need help with GPIO
Marco Stornelli
marco.stornelli at coritel.it
Wed Sep 3 16:37:48 EST 2008
Hi,
try to understand why the driver doesn't find the device reading the
gpio.c and of_get_gpio(). Maybe the device has been registered as a
platform device and, instead, the driver calls some function for a
specific device.
Regards.
Laxmikant Rashinkar ha scritto:
> Hi Marco,
>
> thanks for your feedback.
>
> I tried out your suggestion of using an offset address instead of an absolute address in the dts, but that did not help.
> I am still getting the error:
>
> LK_DEBUG: gpio.c : of_get_gpio : /localbus/upm at 1,0: gpio controller /soc8349 at e0000000/gpio-controller at c00: is not registered
>
> thanks
> LK
>
>
>
>
> ----- Original Message ----
> From: Marco Stornelli <marco.stornelli at coritel.it>
> To: Laxmikant Rashinkar <lk.atwork at yahoo.com>
> Cc: linuxppc-embedded at ozlabs.org
> Sent: Monday, September 1, 2008 11:39:05 PM
> Subject: Re: need help with GPIO
>
> Laxmikant Rashinkar ha scritto:
>
>> Hi,
>>
>> I have a MPC8347 based embedded PC running Linux 2.6.27.
>> I am trying to access a NAND device connected to the LBC and UPM.
>> The Ready/Busy* pin of the NAND device is connected to the built in GPIO-1 on pin 4 (input).
>>
>> When I try to access the NAND device, the function of_get_gpio() from drivers/of/gpio.c gets called, and
>> it reports that my GPIO is not registered. Here are the actual debug messages:
>>
>> LK_DEBUG: gpio.c : of_get_gpio : name=upm type=<NULL> index=0
>> LK_DEBUG: gpio.c : of_get_gpio : got property
>> LK_DEBUG: gpio.c : of_get_gpio : nr_cell=3
>> LK_DEBUG: gpio.c : of_get_gpio : gc.name=gpio-controller gc.type=<NULL> gc->Data=0x0
>> LK_DEBUG: gpio.c : of_get_gpio : /localbus/upm at 1,0: gpio controller /soc8349 at e0000000/gpio-controller at e0000c00: is not registered
>>
>> When I check in /proc/device-tree/soc8349 at e0000000/, I find that entries are present for both GPIOs are present.
>>
>> Here are debug registration messages, indicating that gpio registered successfully:
>>
>> ##### LK_DEBUG: of_plat_dev_create : NAME=soc8349
>> ##### LK_DEBUG: of_plat_dev_create : NAME=wdt
>> ##### LK_DEBUG: of_plat_dev_create : NAME=i2c
>> ##### LK_DEBUG: of_plat_dev_create : NAME=i2c
>> ##### LK_DEBUG: of_plat_dev_create : NAME=spi
>> ##### LK_DEBUG: of_plat_dev_create : NAME=dma
>> ##### LK_DEBUG: of_plat_dev_create : NAME=usb
>> ##### LK_DEBUG: of_plat_dev_create : NAME=usb
>> ##### LK_DEBUG: of_plat_dev_create : NAME=mdio
>> ##### LK_DEBUG: of_plat_dev_create : NAME=ethernet
>> ##### LK_DEBUG: of_plat_dev_create : NAME=ethernet
>> ##### LK_DEBUG: of_plat_dev_create : NAME=serial
>> ##### LK_DEBUG: of_plat_dev_create : NAME=serial
>> ##### LK_DEBUG: of_plat_dev_create : NAME=crypto
>> ##### LK_DEBUG: of_plat_dev_create : NAME=pic
>> ##### LK_DEBUG: of_plat_dev_create : NAME=gpio-controller
>> ##### LK_DEBUG: of_plat_dev_create : NAME=gpio-controller
>> ##### LK_DEBUG: of_plat_dev_create : NAME=localbus
>> ##### LK_DEBUG: of_plat_dev_create : NAME=upm
>>
>> Most probably something is wrong in my device tree (listed below). Can someone please point me in the right direction?
>>
>> thanks a lot for your help.
>> LK
>>
>> -------------------------------------------------------------
>>
>> /*
>> * MPC8349E MDS Device Tree Source
>> *
>> * Copyright 2005, 2006 Freescale Semiconductor Inc.
>> *
>> * This program is free software; you can redistribute it and/or modify it
>> * under the terms of the GNU General Public License as published by the
>> * Free Software Foundation; either version 2 of the License, or (at your
>> * option) any later version.
>> */
>>
>> /dts-v1/;
>>
>> / {
>> model = "MPC8349EMDS";
>> compatible = "MPC8349EMDS", "MPC834xMDS", "MPC83xxMDS";
>> #address-cells = <1>;
>> #size-cells = <1>;
>>
>> aliases {
>> ethernet0 = &enet0;
>> ethernet1 = &enet1;
>> serial0 = &serial0;
>> serial1 = &serial1;
>> pci0 = &pci0;
>> pci1 = &pci1;
>> };
>>
>> cpus {
>> #address-cells = <1>;
>> #size-cells = <0>;
>>
>> PowerPC,8349 at 0 {
>> device_type = "cpu";
>> reg = <0x0>;
>> d-cache-line-size = <32>;
>> i-cache-line-size = <32>;
>> d-cache-size = <32768>;
>> i-cache-size = <32768>;
>> timebase-frequency = <0>; // from bootloader
>> bus-frequency = <0>; // from bootloader
>> clock-frequency = <0>; // from bootloader
>> };
>> };
>>
>> memory {
>> device_type = "memory";
>> reg = <0x00000000 0x10000000>; // 256MB at 0
>> };
>>
>> bcsr at e2400000 {
>> device_type = "board-control";
>> reg = <0xe2400000 0x8000>;
>> };
>>
>> soc8349 at e0000000 {
>> #address-cells = <1>;
>> #size-cells = <1>;
>> device_type = "soc";
>> compatible = "simple-bus";
>> ranges = <0x0 0xe0000000 0x00100000>;
>> reg = <0xe0000000 0x00000200>;
>> bus-frequency = <0>;
>>
>> wdt at 200 {
>> device_type = "watchdog";
>> compatible = "mpc83xx_wdt";
>> reg = <0x200 0x100>;
>> };
>>
>> i2c at 3000 {
>> #address-cells = <1>;
>> #size-cells = <0>;
>> cell-index = <0>;
>> compatible = "fsl-i2c";
>> reg = <0x3000 0x100>;
>> interrupts = <14 0x8>;
>> interrupt-parent = <&ipic>;
>> dfsrr;
>>
>> rtc at 68 {
>> compatible = "dallas,ds1374";
>> reg = <0x68>;
>> };
>> };
>>
>> i2c at 3100 {
>> #address-cells = <1>;
>> #size-cells = <0>;
>> cell-index = <1>;
>> compatible = "fsl-i2c";
>> reg = <0x3100 0x100>;
>> interrupts = <15 0x8>;
>> interrupt-parent = <&ipic>;
>> dfsrr;
>> };
>>
>> spi at 7000 {
>> cell-index = <0>;
>> compatible = "fsl,spi";
>> reg = <0x7000 0x1000>;
>> interrupts = <16 0x8>;
>> interrupt-parent = <&ipic>;
>> mode = "cpu";
>> };
>>
>> dma at 82a8 {
>> #address-cells = <1>;
>> #size-cells = <1>;
>> compatible = "fsl,mpc8349-dma", "fsl,elo-dma";
>> reg = <0x82a8 4>;
>> ranges = <0 0x8100 0x1a8>;
>> interrupt-parent = <&ipic>;
>> interrupts = <71 8>;
>> cell-index = <0>;
>> dma-channel at 0 {
>> compatible = "fsl,mpc8349-dma-channel", "fsl,elo-dma-channel";
>> reg = <0 0x80>;
>> interrupt-parent = <&ipic>;
>> interrupts = <71 8>;
>> };
>> dma-channel at 80 {
>> compatible = "fsl,mpc8349-dma-channel", "fsl,elo-dma-channel";
>> reg = <0x80 0x80>;
>> interrupt-parent = <&ipic>;
>> interrupts = <71 8>;
>> };
>> dma-channel at 100 {
>> compatible = "fsl,mpc8349-dma-channel", "fsl,elo-dma-channel";
>> reg = <0x100 0x80>;
>> interrupt-parent = <&ipic>;
>> interrupts = <71 8>;
>> };
>> dma-channel at 180 {
>> compatible = "fsl,mpc8349-dma-channel", "fsl,elo-dma-channel";
>> reg = <0x180 0x28>;
>> interrupt-parent = <&ipic>;
>> interrupts = <71 8>;
>> };
>> };
>>
>> /* phy type (ULPI or SERIAL) are only types supported for MPH */
>> /* port = 0 or 1 */
>> usb at 22000 {
>> compatible = "fsl-usb2-mph";
>> reg = <0x22000 0x1000>;
>> #address-cells = <1>;
>> #size-cells = <0>;
>> interrupt-parent = <&ipic>;
>> interrupts = <39 0x8>;
>> phy_type = "ulpi";
>> port1;
>> };
>> /* phy type (ULPI, UTMI, UTMI_WIDE, SERIAL) */
>> usb at 23000 {
>> compatible = "fsl-usb2-dr";
>> reg = <0x23000 0x1000>;
>> #address-cells = <1>;
>> #size-cells = <0>;
>> interrupt-parent = <&ipic>;
>> interrupts = <38 0x8>;
>> dr_mode = "otg";
>> phy_type = "ulpi";
>> };
>>
>> mdio at 24520 {
>> #address-cells = <1>;
>> #size-cells = <0>;
>> compatible = "fsl,gianfar-mdio";
>> reg = <0x24520 0x20>;
>>
>> phy0: ethernet-phy at 0 {
>> interrupt-parent = <&ipic>;
>> interrupts = <17 0x8>;
>> reg = <0x1>;
>> device_type = "ethernet-phy";
>> };
>> phy1: ethernet-phy at 1 {
>> interrupt-parent = <&ipic>;
>> interrupts = <18 0x8>;
>> reg = <0x2>;
>> device_type = "ethernet-phy";
>> };
>> };
>>
>> enet0: ethernet at 24000 {
>> cell-index = <0>;
>> device_type = "network";
>> model = "TSEC";
>> compatible = "gianfar";
>> reg = <0x24000 0x1000>;
>> local-mac-address = [ 00 00 00 00 00 00 ];
>> interrupts = <32 0x8 33 0x8 34 0x8>;
>> interrupt-parent = <&ipic>;
>> phy-handle = <&phy0>;
>> linux,network-index = <0>;
>> };
>>
>> enet1: ethernet at 25000 {
>> cell-index = <1>;
>> device_type = "network";
>> model = "TSEC";
>> compatible = "gianfar";
>> reg = <0x25000 0x1000>;
>> local-mac-address = [ 00 00 00 00 00 00 ];
>> interrupts = <35 0x8 36 0x8 37 0x8>;
>> interrupt-parent = <&ipic>;
>> phy-handle = <&phy1>;
>> linux,network-index = <1>;
>> };
>>
>> serial0: serial at 4500 {
>> cell-index = <0>;
>> device_type = "serial";
>> compatible = "ns16550";
>> reg = <0x4500 0x100>;
>> clock-frequency = <0>;
>> interrupts = <9 0x8>;
>> interrupt-parent = <&ipic>;
>> };
>>
>> serial1: serial at 4600 {
>> cell-index = <1>;
>> device_type = "serial";
>> compatible = "ns16550";
>> reg = <0x4600 0x100>;
>> clock-frequency = <0>;
>> interrupts = <10 0x8>;
>> interrupt-parent = <&ipic>;
>> };
>>
>> crypto at 30000 {
>> compatible = "fsl,sec2.0";
>> reg = <0x30000 0x10000>;
>> interrupts = <11 0x8>;
>> interrupt-parent = <&ipic>;
>> fsl,num-channels = <4>;
>> fsl,channel-fifo-len = <24>;
>> fsl,exec-units-mask = <0x7e>;
>> fsl,descriptor-types-mask = <0x01010ebf>;
>> };
>>
>> /* IPIC
>> * interrupts cell = <intr #, sense>
>> * sense values match linux IORESOURCE_IRQ_* defines:
>> * sense == 8: Level, low assertion
>> * sense == 2: Edge, high-to-low change
>> */
>> ipic: pic at 700 {
>> interrupt-controller;
>> #address-cells = <0>;
>> #interrupt-cells = <2>;
>> reg = <0x700 0x100>;
>> device_type = "ipic";
>> };
>>
>>
>
> Here you are using absolute addresses but you should use an offset from
> a base reg address, in your case e0000000.
>
>
>> gpio1: gpio-controller at e0000c00 {
>>
> gpio1: gpio-controller at c00 {
>
>> #gpio-cells = <2>;
>> compatible = "fsl,mpc8349-gpio-bank";
>>
> reg = <0xc00 0x100>;
>
>> reg = <0xe0000c00 0x100>;
>> gpio-controller;
>> };
>>
>>
> gpio2: gpio-controller at d00 {
>
>> gpio2: gpio-controller at e0000d00 {
>> #gpio-cells = <2>;
>> compatible = "fsl,mpc8349-gpio-bank";
>>
> reg = <0xd00 0x100>;
>
>> reg = <0xe0000d00 0x100>;
>> gpio-controller;
>> };
>> };
>>
>> localbus {
>> compatible = "fsl,pq3-localbus", "simple-bus";
>> #address-cells = <2>;
>> #size-cells = <1>;
>> reg = <0xe0005000 0x100000>; // BRx, ORx, etc.
>>
>> upm at 1,0 {
>> #address-cells = <1>;
>> #size-cells = <1>;
>> compatible = "fsl,upm-nand";
>> reg = <3 0xa0000000 0x800>;
>> fsl,upm-addr-offset = <0x10>;
>> fsl,upm-cmd-offset = <0x08>;
>> gpios = <&gpio1 4 0>;
>>
>> nand at 0 {
>> #address-cells = <1>;
>> #size-cells = <1>;
>> compatible = "fsl,lbc-nand";
>>
>> partition at 0 {
>> label = "EVERYTHING";
>> reg = <0x00000000 0x01000000>;
>> };
>> };
>> };
>> };
>>
>> pci0: pci at e0008500 {
>> cell-index = <1>;
>> interrupt-map-mask = <0xf800 0x0 0x0 0x7>;
>> interrupt-map = <
>>
>> /* IDSEL 0x11 */
>> 0x8800 0x0 0x0 0x1 &ipic 20 0x8
>> 0x8800 0x0 0x0 0x2 &ipic 21 0x8
>> 0x8800 0x0 0x0 0x3 &ipic 22 0x8
>> 0x8800 0x0 0x0 0x4 &ipic 23 0x8
>>
>> /* IDSEL 0x12 */
>> 0x9000 0x0 0x0 0x1 &ipic 22 0x8
>> 0x9000 0x0 0x0 0x2 &ipic 23 0x8
>> 0x9000 0x0 0x0 0x3 &ipic 20 0x8
>> 0x9000 0x0 0x0 0x4 &ipic 21 0x8
>>
>> /* IDSEL 0x13 */
>> 0x9800 0x0 0x0 0x1 &ipic 23 0x8
>> 0x9800 0x0 0x0 0x2 &ipic 20 0x8
>> 0x9800 0x0 0x0 0x3 &ipic 21 0x8
>> 0x9800 0x0 0x0 0x4 &ipic 22 0x8
>>
>> /* IDSEL 0x15 */
>> 0xa800 0x0 0x0 0x1 &ipic 20 0x8
>> 0xa800 0x0 0x0 0x2 &ipic 21 0x8
>> 0xa800 0x0 0x0 0x3 &ipic 22 0x8
>> 0xa800 0x0 0x0 0x4 &ipic 23 0x8
>>
>> /* IDSEL 0x16 */
>> 0xb000 0x0 0x0 0x1 &ipic 23 0x8
>> 0xb000 0x0 0x0 0x2 &ipic 20 0x8
>> 0xb000 0x0 0x0 0x3 &ipic 21 0x8
>> 0xb000 0x0 0x0 0x4 &ipic 22 0x8
>>
>> /* IDSEL 0x17 */
>> 0xb800 0x0 0x0 0x1 &ipic 22 0x8
>> 0xb800 0x0 0x0 0x2 &ipic 23 0x8
>> 0xb800 0x0 0x0 0x3 &ipic 20 0x8
>> 0xb800 0x0 0x0 0x4 &ipic 21 0x8
>>
>> /* IDSEL 0x18 */
>> 0xc000 0x0 0x0 0x1 &ipic 21 0x8
>> 0xc000 0x0 0x0 0x2 &ipic 22 0x8
>> 0xc000 0x0 0x0 0x3 &ipic 23 0x8
>> 0xc000 0x0 0x0 0x4 &ipic 20 0x8>;
>> interrupt-parent = <&ipic>;
>> interrupts = <66 0x8>;
>> bus-range = <0 0>;
>> ranges = <0x02000000 0x0 0x90000000 0x90000000 0x0 0x10000000
>> 0x42000000 0x0 0x80000000 0x80000000 0x0 0x10000000
>> 0x01000000 0x0 0x00000000 0xe2000000 0x0 0x00100000>;
>> clock-frequency = <66666666>;
>> #interrupt-cells = <1>;
>> #size-cells = <2>;
>> #address-cells = <3>;
>> reg = <0xe0008500 0x100>;
>> compatible = "fsl,mpc8349-pci";
>> device_type = "pci";
>> };
>>
>> pci1: pci at e0008600 {
>> cell-index = <2>;
>> interrupt-map-mask = <0xf800 0x0 0x0 0x7>;
>> interrupt-map = <
>>
>> /* IDSEL 0x11 */
>> 0x8800 0x0 0x0 0x1 &ipic 20 0x8
>> 0x8800 0x0 0x0 0x2 &ipic 21 0x8
>> 0x8800 0x0 0x0 0x3 &ipic 22 0x8
>> 0x8800 0x0 0x0 0x4 &ipic 23 0x8
>>
>> /* IDSEL 0x12 */
>> 0x9000 0x0 0x0 0x1 &ipic 22 0x8
>> 0x9000 0x0 0x0 0x2 &ipic 23 0x8
>> 0x9000 0x0 0x0 0x3 &ipic 20 0x8
>> 0x9000 0x0 0x0 0x4 &ipic 21 0x8
>>
>> /* IDSEL 0x13 */
>> 0x9800 0x0 0x0 0x1 &ipic 23 0x8
>> 0x9800 0x0 0x0 0x2 &ipic 20 0x8
>> 0x9800 0x0 0x0 0x3 &ipic 21 0x8
>> 0x9800 0x0 0x0 0x4 &ipic 22 0x8
>>
>> /* IDSEL 0x15 */
>> 0xa800 0x0 0x0 0x1 &ipic 20 0x8
>> 0xa800 0x0 0x0 0x2 &ipic 21 0x8
>> 0xa800 0x0 0x0 0x3 &ipic 22 0x8
>> 0xa800 0x0 0x0 0x4 &ipic 23 0x8
>>
>> /* IDSEL 0x16 */
>> 0xb000 0x0 0x0 0x1 &ipic 23 0x8
>> 0xb000 0x0 0x0 0x2 &ipic 20 0x8
>> 0xb000 0x0 0x0 0x3 &ipic 21 0x8
>> 0xb000 0x0 0x0 0x4 &ipic 22 0x8
>>
>> /* IDSEL 0x17 */
>> 0xb800 0x0 0x0 0x1 &ipic 22 0x8
>> 0xb800 0x0 0x0 0x2 &ipic 23 0x8
>> 0xb800 0x0 0x0 0x3 &ipic 20 0x8
>> 0xb800 0x0 0x0 0x4 &ipic 21 0x8
>>
>> /* IDSEL 0x18 */
>> 0xc000 0x0 0x0 0x1 &ipic 21 0x8
>> 0xc000 0x0 0x0 0x2 &ipic 22 0x8
>> 0xc000 0x0 0x0 0x3 &ipic 23 0x8
>> 0xc000 0x0 0x0 0x4 &ipic 20 0x8>;
>> interrupt-parent = <&ipic>;
>> interrupts = <67 0x8>;
>> bus-range = <0 0>;
>> ranges = <0x02000000 0x0 0xb0000000 0xb0000000 0x0 0x10000000
>> 0x42000000 0x0 0xa0000000 0xa0000000 0x0 0x10000000
>> 0x01000000 0x0 0x00000000 0xe2100000 0x0 0x00100000>;
>> clock-frequency = <66666666>;
>> #interrupt-cells = <1>;
>> #size-cells = <2>;
>> #address-cells = <3>;
>> reg = <0xe0008600 0x100>;
>> compatible = "fsl,mpc8349-pci";
>> device_type = "pci";
>> };
>>
>> chosen {
>> linux,stdout-path = &serial0;
>> };
>> };
>>
>>
>>
>>
>>
>> ------------------------------------------------------------------------
>>
>> _______________________________________________
>> Linuxppc-embedded mailing list
>> Linuxppc-embedded at ozlabs.org
>> https://ozlabs.org/mailman/listinfo/linuxppc-embedded
>>
>
>
>
> ------------------------------------------------------------------------
>
> _______________________________________________
> Linuxppc-embedded mailing list
> Linuxppc-embedded at ozlabs.org
> https://ozlabs.org/mailman/listinfo/linuxppc-embedded
--
Marco Stornelli
Embedded Software Engineer
CoRiTeL - Consorzio di Ricerca sulle Telecomunicazioni
http://www.coritel.it
marco.stornelli at coritel.it
+39 06 72582838
More information about the Linuxppc-embedded
mailing list