problems loading 2.6.25 kernel into PQ2FADS-VR board

Jyotshna Cherukuri jcherukuri_necc at yahoo.com
Thu Nov 20 03:04:46 EST 2008


Hi ,

I am trying to port 2.6.25 kernel and RFS with NFS onto PQ2FADS-VR board and I run into following error when I boot the image with u-boot 1.3.2

Could anyone please let me know to how I need to debug the following error ?

Any help is greatly appreciated in this regards.

Thanks
Jyotshna

=> bootm 400000 - 800000

## Booting image at 00400000 ...

   Image Name:   Linux-2.6.25

   Image Type:   PowerPC Linux Kernel Image (gzip compressed)

   Data Size:    1339847 Bytes =  1.3 MB

   Load Address: 00000000

   Entry Point:  00000000

   Verifying Checksum ... OK

   Uncompressing Kernel Image ... OK

   Booting using the fdt at 0x800000

   Loading Device Tree to 007fc000, end 007fefff ... OK

Xid mach(): done

MMU:enter

MMU:hw init

MMU:mapin

MMU:setio

MMU:exit

Using Freescale PQ2FADS machine description

Linux version 2.6.25 (jcherukuri at localhost.localdomain) (gcc version 4.2.1 (Sourcery G++ Lite 4.2-82)) #52 Tue Nov 18 17:15:13 EST 2008

console [udbg0] enabled

Entering add_active_range(0, 0, 8192) 0 entries of 256 used

setup_arch: bootmem

pq2fads_setup_arch()

PCI host bridge /pci at f0010800 (primary) ranges:

 MEM 0x0000000080000000..0x000000009fffffff -> 0x0000000080000000 Prefetch

 MEM 0x00000000a0000000..0x00000000bfffffff -> 0x00000000a0000000

  IO 0x00000000f6000000..0x00000000f7ffffff -> 0x0000000000000000

pq2fads_setup_arch(), finish

arch: exit

Top of RAM: 0x2000000, Total RAM: 0x2000000

Memory hole size: 0MB

Zone PFN ranges:

  DMA             0 ->     8192

  Normal       8192 ->     8192

Movable zone start PFN for each node

early_node_map[1] active PFN ranges

    0:        0 ->     8192

On node 0 totalpages: 8192

  DMA zone: 64 pages used for memmap

  DMA zone: 0 pages reserved

  DMA zone: 8128 pages, LIFO batch:0

  Normal zone: 0 pages used for memmap

  Movable zone: 0 pages used for memmap

Built 1 zonelists in Zone order, mobility grouping on.  Total pages: 8128

Kernel command line: root=/dev/nfs ip=192.168.10.112:192.168.10.115::::eth0:off console=ttyCPM0,38400n8 nfsroot=/tftpboot/192.168.10.112.LTIB

PID hash table entries: 128 (order: 7, 512 bytes)

time_init: decrementer frequency = 16.500000 MHz

time_init: processor frequency   = 264.000000 MHz

clocksource: timebase mult[f26c9b2] shift[22] registered

clockevent: decrementer mult[439] shift[16] cpu[0]

Console: colour dumm?Dentry cache hash table entries: 4096 (order: 2, 16384 bytes)

Inode-cache hash table entries: 2048 (order: 1, 8192 bytes)

Memory: 29572k/32768k available (2640k kernel code, 3196k reserved, 104k data, 91k bss, 104k init)

SLUB: Genslabs=12, HWalign=32, Order=0-1, MinObjects=4, CPUs=1, Nodes=1

Calibrating delay loop... 32.89 BogoMIPS (lpj=65792)

Mount-cache hash table entries: 512

net_namespace: 440 bytes

NET: Registered protocol family 16

PCI: Probing PCI hardware

Can't get bus-range for /pci at f0010800, assuming it starts at 0

NET: Registered protocol family 2

IP route cache hash table entries: 1024 (order: 0, 4096 bytes)

TCP established hash table entries: 1024 (order: 1, 8192 bytes)

TCP bind hash table entries: 1024 (order: 0, 4096 bytes)

TCP: Hash tables configured (established 1024 bind 1024)

TCP reno registered

JFFS2 version 2.2. .. 2001-2006 Red Hat, Inc.

io scheduler noop registered

io scheduler anticipatory registered

io scheduler deadline registered

io scheduler cfq registered (default)

pci_hotplug: PCI Hot Plug PCI Core version: 0.5

ttyCPM0 at MMIO 0xf0011a00 (irq = 40) is a CPM UART

ttyCPM1 at MMIO 0xf0011a20 (irq = 41) is a CPM UART

loop: module loaded

eth0: fs_enet: 00:e0:0a:0b:79:01

eth1: fs_enet: 00:e0:0c:00:79:01

CPM2 Bitbanged MII: probed

physmap platform flash device: 00800000 at ff800000

CFI: Found no physmap-flash.0 device at location zero

physmap-flash physmap-flash.0: map_probe failed

of-flash fe000000.flash: do_map_probe() failed

mice: PS/2 mouse device common for all mice

TCP cubic registered

NET: Registered protocol family 1

NET: Registered protocol family 17

RPC: Registered udp transport module.

RPC: Registered tcp transport module.

IP-Config: Guessing netmask 255.255.255.0

IP-Config: Complete:

     device=eth0, addr=192.168.10.112, mask=255.255.255.0, gw=255.255.255.255,

     host=192.168.10.112, domain=, nis-domain=(none),

     bootserver=192.168.10.115, rootserver=192.168.10.115, rootpath=

Looking up port of RPC 100003/2 on 192.168.10.115

Looking up port of RPC 100005/1 on 192.168.10.115

VFS: Mounted root (nfs filesystem) readonly.

Freeing unused kernel memory: 104k init

Warning: unable to open an initial console.

Kernel panic - not syncing: No init found.  Try passing init= option to kernel.

Rebooting in 180 seconds..








      
-------------- next part --------------
An HTML attachment was scrubbed...
URL: <http://ozlabs.org/pipermail/linuxppc-embedded/attachments/20081119/fad11ecd/attachment-0001.htm>


More information about the Linuxppc-embedded mailing list