[PATCH] ppc64: iMac G5 cpufreq support
Benjamin Herrenschmidt
benh at kernel.crashing.org
Wed Sep 21 15:57:28 EST 2005
This applies on top of the big SMU update posted earlier. It adds
cpufreq support for iMac G5 (and SMU based desktop, though that one was
untested, testers welcome). It supports full and half speed and also
does voltage switching for more power savings.
Next step is proper thermal control to make those fans quiet once for
all !
Index: linux-work/arch/ppc64/kernel/misc.S
===================================================================
--- linux-work.orig/arch/ppc64/kernel/misc.S 2005-09-20 14:57:41.000000000 +1000
+++ linux-work/arch/ppc64/kernel/misc.S 2005-09-21 13:39:11.000000000 +1000
@@ -616,7 +616,7 @@
isync
blr
- /*
+/*
* Do an IO access in real mode
*/
_GLOBAL(real_writeb)
@@ -649,6 +649,73 @@
#endif /* defined(CONFIG_PPC_PMAC) || defined(CONFIG_PPC_MAPLE) */
/*
+ * SCOM access functions for 970 (FX only for now)
+ *
+ * unsigned long scom970_read(unsigned int address);
+ * void scom970_write(unsigned int address, unsigned long value);
+ *
+ * The address passed in is the 24 bits register address. This code
+ * is 970 specific and will not check the status bits, so you should
+ * know what you are doing.
+ */
+_GLOBAL(scom970_read)
+ /* interrupts off */
+ mfmsr r4
+ li r0,0
+ rlwimi r0,r4,0,MSR_EE
+ mtmsrd r0,1
+
+ /* rotate address 8 bits left, mask out low 16 bits as they
+ * aren't implemented on current CPUs and must be 0'd,
+ * and finally or in RW bit
+ */
+ rlwinm r3,r3,8,0,15
+ ori r3,r3,0x8000
+
+ /* do the actual scom read */
+ sync
+ mtspr SPRN_SCOMC,r3
+ isync
+ mfspr r3,SPRN_SCOMD
+ mfspr r0,SPRN_SCOMC
+ sync
+ isync
+
+ /* XXX: fixup result on some buggy 970's (ouch ! we lost a bit, bah
+ * that's the best we can do). Not implemented yet as we don't use
+ * the scom on any of the bogus CPUs yet, but may have to be done
+ * ultimately
+ */
+
+ /* restore interrupts */
+ mtmsrd r4,1
+ blr
+
+
+_GLOBAL(scom970_write)
+ /* interrupts off */
+ mfmsr r5
+ li r0,0
+ rlwimi r0,r5,0,MSR_EE
+ mtmsrd r0,1
+
+ /* rotate address 8 bits left, mask out low 16 bits as they
+ * aren't implemented on current CPUs and must be 0'd
+ */
+ rlwinm r3,r3,8,0,15
+
+ mtspr SPRN_SCOMD,r4 /* write data */
+ mtspr SPRN_SCOMC,r3 /* write command */
+ sync
+ isync
+ mfspr 3,SPRN_SCOMC
+
+ /* restore interrupts */
+ mtmsrd r5,1
+ blr
+
+
+/*
* Create a kernel thread
* kernel_thread(fn, arg, flags)
*/
Index: linux-work/include/asm-ppc64/processor.h
===================================================================
--- linux-work.orig/include/asm-ppc64/processor.h 2005-09-20 09:54:26.000000000 +1000
+++ linux-work/include/asm-ppc64/processor.h 2005-09-20 16:00:42.000000000 +1000
@@ -177,6 +177,9 @@
#define SPRN_CTRLT 0x098
#define CTRL_RUNLATCH 0x1
+#define SPRN_SCOMC 0x114
+#define SPRN_SCOMD 0x115
+
/* Performance monitor SPRs */
#define SPRN_SIAR 780
#define SPRN_SDAR 781
@@ -536,6 +539,9 @@
}
}
+extern unsigned long scom970_read(unsigned int address);
+extern void scom970_write(unsigned int address, unsigned long value);
+
#endif /* __KERNEL__ */
#endif /* __ASSEMBLY__ */
Index: linux-work/arch/ppc64/Kconfig
===================================================================
--- linux-work.orig/arch/ppc64/Kconfig 2005-09-20 14:57:39.000000000 +1000
+++ linux-work/arch/ppc64/Kconfig 2005-09-20 16:04:28.000000000 +1000
@@ -159,6 +159,17 @@
support. As of this writing the exact hardware interface is
strongly in flux, so no good recommendation can be made.
+source "drivers/cpufreq/Kconfig"
+
+config CPU_FREQ_PMAC
+ bool "Support for Apple G5"
+ depends on CPU_FREQ && PPC_PMAC64
+ select CPU_FREQ_TABLE
+ help
+ This adds support for frequency switching on some Apple G5
+ machine. This is currently very experimental and works only
+ on some iMac G5.
+
config IBMVIO
depends on PPC_PSERIES || PPC_ISERIES
bool
Index: linux-work/arch/ppc64/kernel/Makefile
===================================================================
--- linux-work.orig/arch/ppc64/kernel/Makefile 2005-09-07 11:09:56.000000000 +1000
+++ linux-work/arch/ppc64/kernel/Makefile 2005-09-20 16:05:32.000000000 +1000
@@ -60,6 +60,7 @@
obj-$(CONFIG_PPC_PMAC) += pmac_setup.o pmac_feature.o pmac_pci.o \
pmac_time.o pmac_nvram.o pmac_low_i2c.o \
udbg_scc.o
+obj-$(CONFIG_CPU_FREQ_PMAC) += pmac_cpufreq.o
obj-$(CONFIG_PPC_MAPLE) += maple_setup.o maple_pci.o maple_time.o \
udbg_16550.o
Index: linux-work/arch/ppc64/kernel/pmac_cpufreq.c
===================================================================
--- /dev/null 1970-01-01 00:00:00.000000000 +0000
+++ linux-work/arch/ppc64/kernel/pmac_cpufreq.c 2005-09-21 15:58:08.000000000 +1000
@@ -0,0 +1,297 @@
+/*
+ * Copyright (C) 2002 - 2005 Benjamin Herrenschmidt <benh at kernel.crashing.org>
+ * and Markus Demleitner <msdemlei at cl.uni-heidelberg.de>
+ *
+ * This program is free software; you can redistribute it and/or modify
+ * it under the terms of the GNU General Public License version 2 as
+ * published by the Free Software Foundation.
+ *
+ * This driver adds basic cpufreq support for SMU & 970FX based G5 Macs,
+ * that is iMac G5 and latest single CPU desktop.
+ */
+
+#include <linux/config.h>
+#include <linux/module.h>
+#include <linux/types.h>
+#include <linux/errno.h>
+#include <linux/kernel.h>
+#include <linux/delay.h>
+#include <linux/sched.h>
+#include <linux/slab.h>
+#include <linux/cpufreq.h>
+#include <linux/init.h>
+#include <linux/completion.h>
+#include <asm/prom.h>
+#include <asm/machdep.h>
+#include <asm/irq.h>
+#include <asm/sections.h>
+#include <asm/cputable.h>
+#include <asm/time.h>
+#include <asm/smu.h>
+
+#undef DEBUG
+
+#ifdef DEBUG
+#define DBG(fmt...) printk(fmt)
+#else
+#define DBG(fmt...)
+#endif
+
+/* see 970FX user manual */
+
+#define SCOM_PCR 0x0aa001 /* PCR scom addr */
+
+#define PCR_HILO_SELECT 0x80000000U /* 1 = PCR, 0 = PCRH */
+#define PCR_SPEED_FULL 0x00000000U /* 1:1 speed value */
+#define PCR_SPEED_HALF 0x00020000U /* 1:2 speed value */
+#define PCR_SPEED_QUARTER 0x00040000U /* 1:4 speed value */
+#define PCR_SPEED_MASK 0x000e0000U /* speed mask */
+#define PCR_SPEED_SHIFT 17
+#define PCR_FREQ_REQ_VALID 0x00010000U /* freq request valid */
+#define PCR_VOLT_REQ_VALID 0x00008000U /* volt request valid */
+#define PCR_TARGET_TIME_MASK 0x00006000U /* target time */
+#define PCR_STATLAT_MASK 0x00001f00U /* STATLAT value */
+#define PCR_SNOOPLAT_MASK 0x000000f0U /* SNOOPLAT value */
+#define PCR_SNOOPACC_MASK 0x0000000fU /* SNOOPACC value */
+
+#define SCOM_PSR 0x408001 /* PSR scom addr */
+/* warning: PSR is a 64 bits register */
+#define PSR_CMD_RECEIVED 0x2000000000000000U /* command received */
+#define PSR_CMD_COMPLETED 0x1000000000000000U /* command completed */
+#define PSR_CUR_SPEED_MASK 0x0300000000000000U /* current speed */
+#define PSR_CUR_SPEED_SHIFT (56)
+
+/*
+ * The G5 only supports two frequencies (Quarter speed is not supported)
+ */
+#define CPUFREQ_HIGH 0
+#define CPUFREQ_LOW 1
+
+static struct cpufreq_frequency_table g5_cpu_freqs[] = {
+ {CPUFREQ_HIGH, 0},
+ {CPUFREQ_LOW, 0},
+ {0, CPUFREQ_TABLE_END},
+};
+
+static struct freq_attr* g5_cpu_freqs_attr[] = {
+ &cpufreq_freq_attr_scaling_available_freqs,
+ NULL,
+};
+
+/* Power mode data is an array of the 32 bits PCR values to use for
+ * the various frequencies, retreived from the device-tree
+ */
+static u32 *g5_pmode_data;
+static int g5_pmode_max;
+static int g5_pmode_cur;
+
+
+static struct smu_sdbp_fvt *g5_fvt_table; /* table of op. points */
+static int g5_fvt_count; /* number of op. points */
+static int g5_fvt_cur; /* current op. point */
+
+/* ----------------- real hardware interface */
+
+static void g5_switch_volt(int speed_mode)
+{
+ struct smu_simple_cmd cmd;
+
+ DECLARE_COMPLETION(comp);
+ smu_queue_simple(&cmd, SMU_CMD_POWER_COMMAND, 8, smu_done_complete,
+ &comp, 'V', 'S', 'L', 'E', 'W',
+ 0xff, g5_fvt_cur+1, speed_mode);
+ wait_for_completion(&comp);
+}
+
+static int g5_switch_freq(int speed_mode)
+{
+ int to;
+
+ if (g5_pmode_cur == speed_mode)
+ return 0;
+
+ /* If frequency is going up, first ramp up the voltage */
+ if (speed_mode < g5_pmode_cur)
+ g5_switch_volt(speed_mode);
+
+ /* Clear PCR high */
+ scom970_write(SCOM_PCR, 0);
+ /* Clear PCR low */
+ scom970_write(SCOM_PCR, PCR_HILO_SELECT | 0);
+ /* Set PCR low */
+ scom970_write(SCOM_PCR, PCR_HILO_SELECT |
+ g5_pmode_data[speed_mode]);
+
+ /* Wait for completion */
+ for (to = 0; to < 10; to++) {
+ unsigned long psr = scom970_read(SCOM_PSR);
+
+ if ((psr & PSR_CMD_RECEIVED) == 0 &&
+ (((psr >> PSR_CUR_SPEED_SHIFT) ^
+ (g5_pmode_data[speed_mode] >> PCR_SPEED_SHIFT)) & 0x3)
+ == 0)
+ break;
+ if (psr & PSR_CMD_COMPLETED)
+ break;
+ udelay(100);
+ }
+
+ /* If frequency is going down, last ramp the voltage */
+ if (speed_mode > g5_pmode_cur)
+ g5_switch_volt(speed_mode);
+
+ g5_pmode_cur = speed_mode;
+ ppc_proc_freq = g5_cpu_freqs[speed_mode].frequency;
+
+ return 0;
+}
+
+static int g5_query_freq(void)
+{
+ unsigned long psr = scom970_read(SCOM_PSR);
+ int i;
+
+ for (i = 0; i <= g5_pmode_max; i++)
+ if ((((psr >> PSR_CUR_SPEED_SHIFT) ^
+ (g5_pmode_data[i] >> PCR_SPEED_SHIFT)) & 0x3) == 0)
+ break;
+ return i;
+}
+
+/* ----------------- cpufreq bookkeeping */
+static int __pmac g5_cpufreq_verify(struct cpufreq_policy *policy)
+{
+ return cpufreq_frequency_table_verify(policy, g5_cpu_freqs);
+}
+
+static int __pmac g5_cpufreq_target(struct cpufreq_policy *policy,
+ unsigned int target_freq, unsigned int relation)
+{
+ unsigned int newstate = 0;
+
+ if (cpufreq_frequency_table_target(policy, g5_cpu_freqs,
+ target_freq, relation, &newstate))
+ return -EINVAL;
+
+ return g5_switch_freq(newstate);
+}
+
+static int __pmac g5_cpufreq_cpu_init(struct cpufreq_policy *policy)
+{
+ if (policy->cpu != 0)
+ return -ENODEV;
+
+ policy->governor = CPUFREQ_DEFAULT_GOVERNOR;
+ policy->cpuinfo.transition_latency = CPUFREQ_ETERNAL;
+ policy->cur = g5_cpu_freqs[g5_query_freq()].frequency;
+ cpufreq_frequency_table_get_attr(g5_cpu_freqs, policy->cpu);
+
+ return cpufreq_frequency_table_cpuinfo(policy,
+ g5_cpu_freqs);
+}
+
+
+static struct cpufreq_driver g5_cpufreq_driver = {
+ .name = "powermac",
+ .owner = THIS_MODULE,
+ .flags = CPUFREQ_CONST_LOOPS,
+ .init = g5_cpufreq_cpu_init,
+ .verify = g5_cpufreq_verify,
+ .target = g5_cpufreq_target,
+ .attr = g5_cpu_freqs_attr,
+};
+
+
+static int __init g5_cpufreq_init(void)
+{
+ struct device_node *cpunode;
+ unsigned int psize, ssize;
+ struct smu_sdbp_header *shdr;
+ unsigned long max_freq;
+ u32 *valp;
+ int rc = -ENODEV;
+
+ /* Look for CPU and SMU nodes */
+ cpunode = of_find_node_by_type(NULL, "cpu");
+ if (!cpunode) {
+ DBG("No CPU node !\n");
+ return -ENODEV;
+ }
+
+ /* Check 970FX for now */
+ valp = (u32 *)get_property(cpunode, "cpu-version", NULL);
+ if (!valp) {
+ DBG("No cpu-version property !\n");
+ goto bail_noprops;
+ }
+ if (((*valp) >> 16) != 0x3c) {
+ DBG("Wrong CPU version: %08x\n", *valp);
+ goto bail_noprops;
+ }
+
+ /* Look for the powertune data in the device-tree */
+ g5_pmode_data = (u32 *)get_property(cpunode, "power-mode-data",&psize);
+ if (!g5_pmode_data) {
+ DBG("No power-mode-data !\n");
+ goto bail_noprops;
+ }
+ g5_pmode_max = psize / sizeof(u32) - 1;
+
+ /* Look for the FVT table */
+ shdr = smu_get_sdb_partition(SMU_SDB_FVT_ID, NULL);
+ if (!shdr)
+ goto bail_noprops;
+ g5_fvt_table = (struct smu_sdbp_fvt *)&shdr[1];
+ ssize = (shdr->len * sizeof(u32)) - sizeof(struct smu_sdbp_header);
+ g5_fvt_count = ssize / sizeof(struct smu_sdbp_fvt);
+ g5_fvt_cur = 0;
+
+ /* Sanity checking */
+ if (g5_fvt_count < 1 || g5_pmode_max < 1)
+ goto bail_noprops;
+
+ /*
+ * From what I see, clock-frequency is always the maximal frequency.
+ * The current driver can not slew sysclk yet, so we really only deal
+ * with powertune steps for now. We also only implement full freq and
+ * half freq in this version. So far, I haven't yet seen a machine
+ * supporting anything else.
+ */
+ valp = (u32 *)get_property(cpunode, "clock-frequency", NULL);
+ if (!valp)
+ return -ENODEV;
+ max_freq = (*valp)/1000;
+ g5_cpu_freqs[0].frequency = max_freq;
+ g5_cpu_freqs[1].frequency = max_freq/2;
+
+ /* Check current frequency */
+ g5_pmode_cur = g5_query_freq();
+ if (g5_pmode_cur > 1) {
+ /* We don't support anything but 1:1 and 1:2, fixup ... */
+ g5_switch_freq(1);
+ g5_pmode_cur = 1;
+ }
+
+ printk(KERN_INFO "Registering G5 CPU frequency driver\n");
+ printk(KERN_INFO "Low: %d Mhz, High: %d Mhz, Cur: %d MHz\n",
+ g5_cpu_freqs[1].frequency/1000,
+ g5_cpu_freqs[0].frequency/1000,
+ g5_cpu_freqs[g5_pmode_cur].frequency/1000);
+
+ rc = cpufreq_register_driver(&g5_cpufreq_driver);
+
+ /* We keep the CPU node on hold... hopefully, Apple G5 don't have
+ * hotplug CPU with a dynamic device-tree ...
+ */
+ return rc;
+
+ bail_noprops:
+ of_node_put(cpunode);
+
+ return rc;
+}
+
+module_init(g5_cpufreq_init);
+
+
+MODULE_LICENSE("GPL");
Index: linux-work/drivers/macintosh/smu.c
===================================================================
--- linux-work.orig/drivers/macintosh/smu.c 2005-09-20 13:05:11.000000000 +1000
+++ linux-work/drivers/macintosh/smu.c 2005-09-21 14:34:52.000000000 +1000
@@ -843,6 +843,18 @@
return 0;
}
+struct smu_sdbp_header *smu_get_sdb_partition(int id, unsigned int *size)
+{
+ char pname[32];
+
+ if (!smu)
+ return NULL;
+
+ sprintf(pname, "sdb-partition-%02x", id);
+ return (struct smu_sdbp_header *)get_property(smu->of_node,
+ pname, size);
+}
+EXPORT_SYMBOL(smu_get_sdb_partition);
/*
Index: linux-work/include/asm-ppc64/smu.h
===================================================================
--- linux-work.orig/include/asm-ppc64/smu.h 2005-09-20 11:57:47.000000000 +1000
+++ linux-work/include/asm-ppc64/smu.h 2005-09-21 14:21:13.000000000 +1000
@@ -144,7 +144,11 @@
* - lenght 8 ("VSLEWxyz") has 3 additional bytes appended, and is
* used to set the voltage slewing point. The SMU replies with "DONE"
* I yet have to figure out their exact meaning of those 3 bytes in
- * both cases.
+ * both cases. They seem to be:
+ * x = processor mask
+ * y = op. point index
+ * z = processor freq. step index
+ * I haven't yet decyphered result codes
*
*/
#define SMU_CMD_POWER_COMMAND 0xaa
@@ -244,6 +248,7 @@
*/
extern void smu_done_complete(struct smu_cmd *cmd, void *misc);
+
/*
* Synchronous helpers. Will spin-wait for completion of a command
*/
@@ -334,6 +339,59 @@
#endif /* __KERNEL__ */
/*
+ * - SMU "sdb" partitions informations -
+ */
+
+
+/*
+ * Partition header format
+ */
+struct smu_sdbp_header {
+ __u8 id;
+ __u8 len;
+ __u8 version;
+ __u8 flags;
+};
+
+/*
+ * 32 bits integers are usually encoded with 2x16 bits swapped,
+ * this demangles them
+ */
+#define SMU_U32_MIX(x) ((((x) << 16) & 0xffff0000u) | (((x) >> 16) & 0xffffu))
+
+/* This is the definition of the SMU sdb-partition-0x12 table (called
+ * CPU F/V/T operating points in Darwin). The definition for all those
+ * SMU tables should be moved to some separate file
+ */
+#define SMU_SDB_FVT_ID 0x12
+
+struct smu_sdbp_fvt {
+ __u32 sysclk; /* Base SysClk frequency in Hz for
+ * this operating point
+ */
+ __u8 pad;
+ __u8 maxtemp; /* Max temp. supported by this
+ * operating point
+ */
+
+ __u16 volts[3]; /* CPU core voltage for the 3
+ * PowerTune modes, a mode with
+ * 0V = not supported.
+ */
+};
+
+#ifdef __KERNEL__
+/*
+ * This returns the pointer to an SMU "sdb" partition data or NULL
+ * if not found. The data format is described below
+ */
+extern struct smu_sdbp_header *smu_get_sdb_partition(int id,
+ unsigned int *size);
+
+#endif /* __KERNEL__ */
+
+
+/*
* - Userland interface -
*/
@@ -376,4 +434,5 @@
__u32 reply_len; /* Lenght of data follwing */
};
+
#endif /* _SMU_H */
More information about the Linuxppc64-dev
mailing list