI_GPIO_STD_DLY);
+ gpiod_set_value(master->gpio_clk, 0);
+ ndelay(FSI_GPIO_STD_DLY);
+ gpiod_set_value(master->gpio_clk, 1);
+ }
+}
+
+static int sda_in(struct fsi_master_gpio *master)
+{
+ ndelay(FSI_GPIO_STD_DLY);
+ return gpiod_get_value(master->gpio_data);
+}
+
+static void sda_out(struct fsi_master_gpio *master, int value)
+{
+ gpiod_set_value(master->gpio_data, value);
+}
+
+static void set_sda_input(struct fsi_master_gpio *master)
+{
+ gpiod_direction_input(master->gpio_data);
+ if (master->gpio_trans)
+ gpiod_set_value(master->gpio_trans, 0);
+}
+
+static void set_sda_output(struct fsi_master_gpio *master, int value)
+{
+ gpiod_direction_output(master->gpio_data, value);
+ if (master->gpio_trans)
+ gpiod_set_value(master->gpio_trans, 1);
+}
+
+static void serial_in(struct fsi_master_gpio *master, struct fsi_gpio_msg *cmd,
+ uint8_t num_bits)
+{
+ uint8_t bit;
+ uint64_t msg = 0;
+ uint8_t in_bit = 0;
+
+ set_sda_input(master);
+
+ for (bit = 0; bit < num_bits; bit++) {
+ clock_toggle(master, 1);
+ in_bit = sda_in(master);
+ msg <<= 1;
+ msg |= ~in_bit & 0x1; /* Data is negative active */
+ }
+ cmd->bits = num_bits;
+ cmd->msg = msg;
+}
+
+static void serial_out(struct fsi_master_gpio *master,
+ const struct fsi_gpio_msg *cmd)
+{
+ uint8_t bit;
+ uint64_t msg = ~cmd->msg; /* Data is negative active */
+ uint64_t sda_mask = 0x1ULL << (cmd->bits - 1);
+ uint64_t last_bit = ~0;
+ int next_bit;
+
+ if (!cmd->bits) {
+ dev_warn(master->master.dev, "trying to output 0 bits\n");
+ return;
+ }
+ set_sda_output(master, 0);
+
+ /* Send the start bit */
+ sda_out(master, 0);
+ clock_toggle(master, 1);
+
+ /* Send the message */
+ for (bit = 0; bit < cmd->bits; bit++) {
+ next_bit = (msg & sda_mask) >> (cmd->bits - 1);
+ if (last_bit ^ next_bit) {
+ sda_out(master, next_bit);
+ last_bit = next_bit;
+ }
+ clock_toggle(master, 1);
+ msg <<= 1;
+ }
+}
+
+/*
+ * Clock out some 0's after every message to ride out line reflections
+ */
+static void echo_delay(struct fsi_master_gpio *master)
+{
+ set_sda_output(master, 1);
+ clock_toggle(master, FSI_ECHO_DELAY_CLOCKS);
+}
+
+/*
+ * Used in bus error cases only. Clears out any remaining data the slave
+ * is attempting to send
+ */
+static void drain_response(struct fsi_master_gpio *master)
+{
+ struct fsi_gpio_msg msg;
+
+ serial_in(master, &msg, FSI_GPIO_DRAIN_BITS);
+}
+
+/*
+ * Store information on master errors so handler can detect and clean
+ * up the bus
+ */
+static void fsi_master_gpio_error(struct fsi_master_gpio *master, int error)
+{
+
+}
+
+/*
+ * Taken from Alistaire's PDBG
+ */
+static uint8_t crc4(uint8_t c, int b)
+{
+ uint8_t m = 0;
+
+ c &= 0xf;
+ m = b ^ ((c >> 3) & 0x1);
+ m = (m << 2) | (m << 1) | (m);
+ c <<= 1;
+ c ^= m;
+
+ return c & 0xf;
+}
+
+static int poll_for_response(struct fsi_master_gpio *master, uint8_t expected,
+ uint8_t size, void *data)
+{
+ int busy_count = 0, i;
+ struct fsi_gpio_msg response, cmd;
+ int bits_remaining = 0, bit_count, response_id, id;
+ uint64_t resp = 0;
+ uint8_t bits_received = FSI_GPIO_MSG_ID_SIZE +
+ FSI_GPIO_MSG_RESPID_SIZE;
+ uint8_t crc_in;
+
+ do {
+ for (i = 0; i < FSI_GPIO_MTOE_COUNT; i++) {
+ serial_in(master, &response, 1);
+ if (response.msg)
+ break;
+ }
+ if (i >= FSI_GPIO_MTOE_COUNT) {
+ dev_dbg(master->master.dev,
+ "Master time out waiting for response\n");
+ drain_response(master);
+ fsi_master_gpio_error(master, FSI_GPIO_MTOE);
+ return -EIO;
+ }
+
+ /* Response received */
+ bit_count = FSI_GPIO_MSG_ID_SIZE + FSI_GPIO_MSG_RESPID_SIZE;
+ serial_in(master, &response, bit_count);
+
+ response_id = response.msg & 0x3;
+ id = (response.msg >> FSI_GPIO_MSG_RESPID_SIZE) & 0x3;
+ dev_dbg(master->master.dev, "id:%d resp:%d\n", id, response_id);
+
+ resp = response.msg;
+
+ switch (response_id) {
+ case FSI_GPIO_RESP_ACK:
+ if (expected == FSI_GPIO_RESP_ACKD)
+ bits_remaining = 8 * size;
+ break;
+
+ case FSI_GPIO_RESP_BUSY:
+ /*
+ * Its necessary to clock slave before issuing
+ * d-poll, not indicated in the hardware protocol
+ * spec. < 20 clocks causes slave to hang, 21 ok.
+ */
+ set_sda_output(master, 1);
+ clock_toggle(master, FSI_GPIO_DPOLL_CLOCKS);
+ cmd.msg = FSI_GPIO_CMD_DPOLL;
+ cmd.bits = FSI_GPIO_CMD_DPOLL_SIZE;
+ serial_out(master, &cmd);
+ echo_delay(master);
+ continue;
+
+ case FSI_GPIO_RESP_ERRA:
+ case FSI_GPIO_RESP_ERRC:
+ dev_dbg(master->master.dev, "ERR received: %d\n",
+ (int)response.msg);
+ drain_response(master);
+ fsi_master_gpio_error(master, response.msg);
+ return -EIO;
+ }
+
+ /* Read in the data field if applicable */
+ if (bits_remaining) {
+ serial_in(master, &response, bits_remaining);
+ resp <<= bits_remaining;
+ resp |= response.msg;
+ bits_received += bits_remaining;
+ *((uint32_t *)data) = response.msg;
+ }
+
+ /* Include start bit */
+ crc_in = crc4(0, 1);
+ for (i = bits_received - 1; i >= 0; i--)
+ crc_in = crc4(crc_in, !!(resp & (1ULL << i)));
+
+ /* Read in the crc and check it */
+ serial_in(master, &response, FSI_GPIO_CRC_SIZE);
+ if (crc_in != response.msg) {
+
+ /* CRC's don't match - warn for now */
+ dev_dbg(master->master.dev, "ERR response CRC\n");
+ fsi_master_gpio_error(master, FSI_GPIO_CRC_INVAL);
+ }
+ /* Clock the slave enough to be ready for next operation */
+ clock_toggle(master, FSI_GPIO_PRIME_SLAVE_CLOCKS);
+ return 0;
+
+ } while (busy_count++ < FSI_GPIO_MAX_BUSY);
+
+ dev_dbg(master->master.dev, "ERR slave is stuck in busy state\n");
+ fsi_master_gpio_error(master, FSI_GPIO_ERR_BUSY);
+
+ return -EIO;
+}
+
+static void build_abs_ar_command(struct fsi_gpio_msg *cmd, uint64_t mode,
+ uint8_t slave, uint32_t addr, size_t size,
+ const void *data)
+{
+ uint8_t crc;
+ int i;
+
+ cmd->bits = FSI_GPIO_CMD_DFLT_LEN;
+ cmd->msg = FSI_GPIO_CMD_DEFAULT;
+ cmd->msg |= mode;
+
+ /* todo: handle more than just slave id 0 */
+ cmd->msg &= ~FSI_GPIO_CMD_SLAVE_MASK;
+ cmd->msg |= (((uint64_t)slave) << FSI_GPIO_CMD_SLV_SHIFT);
+ cmd->msg |= (((uint64_t)addr) << FSI_GPIO_CMD_ADDR_SHIFT);
+ if (size == sizeof(uint8_t)) {
+ if (data) {
+ uint8_t cmd_data = *((uint8_t *)data);
+
+ cmd->msg |=
+ ((uint64_t)cmd_data) << FSI_GPIO_CMD_DT8_SHIFT;
+ }
+ } else if (size == sizeof(uint16_t)) {
+ cmd->msg |= FSI_GPIO_CMD_SIZE_16;
+ if (data) {
+ uint16_t cmd_data = *((uint16_t *)data);
+
+ cmd->msg |=
+ ((uint64_t)cmd_data) << FSI_GPIO_CMD_DT16_SHIFT;
+ }
+ } else {
+ cmd->msg |= FSI_GPIO_CMD_SIZE_32;
+ if (data) {
+ uint32_t cmd_data = *((uint32_t *)data);
+
+ cmd->msg |=
+ ((uint64_t)cmd_data) << FSI_GPIO_CMD_DT32_SHIFT;
+ }
+ }
+
+ if (mode == FSI_GPIO_CMD_WRITE)
+ cmd->bits += (8 * size);
+
+ /* Include start bit */
+ crc = crc4(0, 1);
+ for (i = 63; i >= (64 - cmd->bits); i--)
+ crc = crc4(crc, !!(cmd->msg & (1ULL << i)));
+
+ cmd->msg |= ((uint64_t)crc) << (FSI_GPIO_CMD_CRC_SHIFT - cmd->bits);
+ cmd->bits += FSI_GPIO_CRC_SIZE;
+
+ /* Right align message */
+ cmd->msg >>= (64 - cmd->bits);
+}
+
+static int fsi_master_gpio_read(struct fsi_master *_master, int link,
+ uint8_t slave, uint32_t addr, void *val, size_t size)
+{
+ struct fsi_master_gpio *master = to_fsi_master_gpio(_master);
+ struct fsi_gpio_msg cmd;
+
+ if (link != 0)
+ return -ENODEV;
+
+ build_abs_ar_command(&cmd, FSI_GPIO_CMD_READ, slave, addr, size, NULL);
+ serial_out(master, &cmd);
+ echo_delay(master);
+
+ return poll_for_response(master, FSI_GPIO_RESP_ACKD, size, val);
+}
+
+static int fsi_master_gpio_write(struct fsi_master *_master, int link,
+ uint8_t slave, uint32_t addr, const void *val, size_t size)
+{
+ struct fsi_master_gpio *master = to_fsi_master_gpio(_master);
+ struct fsi_gpio_msg cmd;
+
+ if (link != 0)
+ return -ENODEV;
+
+ build_abs_ar_command(&cmd, FSI_GPIO_CMD_WRITE, slave, addr, size, val);
+ serial_out(master, &cmd);
+ echo_delay(master);
+
+ return poll_for_response(master, FSI_GPIO_RESP_ACK, size, NULL);
+}
+
+/*
+ * Issue a break command on link
+ */
+static int fsi_master_gpio_break(struct fsi_master *_master, int link)
+{
+ struct fsi_master_gpio *master = to_fsi_master_gpio(_master);
+
+ if (link != 0)
+ return -ENODEV;
+
+ set_sda_output(master, 1);
+ clock_toggle(master, FSI_PRE_BREAK_CLOCKS);
+ sda_out(master, 0);
+ clock_toggle(master, FSI_BREAK_CLOCKS);
+ echo_delay(master);
+ sda_out(master, 1);
+ clock_toggle(master, FSI_POST_BREAK_CLOCKS);
+
+ /* Wait for logic reset to take effect */
+ udelay(200);
+
+ return 0;
+}
+
+static void fsi_master_gpio_init(struct fsi_master_gpio *master)
+{
+ if (master->gpio_mux)
+ gpiod_direction_output(master->gpio_mux, 1);
+ if (master->gpio_trans)
+ gpiod_direction_output(master->gpio_trans, 1);
+ if (master->gpio_enable)
+ gpiod_direction_output(master->gpio_enable, 0);
+ gpiod_direction_output(master->gpio_clk, 1);
+ gpiod_direction_output(master->gpio_data, 1);
+
+ /* todo: evaluate if clocks can be reduced */
+ clock_toggle(master, FSI_INIT_CLOCKS);
+}
+
+static int fsi_master_gpio_link_enable(struct fsi_master *_master, int link)
+{
+ struct fsi_master_gpio *master = to_fsi_master_gpio(_master);
+
+ if (link != 0)
+ return -ENODEV;
+
+ if (master->gpio_enable)
+ gpiod_set_value(master->gpio_enable, 1);
+
+ return 0;
+}
+
+static int fsi_master_gpio_probe(struct platform_device *pdev)
+{
+ struct fsi_master_gpio *master;
+ struct gpio_desc *gpio;
+
+ master = devm_kzalloc(&pdev->dev, sizeof(*master), GFP_KERNEL);
+ if (!master)
+ return -ENOMEM;
+
+ gpio = devm_gpiod_get(&pdev->dev, "clock", 0);
+ if (IS_ERR(gpio))
+ return PTR_ERR(gpio);
+ master->gpio_clk = gpio;
+
+ gpio = devm_gpiod_get(&pdev->dev, "data", 0);
+ if (IS_ERR(gpio))
+ return PTR_ERR(gpio);
+ master->gpio_data = gpio;
+
+ /* Optional pins */
+
+ gpio = devm_gpiod_get(&pdev->dev, "trans", 0);
+ if (!IS_ERR(gpio))
+ master->gpio_trans = gpio;
+
+ gpio = devm_gpiod_get(&pdev->dev, "enable", 0);
+ if (!IS_ERR(gpio))
+ master->gpio_enable = gpio;
+
+ gpio = devm_gpiod_get(&pdev->dev, "mux", 0);
+ if (!IS_ERR(gpio))
+ master->gpio_mux = gpio;
+
+ master->master.n_links = 1;
+ master->master.read = fsi_master_gpio_read;
+ master->master.write = fsi_master_gpio_write;
+ master->master.send_break = fsi_master_gpio_break;
+ master->master.link_enable = fsi_master_gpio_link_enable;
+
+ fsi_master_gpio_init(master);
+
+ platform_set_drvdata(pdev, master);
+ return fsi_master_register(&master->master);
+}
+
+static int fsi_master_gpio_remove(struct platform_device *pdev)
+{
+ struct fsi_master_gpio *master = platform_get_drvdata(pdev);
+
+ devm_gpiod_put(&pdev->dev, master->gpio_clk);
+ devm_gpiod_put(&pdev->dev, master->gpio_data);
+ if (master->gpio_trans)
+ devm_gpiod_put(&pdev->dev, master->gpio_trans);
+ if (master->gpio_enable)
+ devm_gpiod_put(&pdev->dev, master->gpio_enable);
+ if (master->gpio_mux)
+ devm_gpiod_put(&pdev->dev, master->gpio_mux);
+
+ fsi_master_unregister(&master->master);
+
+ return 0;
+}
+
+static const struct of_device_id fsi_master_gpio_match[] = {
+ { .compatible = "ibm,fsi-master-gpio" },
+ { },
+};
+
+static struct platform_driver fsi_master_gpio_driver = {
+ .driver = {
+ .name = "fsi-master-gpio",
+ .of_match_table = fsi_master_gpio_match,
+ },
+ .probe = fsi_master_gpio_probe,
+ .remove = fsi_master_gpio_remove,
+};
+
+module_platform_driver(fsi_master_gpio_driver);
+MODULE_LICENSE("GPL");
--
1.8.2.2
More information about the openbmc
mailing list