[PATCH] aspeed/g5: Device Tree for ast2500
Maxim Sloyko
maxims at google.com
Sat Oct 15 03:40:44 AEDT 2016
On Thu, Oct 13, 2016 at 5:14 PM, Joel Stanley <joel at jms.id.au> wrote:
> Hi Maxim.
>
> On Fri, Oct 7, 2016 at 4:16 AM, Maxim Sloyko <maxims at google.com> wrote:
> > Ping
>
> I can see your sense of urgency in getting these reviewed. May I
> suggest in the future a few tips for making that happen:
>
> You can make sure you address all of the comments from previous
> reviews. It makes your reviewers feel like you're ignoring them, and
> they're wasting their time, when you're asked to fix something and
> subsequent versions do not have the changes made or a discussion as to
> why you chose not to.
>
This is your reply from Sep 28 to the patch that contained same exact
Device Tree:
---------------- 8 < --------------------- 8 <
------------------------------------
This unrelated to the device tree additions and therefore should be in
a separate patch.
The device tree additions look okay.
--------------- 8 < --------------------- 8 < ------------------------------
--------
This is what I replied on Sep 29:
---------------- 8 < --------------------- 8 <
------------------------------------
> This unrelated to the device tree additions and therefore should be in
> a separate patch.
>
This is related, because the device tree can't be used without this fix.
---------------- 8 < --------------------- 8 <
------------------------------------
However, later same day I sent the same patch without board file
modifications (which is in this thread). Yes, I understand how this might
have created some confusion, but I did not see any replies in either that
thread or this one. So I sent the same patch again, but of course the
device tree on the linux side has changed since the time I originally sent
this, so that's no good anymore -- understandably so, it does not make it
less frustrating.
> Make sure you address the patches to your intended audience. Cedric
> and myself have hacked on our u-boot, and I'm sure you have some peers
> from your project team could help out too. You can put those you want
> to review in the 'to' field when creating the patch.
>
> You can help out by providing review for other patches on the list.
> This helps you understand the best practices and code base, which in
> turn helps you write better patches. It also shows you're here to
> collaborate and assist instead of only caring about your own tasks.
>
> I look forward to working with you as we clean up u-boot and implement
> the features that we require!
>
> Cheers,
>
> Joel
>
> >
> > On Wed, Oct 5, 2016 at 9:16 AM, Maxim Sloyko <maxims at google.com> wrote:
> >>
> >> Ping
> >>
> >> On Thu, Sep 29, 2016 at 11:32 AM, <maxims at google.com> wrote:
> >>>
> >>> From: Maxim Sloyko <maxims at google.com>
> >>>
> >>> Device Tree for ast2500, copied from openbmc/linux (include file), plus
> >>> minimal device tree configuration for ast2500 eval board.
> >>> ---
> >>> arch/arm/dts/Makefile | 2 +
> >>> arch/arm/dts/aspeed-g5-evb.dts | 28 +++
> >>> arch/arm/dts/aspeed-g5.dtsi | 541
> >>> +++++++++++++++++++++++++++++++++++++++++
> >>> 3 files changed, 571 insertions(+)
> >>> create mode 100644 arch/arm/dts/aspeed-g5-evb.dts
> >>> create mode 100644 arch/arm/dts/aspeed-g5.dtsi
> >>>
> >>> diff --git a/arch/arm/dts/Makefile b/arch/arm/dts/Makefile
> >>> index d1f8e22..09efa0a 100644
> >>> --- a/arch/arm/dts/Makefile
> >>> +++ b/arch/arm/dts/Makefile
> >>> @@ -233,6 +233,8 @@ dtb-$(CONFIG_SOC_KEYSTONE) += k2hk-evm.dtb \
> >>> k2e-evm.dtb \
> >>> k2g-evm.dtb
> >>>
> >>> +dtb-$(CONFIG_TARGET_AST_G5) += aspeed-g5-evb.dtb
> >>> +
> >>> targets += $(dtb-y)
> >>>
> >>> # Add any required device tree compiler flags here
> >>> diff --git a/arch/arm/dts/aspeed-g5-evb.dts
> >>> b/arch/arm/dts/aspeed-g5-evb.dts
> >>> new file mode 100644
> >>> index 0000000..95dc77a
> >>> --- /dev/null
> >>> +++ b/arch/arm/dts/aspeed-g5-evb.dts
> >>> @@ -0,0 +1,28 @@
> >>> +/dts-v1/;
> >>> +
> >>> +#include "aspeed-g5.dtsi"
> >>> +
> >>> +/ {
> >>> + memory {
> >>> + device_type = "memory";
> >>> + reg = <0x80000000 0x20000000>;
> >>> + };
> >>> +
> >>> + aliases {
> >>> + i2c1 = &i2c0;
> >>> + i2c4 = &i2c3;
> >>> + i2c8 = &i2c7;
> >>> + };
> >>> +};
> >>> +
> >>> +&i2c0 {
> >>> + status = "okay";
> >>> +};
> >>> +
> >>> +&i2c3 {
> >>> + status = "okay";
> >>> +};
> >>> +
> >>> +&i2c7 {
> >>> + status = "okay";
> >>> +};
> >>> diff --git a/arch/arm/dts/aspeed-g5.dtsi b/arch/arm/dts/aspeed-g5.dtsi
> >>> new file mode 100644
> >>> index 0000000..eb81a2e
> >>> --- /dev/null
> >>> +++ b/arch/arm/dts/aspeed-g5.dtsi
> >>> @@ -0,0 +1,541 @@
> >>> +/* The device tree is copied from
> >>> + *
> >>> https://github.com/openbmc/linux/blob/9ec9d09/arch/arm/boot/
> dts/aspeed-g5.dtsi
> >>> + */
> >>> +#include "skeleton.dtsi"
> >>> +
> >>> +/ {
> >>> + model = "Aspeed BMC";
> >>> + compatible = "aspeed,ast2500";
> >>> + #address-cells = <1>;
> >>> + #size-cells = <1>;
> >>> + interrupt-parent = <&vic>;
> >>> +
> >>> + cpus {
> >>> + #address-cells = <1>;
> >>> + #size-cells = <0>;
> >>> +
> >>> + cpu at 0 {
> >>> + compatible = "arm,arm1176jzf-s";
> >>> + device_type = "cpu";
> >>> + reg = <0>;
> >>> + };
> >>> + };
> >>> +
> >>> + ahb {
> >>> + compatible = "simple-bus";
> >>> + #address-cells = <1>;
> >>> + #size-cells = <1>;
> >>> + ranges;
> >>> +
> >>> + vic: interrupt-controller at 1e6c0080 {
> >>> + compatible = "aspeed,ast2400-vic";
> >>> + interrupt-controller;
> >>> + #interrupt-cells = <1>;
> >>> + valid-sources = <0xfefff7ff 0x0807ffff>;
> >>> + reg = <0x1e6c0080 0x80>;
> >>> + };
> >>> +
> >>> + mac0: ethernet at 1e660000 {
> >>> + compatible = "faraday,ftgmac100";
> >>> + reg = <0x1e660000 0x180>;
> >>> + interrupts = <2>;
> >>> + no-hw-checksum;
> >>> + status = "disabled";
> >>> + };
> >>> +
> >>> + mac1: ethernet at 1e680000 {
> >>> + compatible = "faraday,ftgmac100";
> >>> + reg = <0x1e680000 0x180>;
> >>> + interrupts = <3>;
> >>> + no-hw-checksum;
> >>> + status = "disabled";
> >>> + };
> >>> +
> >>> + apb {
> >>> + compatible = "simple-bus";
> >>> + #address-cells = <1>;
> >>> + #size-cells = <1>;
> >>> + ranges;
> >>> +
> >>> + clk_clkin: clk_clkin at 1e6e2070 {
> >>> + #clock-cells = <0>;
> >>> + compatible = "aspeed,g5-clkin-clock";
> >>> + reg = <0x1e6e2070 0x04>;
> >>> + };
> >>> +
> >>> + syscon: syscon at 1e6e2000 {
> >>> + compatible = "aspeed,g5-scu", "syscon",
> >>> "simple-mfd";
> >>> + reg = <0x1e6e2000 0x1a8>;
> >>> +
> >>> + pinctrl: pinctrl at 1e6e2000 {
> >>> + compatible =
> "aspeed,g5-pinctrl";
> >>> +
> >>> + pinctrl_i2c9_default:
> >>> i2c9_default {
> >>> + function = "I2C9";
> >>> + groups = "I2C9";
> >>> + };
> >>> +
> >>> + pinctrl_i2c10_default:
> >>> i2c10_default {
> >>> + function = "I2C10";
> >>> + groups = "I2C10";
> >>> + };
> >>> +
> >>> + pinctrl_i2c11_default:
> >>> i2c11_default {
> >>> + function = "I2C11";
> >>> + groups = "I2C11";
> >>> + };
> >>> +
> >>> + pinctrl_i2c12_default:
> >>> i2c12_default {
> >>> + function = "I2C12";
> >>> + groups = "I2C12";
> >>> + };
> >>> +
> >>> + pinctrl_i2c13_default:
> >>> i2c13_default {
> >>> + function = "I2C13";
> >>> + groups = "I2C13";
> >>> + };
> >>> +
> >>> + pinctrl_gpid0_default:
> >>> gpid0_default {
> >>> + function = "GPID0";
> >>> + groups = "GPID0";
> >>> + };
> >>> +
> >>> + pinctrl_gpid1_default:
> >>> gpid1_default {
> >>> + function = "GPID1";
> >>> + groups = "GPID1";
> >>> + };
> >>> +
> >>> + pinctrl_sd1_default:
> sd1_default
> >>> {
> >>> + function = "SD1";
> >>> + groups = "SD1";
> >>> + };
> >>> +
> >>> + pinctrl_i2c5_default:
> >>> i2c5_default {
> >>> + function = "I2C5";
> >>> + groups = "I2C5";
> >>> + };
> >>> +
> >>> + pinctrl_i2c6_default:
> >>> i2c6_default {
> >>> + function = "I2C6";
> >>> + groups = "I2C6";
> >>> + };
> >>> +
> >>> + pinctrl_i2c7_default:
> >>> i2c7_default {
> >>> + function = "I2C7";
> >>> + groups = "I2C7";
> >>> + };
> >>> +
> >>> + pinctrl_i2c8_default:
> >>> i2c8_default {
> >>> + function = "I2C8";
> >>> + groups = "I2C8";
> >>> + };
> >>> +
> >>> + pinctrl_pwm0_default:
> >>> pwm0_default {
> >>> + function = "PWM0";
> >>> + groups = "PWM0";
> >>> + };
> >>> +
> >>> + pinctrl_pwm1_default:
> >>> pwm1_default {
> >>> + function = "PWM1";
> >>> + groups = "PWM1";
> >>> + };
> >>> +
> >>> + pinctrl_pwm2_default:
> >>> pwm2_default {
> >>> + function = "PWM2";
> >>> + groups = "PWM2";
> >>> + };
> >>> +
> >>> + pinctrl_pwm3_default:
> >>> pwm3_default {
> >>> + function = "PWM3";
> >>> + groups = "PWM3";
> >>> + };
> >>> +
> >>> + pinctrl_pwm4_default:
> >>> pwm4_default {
> >>> + function = "PWM4";
> >>> + groups = "PWM4";
> >>> + };
> >>> +
> >>> + pinctrl_pwm5_default:
> >>> pwm5_default {
> >>> + function = "PWM5";
> >>> + groups = "PWM5";
> >>> + };
> >>> +
> >>> + pinctrl_pwm6_default:
> >>> pwm6_default {
> >>> + function = "PWM6";
> >>> + groups = "PWM6";
> >>> + };
> >>> +
> >>> + pinctrl_pwm7_default:
> >>> pwm7_default {
> >>> + function = "PWM7";
> >>> + groups = "PWM7";
> >>> + };
> >>> +
> >>> + pinctrl_i2c3_default:
> >>> i2c3_default {
> >>> + function = "I2C3";
> >>> + groups = "I2C3";
> >>> + };
> >>> +
> >>> + pinctrl_i2c4_default:
> >>> i2c4_default {
> >>> + function = "I2C4";
> >>> + groups = "I2C4";
> >>> + };
> >>> +
> >>> + pinctrl_i2c14_default:
> >>> i2c14_default {
> >>> + function = "I2C14";
> >>> + groups = "I2C14";
> >>> + };
> >>> +
> >>> + pinctrl_rgmii1_default:
> >>> rgmii1_default {
> >>> + function = "RGMII1";
> >>> + groups = "RGMII1";
> >>> + };
> >>> +
> >>> + pinctrl_rmii1_default:
> >>> rmii1_default {
> >>> + function = "RMII1";
> >>> + groups = "RMII1";
> >>> + };
> >>> +
> >>> + pinctrl_rgmii2_default:
> >>> rgmii2_default {
> >>> + function = "RGMII2";
> >>> + groups = "RGMII2";
> >>> + };
> >>> +
> >>> + pinctrl_rmii2_default:
> >>> rmii2_default {
> >>> + function = "RMII2";
> >>> + groups = "RMII2";
> >>> + };
> >>> + };
> >>> + };
> >>> +
> >>> + clk_hpll: clk_hpll at 1e6e2024 {
> >>> + #clock-cells = <0>;
> >>> + compatible = "aspeed,g5-hpll-clock";
> >>> + reg = <0x1e6e2024 0x4>;
> >>> + clocks = <&clk_clkin>;
> >>> + };
> >>> +
> >>> + clk_ahb: clk_ahb at 1e6e2070 {
> >>> + #clock-cells = <0>;
> >>> + compatible = "aspeed,g5-ahb-clock";
> >>> + reg = <0x1e6e2070 0x4>;
> >>> + clocks = <&clk_hpll>;
> >>> + };
> >>> +
> >>> + clk_apb: clk_apb at 1e6e2008 {
> >>> + #clock-cells = <0>;
> >>> + compatible = "aspeed,g5-apb-clock";
> >>> + reg = <0x1e6e2008 0x4>;
> >>> + clocks = <&clk_hpll>;
> >>> + };
> >>> +
> >>> + clk_uart: clk_uart at 1e6e2008 {
> >>> + #clock-cells = <0>;
> >>> + compatible = "aspeed,uart-clock";
> >>> + reg = <0x1e6e202c 0x4>;
> >>> + };
> >>> +
> >>> + sram at 1e720000 {
> >>> + compatible = "mmio-sram";
> >>> + reg = <0x1e720000 0x9000>; // 36K
> >>> + };
> >>> +
> >>> + gpio: gpio at 1e780000 {
> >>> + #gpio-cells = <2>;
> >>> + gpio-controller;
> >>> + compatible = "aspeed,ast2500-gpio";
> >>> + reg = <0x1e780000 0x1000>;
> >>> + interrupts = <20>;
> >>> + gpio-ranges = <&pinctrl 0 0 220>;
> >>> + };
> >>> +
> >>> + timer: timer at 1e782000 {
> >>> + compatible = "aspeed,ast2400-timer";
> >>> + reg = <0x1e782000 0x90>;
> >>> + // The moxart_timer driver registers
> only
> >>> one
> >>> + // interrupt and assumes it's for
> timer 1
> >>> + //interrupts = <16 17 18 35 36 37 38
> 39>;
> >>> + interrupts = <16>;
> >>> + clocks = <&clk_apb>;
> >>> + };
> >>> +
> >>> + ibt: ibt at 1e789140 {
> >>> + compatible = "aspeed,bt-host";
> >>> + reg = <0x1e789140 0x18>;
> >>> + interrupts = <8>;
> >>> + };
> >>> +
> >>> + wdt1: wdt at 1e785000 {
> >>> + compatible = "aspeed,ast2500-wdt";
> >>> + reg = <0x1e785000 0x1c>;
> >>> + };
> >>> +
> >>> + wdt2: wdt at 1e785020 {
> >>> + compatible = "aspeed,ast2500-wdt";
> >>> + reg = <0x1e785020 0x1c>;
> >>> + status = "disabled";
> >>> + };
> >>> +
> >>> + wdt3: wdt at 1e785040 {
> >>> + compatible = "aspeed,wdt";
> >>> + reg = <0x1e785074 0x1c>;
> >>> + status = "disabled";
> >>> + };
> >>> +
> >>> + uart1: serial at 1e783000 {
> >>> + compatible = "ns16550a";
> >>> + reg = <0x1e783000 0x1000>;
> >>> + reg-shift = <2>;
> >>> + interrupts = <9>;
> >>> + clocks = <&clk_uart>;
> >>> + no-loopback-test;
> >>> + status = "disabled";
> >>> + };
> >>> +
> >>> + uart2: serial at 1e78d000 {
> >>> + compatible = "ns16550a";
> >>> + reg = <0x1e78d000 0x1000>;
> >>> + reg-shift = <2>;
> >>> + interrupts = <32>;
> >>> + clocks = <&clk_uart>;
> >>> + no-loopback-test;
> >>> + status = "disabled";
> >>> + };
> >>> +
> >>> + uart3: serial at 1e78e000 {
> >>> + compatible = "ns16550a";
> >>> + reg = <0x1e78e000 0x1000>;
> >>> + reg-shift = <2>;
> >>> + interrupts = <33>;
> >>> + clocks = <&clk_uart>;
> >>> + no-loopback-test;
> >>> + status = "disabled";
> >>> + };
> >>> +
> >>> + uart4: serial at 1e78f000 {
> >>> + compatible = "ns16550a";
> >>> + reg = <0x1e78f000 0x1000>;
> >>> + reg-shift = <2>;
> >>> + interrupts = <34>;
> >>> + clocks = <&clk_uart>;
> >>> + no-loopback-test;
> >>> + status = "disabled";
> >>> + };
> >>> +
> >>> + uart5: serial at 1e784000 {
> >>> + compatible = "ns16550a";
> >>> + reg = <0x1e784000 0x1000>;
> >>> + reg-shift = <2>;
> >>> + interrupts = <10>;
> >>> + clocks = <&clk_uart>;
> >>> + current-speed = <38400>;
> >>> + no-loopback-test;
> >>> + status = "disabled";
> >>> + };
> >>> +
> >>> + vuart: vuart at 1e787000 {
> >>> + compatible = "aspeed,vuart";
> >>> + reg = <0x1e787000 0x1000>;
> >>> + reg-shift = <2>;
> >>> + interrupts = <8>;
> >>> + clocks = <&clk_uart>;
> >>> + no-loopback-test;
> >>> + status = "disabled";
> >>> + };
> >>> +
> >>> + i2c: i2c at 1e78a000 {
> >>> + #address-cells = <1>;
> >>> + #size-cells = <1>;
> >>> + #interrupt-cells = <1>;
> >>> +
> >>> + compatible =
> >>> "aspeed,ast2400-i2c-controller";
> >>> + reg = <0x1e78a000 0x40>;
> >>> + ranges = <0 0x1e78a000 0x1000>;
> >>> + interrupts = <12>;
> >>> + clocks = <&clk_apb>;
> >>> + clock-ranges;
> >>> + interrupt-controller;
> >>> +
> >>> + i2c0: i2c-bus at 40 {
> >>> + #address-cells = <1>;
> >>> + #size-cells = <0>;
> >>> + reg = <0x40 0x40>;
> >>> + compatible =
> >>> "aspeed,ast2400-i2c-bus";
> >>> + bus = <0>;
> >>> + clock-frequency = <100000>;
> >>> + status = "disabled";
> >>> + interrupts = <0>;
> >>> + interrupt-parent = <&i2c>;
> >>> + };
> >>> +
> >>> + i2c1: i2c-bus at 80 {
> >>> + #address-cells = <1>;
> >>> + #size-cells = <0>;
> >>> + reg = <0x80 0x40>;
> >>> + compatible =
> >>> "aspeed,ast2400-i2c-bus";
> >>> + bus = <1>;
> >>> + clock-frequency = <100000>;
> >>> + status = "disabled";
> >>> + interrupts = <1>;
> >>> + };
> >>> +
> >>> + i2c2: i2c-bus at c0 {
> >>> + #address-cells = <1>;
> >>> + #size-cells = <0>;
> >>> + reg = <0xC0 0x40>;
> >>> + compatible =
> >>> "aspeed,ast2400-i2c-bus";
> >>> + bus = <2>;
> >>> + clock-frequency = <100000>;
> >>> + status = "disabled";
> >>> + interrupts = <2>;
> >>> + pinctrl-names = "default";
> >>> + pinctrl-0 =
> >>> <&pinctrl_i2c3_default>;
> >>> + };
> >>> +
> >>> + i2c3: i2c-bus at 100 {
> >>> + #address-cells = <1>;
> >>> + #size-cells = <0>;
> >>> + reg = <0x100 0x40>;
> >>> + compatible =
> >>> "aspeed,ast2400-i2c-bus";
> >>> + bus = <3>;
> >>> + clock-frequency = <100000>;
> >>> + status = "disabled";
> >>> + interrupts = <3>;
> >>> + pinctrl-names = "default";
> >>> + pinctrl-0 =
> >>> <&pinctrl_i2c4_default>;
> >>> + };
> >>> +
> >>> + i2c4: i2c-bus at 140 {
> >>> + #address-cells = <1>;
> >>> + #size-cells = <0>;
> >>> + reg = <0x140 0x40>;
> >>> + compatible =
> >>> "aspeed,ast2400-i2c-bus";
> >>> + bus = <4>;
> >>> + clock-frequency = <100000>;
> >>> + status = "disabled";
> >>> + interrupts = <4>;
> >>> + pinctrl-names = "default";
> >>> + pinctrl-0 =
> >>> <&pinctrl_i2c5_default>;
> >>> + };
> >>> +
> >>> + i2c5: i2c-bus at 180 {
> >>> + #address-cells = <1>;
> >>> + #size-cells = <0>;
> >>> + reg = <0x180 0x40>;
> >>> + compatible =
> >>> "aspeed,ast2400-i2c-bus";
> >>> + bus = <5>;
> >>> + clock-frequency = <100000>;
> >>> + status = "disabled";
> >>> + interrupts = <5>;
> >>> + pinctrl-names = "default";
> >>> + pinctrl-0 =
> >>> <&pinctrl_i2c6_default>;
> >>> + };
> >>> +
> >>> + i2c6: i2c-bus at 1c0 {
> >>> + #address-cells = <1>;
> >>> + #size-cells = <0>;
> >>> + reg = <0x1C0 0x40>;
> >>> + compatible =
> >>> "aspeed,ast2400-i2c-bus";
> >>> + bus = <6>;
> >>> + clock-frequency = <100000>;
> >>> + status = "disabled";
> >>> + interrupts = <6>;
> >>> + pinctrl-names = "default";
> >>> + pinctrl-0 =
> >>> <&pinctrl_i2c7_default>;
> >>> + };
> >>> +
> >>> + i2c7: i2c-bus at 300 {
> >>> + #address-cells = <1>;
> >>> + #size-cells = <0>;
> >>> + reg = <0x300 0x40>;
> >>> + compatible =
> >>> "aspeed,ast2400-i2c-bus";
> >>> + bus = <7>;
> >>> + clock-frequency = <100000>;
> >>> + status = "disabled";
> >>> + interrupts = <7>;
> >>> + pinctrl-names = "default";
> >>> + pinctrl-0 =
> >>> <&pinctrl_i2c8_default>;
> >>> + };
> >>> +
> >>> + i2c8: i2c-bus at 340 {
> >>> + #address-cells = <1>;
> >>> + #size-cells = <0>;
> >>> + reg = <0x340 0x40>;
> >>> + compatible =
> >>> "aspeed,ast2400-i2c-bus";
> >>> + bus = <8>;
> >>> + clock-frequency = <100000>;
> >>> + status = "disabled";
> >>> + interrupts = <8>;
> >>> + pinctrl-names = "default";
> >>> + pinctrl-0 =
> >>> <&pinctrl_i2c9_default>;
> >>> + };
> >>> +
> >>> + i2c9: i2c-bus at 380 {
> >>> + #address-cells = <1>;
> >>> + #size-cells = <0>;
> >>> + reg = <0x380 0x40>;
> >>> + compatible =
> >>> "aspeed,ast2400-i2c-bus";
> >>> + bus = <9>;
> >>> + clock-frequency = <100000>;
> >>> + status = "disabled";
> >>> + interrupts = <9>;
> >>> + pinctrl-names = "default";
> >>> + pinctrl-0 =
> >>> <&pinctrl_i2c10_default>;
> >>> + };
> >>> +
> >>> + i2c10: i2c-bus at 3c0 {
> >>> + #address-cells = <1>;
> >>> + #size-cells = <0>;
> >>> + reg = <0x3c0 0x40>;
> >>> + compatible =
> >>> "aspeed,ast2400-i2c-bus";
> >>> + bus = <10>;
> >>> + clock-frequency = <100000>;
> >>> + status = "disabled";
> >>> + interrupts = <10>;
> >>> + pinctrl-names = "default";
> >>> + pinctrl-0 =
> >>> <&pinctrl_i2c11_default>;
> >>> + };
> >>> +
> >>> + i2c11: i2c-bus at 400 {
> >>> + #address-cells = <1>;
> >>> + #size-cells = <0>;
> >>> + reg = <0x400 0x40>;
> >>> + compatible =
> >>> "aspeed,ast2400-i2c-bus";
> >>> + bus = <11>;
> >>> + clock-frequency = <100000>;
> >>> + status = "disabled";
> >>> + interrupts = <11>;
> >>> + pinctrl-names = "default";
> >>> + pinctrl-0 =
> >>> <&pinctrl_i2c12_default>;
> >>> + };
> >>> +
> >>> + i2c12: i2c-bus at 440 {
> >>> + #address-cells = <1>;
> >>> + #size-cells = <0>;
> >>> + reg = <0x440 0x40>;
> >>> + compatible =
> >>> "aspeed,ast2400-i2c-bus";
> >>> + bus = <12>;
> >>> + clock-frequency = <100000>;
> >>> + status = "disabled";
> >>> + interrupts = <12>;
> >>> + pinctrl-names = "default";
> >>> + pinctrl-0 =
> >>> <&pinctrl_i2c13_default>;
> >>> + };
> >>> +
> >>> + i2c13: i2c-bus at 480 {
> >>> + #address-cells = <1>;
> >>> + #size-cells = <0>;
> >>> + reg = <0x480 0x40>;
> >>> + compatible =
> >>> "aspeed,ast2400-i2c-bus";
> >>> + bus = <13>;
> >>> + clock-frequency = <100000>;
> >>> + status = "disabled";
> >>> + interrupts = <13>;
> >>> + pinctrl-names = "default";
> >>> + pinctrl-0 =
> >>> <&pinctrl_i2c14_default>;
> >>> + };
> >>> +
> >>> + };
> >>> +
> >>> + };
> >>> + };
> >>> +};
> >>> --
> >>> 2.8.0.rc3.226.g39d4020
> >>>
> >>
> >>
> >>
> >> --
> >> Maxim Sloyko
> >
> >
> >
> >
> > --
> > Maxim Sloyko
> >
> > _______________________________________________
> > openbmc mailing list
> > openbmc at lists.ozlabs.org
> > https://lists.ozlabs.org/listinfo/openbmc
> >
>
--
*M*axim *S*loyko
-------------- next part --------------
An HTML attachment was scrubbed...
URL: <http://lists.ozlabs.org/pipermail/openbmc/attachments/20161014/d9171fb4/attachment-0001.html>
More information about the openbmc
mailing list