U-Boot 1.3.0 with Linux 2.6.25-11 on MPC8641D - Machine checkexception
Kevin Dockan
Kevin.Dockan at plexus.com
Tue Sep 16 15:01:14 EST 2008
Hello everybody,
I am trying to put into operation a proprietary board using a freescale MPC8641D. I use U-boot 1.3.0 and Linux kernel 2.6.25-11.
On one PCIe-bus I have a PEX8518 followed by a PEX8114. A USB-controller is connected to the 8114.
+--------------------------+
| |
| MPC 8641 D |
| |
+--------------------------+
|
PEX8518 <----------------- PCIe switch
|
PEX8114 <----------------- PCIe to PCI bridge
|
ISP1562 <----------------- USB controller
The PCIe-components are scanned correctly, resources (mem and IO) are assigned (correctly as far as I understand),
but on the first read access to a control register of the usb-device the kernel generates "Oops: Machine check, sig: 7 [#1]".
Writing to the same register does not produce an "Oops".
The PCIe bus is defined in dts file as follows (dump from U-boot):
pcie at d4008000 {
cell-index = <0>;
compatible = "fsl,mpc8641-pcie";
device_type = "pci";
#interrupt-cells = <1>;
#size-cells = <2>;
#address-cells = <3>;
reg = <1000>;
bus-range = <4>;
ranges = [02 00 00 00 00 00 00 00 40 00 00 00 40 00 00 00 00 00 00 00 40 00 00 00 01 00 00 00 00 00 00 00 c0 00 00 00 c0 00 00 00 00 00 00 00 00 10 00 00];
clock-frequency = <1fca055>;
interrupt-parent = <40000>;
interrupts = <2>;
interrupt-map-mask = [00 00 ff 00 00 00 00 00 00 00 00 00 00 00 00 07];
interrupt-map = [00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 01 00 04 00 00 00 00 00 00 00 00 00 01 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 02 00 04 00 00 00 00 00 01 00 00 00 01 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 03 00 04 00 00 00 00 00 02 00 00 00 01 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 04 00 04 00 00 00 00 00 03 00 00 00 01];
pcie at 0 {
reg = [00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00];
#size-cells = <2>;
#address-cells = <3>;
device_type = "pci";
ranges = [02 00 00 00 00 00 00 00 40 00 00 00 02 00 00 00 00 00 00 00 40 00 00 00 00 00 00 00 40 00 00 00 01 00 00 00 00 00 00 00 c0 00 00 00 01 00 00 00 00 00 00 00 c0 00 00 00 00 00 00 00 00 10 00 00];
};
};
pcie at d4009000 {
cell-index = <1>;
compatible = "fsl,mpc8641-pcie";
device_type = "pci";
#interrupt-cells = <1>;
#size-cells = <2>;
#address-cells = <3>;
reg = <1000>;
bus-range = <6>;
ranges = [02 00 00 00 00 00 00 00 80 00 00 00 80 00 00 00 00 00 00 00 40 00 00 00 01 00 00 00 00 00 00 00 c0 10 00 00 c0 10 00 00 00 00 00 00 00 10 00 00];
clock-frequency = <1fca055>;
interrupt-parent = <40000>;
interrupts = <2>;
interrupt-map-mask = [00 00 f8 00 00 00 00 00 00 00 00 00 00 00 00 07];
interrupt-map = [00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 01 00 04 00 00 00 00 00 04 00 00 00 01 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 02 00 04 00 00 00 00 00 05 00 00 00 01 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 03 00 04 00 00 00 00 00 06 00 00 00 01 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 04 00 04 00 00 00 00 00 07 00 00 00 01];
pcie at 0 {
reg = [00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00];
#size-cells = <2>;
#address-cells = <3>;
device_type = "pci";
ranges = [02 00 00 00 00 00 00 00 80 00 00 00 02 00 00 00 00 00 00 00 80 00 00 00 00 00 00 00 40 00 00 00 01 00 00 00 00 00 00 00 c0 10 00 00 01 00 00 00 00 00 00 00 c0 10 00 00 00 00 00 00 00 10 00 00];
};
};
and here the output from kernel:
quirk_usb_handoff_ohci: resource start = 0x80000000, len = 0x00001000
quirk_usb_handoff_ohci: base = 0xe1056000, offset = 0x00000004
Machine check in kernel mode.
Caused by (from SRR1=149030): Transfer error ack signal
Oops: Machine check, sig: 7 [#1]
TAURUS
NIP: c0297f4c LR: c0297f44 CTR: c00115d0
REGS: df821e60 TRAP: 0200 Not tainted (2.6.25.11)
MSR: 00149030 <EE,ME,IR,DR> CR: 24000022 XER: 00000000
TASK = df805410[1] 'swapper' THREAD: df820000
GPR00: c0297f44 df821f10 df805410 00000042 00000001 00000001 00000000 00020000
GPR08: 00000036 c0333fe4 00006b61 c0360000 44000028 f7fbfffc 0fffac00 ffffffff
GPR16: 00800000 007fff00 df821f78 c02d0000 c0330000 c0330000 00000000 0fff5464
GPR24: c0330000 c02d0000 00000000 00000000 e1056000 df841218 df841218 e1056004
NIP [c0297f4c] 0xc0297f4c
LR [c0297f44] 0xc0297f44
Call Trace:
[df821f10] [c0297f44] 0xc0297f44 (unreliable)
[df821f40] [c01617dc] pci_fixup_device+0xec/0x140
[df821f60] [c0295ae0] 0xc0295ae0
[df821f70] [c030c198] kernel_init+0x9c/0x290
[df821ff0] [c0010a6c] kernel_thread+0x44/0x60
Instruction dump:
XXXXXXXX XXXXXXXX XXXXXXXX XXXXXXXX XXXXXXXX XXXXXXXX XXXXXXXX XXXXXXXX
XXXXXXXX XXXXXXXX XXXXXXXX XXXXXXXX XXXXXXXX XXXXXXXX XXXXXXXX XXXXXXXX
---[ end trace 97996e90be8a1237 ]---
Kernel panic - not syncing: Attempted to kill init!
Rebooting in 180 seconds..
where resource start = 0x80000000 is the physical address of the USB controller, base = 0xe1056000 is the virtual address.
Does anyone know this kind of problem and can give me a hint.
Kind Regards,
Joachim
--
Dipl.-Ing. Joachim Bader
Research & Technology
Cockpit and Display Systems
Diehl Aerospace GmbH
An der Sandelmuehle 13
D-60439 Frankfurt
Phone +49-69-5805-1270
Fax +49-69-5805-1400
e-mail: joachim.bader at diehl-aerospace.de
http://www.diehl-aerospace.de
_______________________________________________________________________________________________________________________
Der Inhalt dieser E-Mail ist für den Absender rechtlich nicht verbindlich.
Informieren Sie uns bitte, wenn Sie diese E-Mail fälschlicherweise erhalten haben (Fax: +49-69-5805-1399). Bitte löschen Sie in diesem Fall die Nachricht. Jede Form der weiteren Benutzung ist untersagt.
The content of this e-mail is not legally binding upon the sender.
If this e-mail was transmitted to you by error, then please inform us accordingly (Fax: +49-69-5805-1399). In such case you are requested to erase the message. Any use of such e-mail message is strictly prohibited.
-------------- next part --------------
An HTML attachment was scrubbed...
URL: <http://ozlabs.org/pipermail/linuxppc-embedded/attachments/20080916/a6de1125/attachment.htm>
More information about the Linuxppc-embedded
mailing list