Linux 2.6 boot failure on xup virtex II ppc405
saadia dhouib
saadia_dhouib at yahoo.fr
Sat Nov 1 03:21:50 EST 2008
Hi all,
After booting successfully the kernel without a root file system.
I installed a file system on the flash disk. I used: BusyBox 1.12.1, and
the script mkrootfs.sh (written by
Wofgang Klingauf) to generate the rfs.
I changed the boot arg in the kernel configuration as follows:
[*] Default bootloader kernel arguments
│ │
│ │ (console=ttyUL0,9600
root=/dev/xsysace/disc0/xsa3 rw) Initial kernel command string
Then I rebooted the kernel, and there were those errors :( :
Linux/PowerPC load: console=ttyUL0,9600 root=/dev/xsysace/disc0/part3 ip=on
Finalizing device tree... flat tree at 0x40ae18
Using Xilinx Virtex machine description
Linux version 2.6.27-rc9 (dhouib at lo-lester-030) (gcc version 3.4.5) #19
PREEMPT Fri Oct 31 15:41:03 CET 2008
Zone PFN ranges:
DMA 0x00000000 -> 0x00010000
Normal 0x00010000 -> 0x00010000
Movable zone start PFN for each node
early_node_map[1] active PFN ranges
0: 0x00000000 -> 0x00010000
Built 1 zonelists in Zone order, mobility grouping on. Total pages: 65024
Kernel command line: console=ttyUL0,9600 root=/dev/xsysace/disc0/part3 ip=on
Xilinx intc at 0x41200000 mapped to 0xfdfff000
PID hash table entries: 1024 (order: 10, 4096 bytes)
clocksource: timebase mult[d55555] shift[22] registered
Console: colour dummy device 80x25
console [ttyUL0] enabled
Dentry cache hash table entries: 32768 (order: 5, 131072 bytes)
Inode-cache hash table entries: 16384 (order: 4, 65536 bytes)
Memory: 257792k/262144k available (1564k kernel code, 4044k reserved, 84k
data, 89k bss, 76k init)
Calibrating delay loop... 598.01 BogoMIPS (lpj=1196032)
Mount-cache hash table entries: 512
msgmni has been set to 504
io scheduler noop registered
io scheduler anticipatory registered
io scheduler deadline registered
io scheduler cfq registered (default)
40600000.serial: ttyUL0 at MMIO 0x40600003 (irq = 16) is a uartlite
xsysace 41800000.sysace: Xilinx SystemACE revision 1.0.12
xsysace 41800000.sysace: capacity: 3940272 sectors
xsa: xsa1 xsa2 xsa3
Xilinx SystemACE device driver, major=254
mice: PS/2 mouse device common for all mice
VFS: Cannot open root device "xsysace/disc0/part3" or unknown-block(0,0)
Please append a correct "root=" boot option; here are the available
partitions:
fe00 1970136 xsa (driver?)
fe01 32098 xsa1
fe02 265072 xsa2
fe03 1020127 xsa3
Kernel panic - not syncing: VFS: Unable to mount root fs on
unknown-block(0,0)
Rebooting in 180 seconds..<2>init has generated signal 8 but has no handler
for it
note: swapper[1] exited with preempt_count 2
Kernel panic - not syncing: Attempted to kill init!
Rebooting in 180 seconds..Oops: Exception in kernel mode, sig: 8 [#1]
PREEMPT Xilinx Virtex
NIP: cf80ab60 LR: cf81fba0 CTR: 00000000
REGS: cf81faf0 TRAP: cf81fba0 Not tainted (2.6.27-rc9)
MSR: 00000020 <IR> CR: 44004022 XER: cf80ab68
TASK = cf814c00[1] 'swapper' THREAD: cf81e000
GPR00: 44000084 cf81fb50 00000006 c0190000 00029030 c0190000 00000030
cf81e000
GPR08: cf81fb20 004ca564 c01a0000 c01a0000 c01621a0 cf81fc58 cf814c00
cf81fd20
GPR16: c01a0000 c01648c0 cf814c00 c01a0000 cf81fbc0 c0026428 00000039
000000b4
GPR24: c01a4d70 ffffffff 00000000 000009b8 00000004 00000000 00000000
c01a0000
NIP [cf80ab60] 0xcf80ab60
LR [cf81fba0] 0xcf81fba0
Call Trace:
[cf81fb50] [ffffffff] 0xffffffff (unreliable)
Instruction dump:
XXXXXXXX XXXXXXXX XXXXXXXX XXXXXXXX XXXXXXXX XXXXXXXX XXXXXXXX XXXXXXXX
XXXXXXXX XXXXXXXX XXXXXXXX XXXXXXXX XXXXXXXX XXXXXXXX XXXXXXXX XXXXXXXX
---[ end trace 17f4c6d1c47d3b7d ]---
Fixing recursive fault but reboot is needed!
BUG: scheduling while atomic: swapper/1/0x00000003
Call Trace:
[cf81f8a0] [c0007704] show_stack+0x40/0x16c (unreliable)
[cf81f8d0] [c0020150] __schedule_bug+0x64/0x78
[cf81f8f0] [c013d108] __sched_text_start+0x390/0x3fc
[cf81f930] [c0027f10] do_exit+0x440/0x7b0
[cf81f970] [c000b594] _exception+0x0/0x1ac
[cf81f990] [c000b6a8] _exception+0x114/0x1ac
[cf81fae0] [c000e0fc] ret_from_except_full+0x0/0x4c
[cf81fb20] [cf81fc58] 0xcf81fc58
Could someone help me please?
Thanks
Saadia
saadia dhouib wrote:
>
> Hi,
> I have downloaded the latest linux kernel linux-2.6-xlnx.git from
> http://git.xilinx.com/ .
> Than I have downloaded the device tree generator device-tree.git from the
> same site.
> I launched edk 8.2.02, I designed a system with two powerpc cores:
> ppc_405_0, ppc_405_1, and opb bus , a plb bus, and the following devices
> with their memory map:
>
> BASE HIGH MODULE
> 0x00000000 0x0FFFFFFF DDR_256MB_32MX64_rank1_row13_col10_cl2_5
> 0x40600000 0x4060FFFF RS232_Uart_1
> 0x40C00000 0x40C0FFFF Ethernet_MAC
> 0x41200000 0x4120FFFF opb_intc_0
> 0x41800000 0x4180FFFF SysACE_CompactFlash
>
> I generated the bitsteam system.bit.
> After getting the device tree generator from
> git://git.xilinx.com/device-tree.git, I have copied the 'bsp' directory
> and contents so that it can be used by edk XPS. Then I selected
> 'device-tree' in the pull down menu labeled 'OS' in the Software Platform
> Settings dialog box.
> Then selected 'OS and Libraries' on the left, and entered the values for
> 'console device' and 'bootargs' (respectively
> 'RS232_Uart_1' and 'console=ttyS0,9600 root=/dev/xsysace/disc0/part3
> ip=on' ).
> Then I generated libraries and BSP, in the edk_project directory and not
> in the linux src directory.
> There were those warnings:
> *******************************************************************************************************************
> --- device tree generator version: v1.1 ---
> generating xilinx.dts
> Clock Port Summary:
> ppc405_0.CPMC405CLOCK connected to proc_clk_s:
> CLK_FREQ_HZ = WARNING: no frequency found!
> ppc405_0.PLBCLK connected to sys_clk_s:
> CLK_FREQ_HZ = WARNING: no frequency found!
> reset_block.Slowest_sync_clk connected to sys_clk_s:
> CLK_FREQ_HZ = WARNING: no frequency found!
> plb.PLB_Clk connected to sys_clk_s:
> CLK_FREQ_HZ = WARNING: no frequency found!
> opb.OPB_Clk connected to sys_clk_s:
> CLK_FREQ_HZ = WARNING: no frequency found!
>
> plb2opb.PLB_Clk connected to sys_clk_s:
> CLK_FREQ_HZ = WARNING: no frequency found!
> plb2opb.OPB_Clk connected to sys_clk_s:
> CLK_FREQ_HZ = WARNING: no frequency found!
> RS232_Uart_1.OPB_Clk connected to sys_clk_s:
> CLK_FREQ_HZ = WARNING: no frequency found!
> Ethernet_MAC.OPB_Clk connected to sys_clk_s:
> CLK_FREQ_HZ = WARNING: no frequency found!
> SysACE_CompactFlash.OPB_Clk connected to sys_clk_s:
> CLK_FREQ_HZ = WARNING: no frequency found!
> DDR_256MB_32MX64_rank1_row13_col10_cl2_5.PLB_Clk connected to sys_clk_s:
> CLK_FREQ_HZ = WARNING: no frequency found!
> plb_bram_if_cntlr_1.plb_clk connected to sys_clk_s:
> CLK_FREQ_HZ = WARNING: no frequency found!
> plb_bram_if_cntlr_1_bram.BRAM_Clk_A connected to
> plb_bram_if_cntlr_1_port_BRAM_Clk:
> CLK_FREQ_HZ = WARNING: no frequency found!
> opb_intc_0.OPB_Clk connected to sys_clk_s:
> CLK_FREQ_HZ = WARNING: no frequency found!
> dcm_0.CLKIN connected to dcm_clk_s:
> CLK_FREQ_HZ = WARNING: no frequency found!
> dcm_0.CLK0 connected to sys_clk_s:
> CLK_FREQ_HZ = WARNING: no frequency found!
> CLK_INPORT = CLKIN
> CLK_FACTOR = 1
> dcm_0.CLK90 connected to clk_90_s:
> CLK_FREQ_HZ = WARNING: no frequency found!
> CLK_INPORT = CLKIN
> CLK_FACTOR = 1
> dcm_0.CLKFX connected to proc_clk_s:
> CLK_FREQ_HZ = WARNING: no frequency found!
> CLK_INPORT = CLKIN
> CLK_FACTOR = C_CLKFX_MULTIPLY / C_CLKFX_DIVIDE
> dcm_1.CLKIN connected to ddr_feedback_s:
> CLK_FREQ_HZ = WARNING: no frequency found!
> dcm_1.CLK0 connected to dcm_1_FB:
> CLK_FREQ_HZ = WARNING: no frequency found!
> CLK_INPORT = CLKIN
> CLK_FACTOR = 1
> dcm_1.CLK90 connected to ddr_clk_90_s:
> CLK_FREQ_HZ = WARNING: no frequency found!
> CLK_INPORT = CLKIN
> CLK_FACTOR = 1
> Clock Frequency: 300000000
> IP connected to bus: plb
> -master DPLB plb ppc405_0
> -master IPLB plb ppc405_0
> -slave SPLB plb plb2opb
> -slave SPLB plb DDR_256MB_32MX64_rank1_row13_col10_cl2_5
> -slave SPLB plb plb_bram_if_cntlr_1
> IP connected to bus: opb
> -master MOPB opb plb2opb
> -slave SOPB opb RS232_Uart_1
> -slave SOPB opb Ethernet_MAC
> -slave SOPB opb SysACE_CompactFlash
> -slave SOPB opb opb_intc_0
>
> WARNING:MDT - Search path /home/dhouib/xupv2p/ directly contains pcores
> directory. Search path should point to a directory two levels above
> pcores.
> WARNING:MDT - Search path /home/dhouib/xupv2p/ directly contains pcores
> directory. Search path should point to a directory two levels above
> pcores.
> CLK_FREQ_HZ = WARNING: no frequency found!
>
> CLK_FREQ_HZ = WARNING: no frequency found!
>
> CLK_FREQ_HZ = WARNING: no frequency found!
>
> CLK_FREQ_HZ = WARNING: no frequency found!
> opb.OPB_Clk connected to sys_clk_s:
> CLK_FREQ_HZ = WARNING: no frequency found!
> plb2opb.PLB_Clk connected to sys_clk_s:
> CLK_FREQ_HZ = WARNING: no frequency found!
>
> plb2opb.OPB_Clk connected to sys_clk_s:
> CLK_FREQ_HZ = WARNING: no frequency found!
> RS232_Uart_1.OPB_Clk connected to sys_clk_s:
> CLK_FREQ_HZ = WARNING: no frequency found!
>
> Ethernet_MAC.OPB_Clk connected to sys_clk_s:
> CLK_FREQ_HZ = WARNING: no frequency found!
> SysACE_CompactFlash.OPB_Clk connected to sys_clk_s:
> CLK_FREQ_HZ = WARNING: no frequency found!
> DDR_256MB_32MX64_rank1_row13_col10_cl2_5.PLB_Clk connected to sys_clk_s:
> CLK_FREQ_HZ = WARNING: no frequency found!
>
> plb_bram_if_cntlr_1.plb_clk connected to sys_clk_s:
> CLK_FREQ_HZ = WARNING: no frequency found!
> plb_bram_if_cntlr_1_bram.BRAM_Clk_A connected to
> plb_bram_if_cntlr_1_port_BRAM_Clk:
> CLK_FREQ_HZ = WARNING: no frequency found!
> opb_intc_0.OPB_Clk connected to sys_clk_s:
> CLK_FREQ_HZ = WARNING: no frequency found!
> dcm_0.CLKIN connected to dcm_clk_s:
> CLK_FREQ_HZ = WARNING: no frequency found!
> dcm_0.CLK0 connected to sys_clk_s:
> CLK_FREQ_HZ = WARNING: no frequency found!
> CLK_INPORT = CLKIN
> CLK_FACTOR = 1
> dcm_0.CLK90 connected to clk_90_s:
> CLK_FREQ_HZ = WARNING: no frequency found!
> CLK_INPORT = CLKIN
> CLK_FACTOR = 1
>
> dcm_0.CLKFX connected to proc_clk_s:
> CLK_FREQ_HZ = WARNING: no frequency found!
> CLK_INPORT = CLKIN
> CLK_FACTOR = C_CLKFX_MULTIPLY / C_CLKFX_DIVIDE
> dcm_1.CLKIN connected to ddr_feedback_s:
> CLK_FREQ_HZ = WARNING: no frequency found!
> dcm_1.CLK0 connected to dcm_1_FB:
> CLK_FREQ_HZ = WARNING: no frequency found!
> CLK_INPORT = CLKIN
> CLK_FACTOR = 1
> dcm_1.CLK90 connected to ddr_clk_90_s:
> CLK_FREQ_HZ = WARNING: no frequency found!
> CLK_INPORT = CLKIN
> CLK_FACTOR = 1
> Clock Frequency: 300000000
> IP connected to bus: plb
> ***************************************************************************************************************
> ***************************************************************************************************************
>
> I copied <edk_project_path>/ppc_405_0/libsrc/device-tree/xilinx.dts to
> <linux_path>/arch/powerpc/boot/dts/virtex405-ml405.dts .
> the device tree file looks like this:
> ****************************************************************************************************
> ****************************************************************************************************
> /*
> * Device Tree Generator version: 1.1
> *
> * (C) Copyright 2007-2008 Xilinx, Inc.
> * (C) Copyright 2007-2008 Michal Simek
> *
> * Michal SIMEK <monstr at monstr.eu>
> *
> * This program is free software; you can redistribute it and/or
> * modify it under the terms of the GNU General Public License as
> * published by the Free Software Foundation; either version 2 of
> * the License, or (at your option) any later version.
> *
> * This program is distributed in the hope that it will be useful,
> * but WITHOUT ANY WARRANTY; without even the implied warranty of
> * MERCHANTABILITY or FITNESS FOR A PARTICULAR PURPOSE. See the
> * GNU General Public License for more details.
> *
> * You should have received a copy of the GNU General Public License
> * along with this program; if not, write to the Free Software
> * Foundation, Inc., 59 Temple Place, Suite 330, Boston,
> * MA 02111-1307 USA
> *
> * CAUTION: This file is automatically generated by libgen.
> * Version: Xilinx EDK 8.2.02 EDK_Im_Sp2.4
> *
> * XPS project directory: edk_300_100_linux_2-6
> */
>
> /dts-v1/;
> / {
> #address-cells = <1>;
> #size-cells = <1>;
> compatible = "xlnx,virtex405", "xlnx,virtex";
> model = "testing";
> DDR_256MB_32MX64_rank1_row13_col10_cl2_5: memory at 0 {
> device_type = "memory";
> reg = < 0x0 0x10000000 >;
> } ;
> chosen {
> bootargs = "console=ttyS0,9600 root=/dev/xsysace/disc0/part3 ip=on";
> linux,stdout-path = "/plb at 0/opb at 40000000/serial at 40600000";
> } ;
> cpus {
> #address-cells = <1>;
> #cpus = <0x1>;
> #size-cells = <0>;
> ppc405_0: cpu at 0 {
> clock-frequency = <300000000>;
> compatible = "PowerPC,405", "ibm,ppc405";
> d-cache-line-size = <0x20>;
> d-cache-size = <0x4000>;
> dcr-access-method = "native";
> dcr-controller ;
> device_type = "cpu";
> i-cache-line-size = <0x20>;
> i-cache-size = <0x4000>;
> model = "PowerPC,405";
> reg = <0>;
> timebase-frequency = <300000000>;
> xlnx,dcr-resync = <0x0>;
> xlnx,deterministic-mult = <0x0>;
> xlnx,disable-operand-forwarding = <0x1>;
> xlnx,mmu-enable = <0x1>;
> } ;
> } ;
> plb: plb at 0 {
> #address-cells = <1>;
> #size-cells = <1>;
> compatible = "xlnx,plb-v34-1.02.a", "simple-bus";
> ranges ;
> opb: opb at 40000000 {
> #address-cells = <1>;
> #size-cells = <1>;
> compatible = "xlnx,opb-v20-1.10.c", "simple-bus";
> ranges = < 0x40000000 0x40000000 0x40000000 >;
> Ethernet_MAC: ethernet at 40c00000 {
> compatible = "xlnx,opb-ethernet-1.04.a";
> device_type = "network";
> local-mac-address = [ 02 00 00 00 00 00 ];
> reg = < 0x40c00000 0x10000 >;
> xlnx,cam-bram-0-srl-1 = <0x1>;
> xlnx,cam-exist = <0x0>;
> xlnx,dev-blk-id = <0x1>;
> xlnx,dev-mir-enable = <0x1>;
> xlnx,dma-intr-coalesce = <0x1>;
> xlnx,dma-present = <0x1>;
> xlnx,err-count-exist = <0x1>;
> xlnx,family = "virtex2p";
> xlnx,fcs-insert-exist = <0x1>;
> xlnx,half-duplex-exist = <0x1>;
> xlnx,include-dev-pencoder = <0x1>;
> xlnx,ipif-rdfifo-depth = <0x8000>;
> xlnx,ipif-wrfifo-depth = <0x8000>;
> xlnx,jumbo-exist = <0x0>;
> xlnx,mac-fifo-bram-1-srl-0 = <0x0>;
> xlnx,mac-fifo-depth = <0x40>;
> xlnx,mii-exist = <0x1>;
> xlnx,miim-clkdvd = <0x1f>;
> xlnx,pad-insert-exist = <0x1>;
> xlnx,reset-present = <0x1>;
> xlnx,rx-dre-type = <0x0>;
> xlnx,rx-include-csum = <0x0>;
> xlnx,source-addr-insert-exist = <0x1>;
> xlnx,tx-dre-type = <0x0>;
> xlnx,tx-include-csum = <0x0>;
> } ;
> RS232_Uart_1: serial at 40600000 {
> clock-frequency = "";
> compatible = "xlnx,opb-uartlite-1.00.b";
> current-speed = <9600>;
> device_type = "serial";
> interrupt-parent = <&opb_intc_0>;
> interrupts = < 1 0 >;
> port-number = <0>;
> reg = < 0x40600000 0x10000 >;
> xlnx,baudrate = <0x9600>;
> xlnx,clk-freq = <0x5f5e100>;
> xlnx,data-bits = <0x8>;
> xlnx,odd-parity = <0x0>;
> xlnx,use-parity = <0x0>;
> } ;
> SysACE_CompactFlash: sysace at 41800000 {
> compatible = "xlnx,opb-sysace-1.00.c";
> interrupt-parent = <&opb_intc_0>;
> interrupts = < 0 2 >;
> reg = < 0x41800000 0x10000 >;
> xlnx,mem-width = <0x10>;
> } ;
> opb_intc_0: interrupt-controller at 41200000 {
> #interrupt-cells = <0x2>;
> compatible = "xlnx,opb-intc-1.00.c";
> interrupt-controller ;
> reg = < 0x41200000 0x10000 >;
> xlnx,num-intr-inputs = <0x2>;
> } ;
> } ;
> } ;
> } ;
> ******************************************************************************************************
> ******************************************************************************************************
>
> Then cp <linux_path>/arch/powerpc/configs/40x/virtex4_defconfig
> <linux_path>/.
>
> Then
> cd <linux_path>
> export ARCH=powerpc
> export CROSS_COMPILE=powerpc-405-linux-gnu-
> export
> PATH=${PATH}:$HOME/xupv2p/opt/crosstool/gcc-3.4.5-glibc-2.3.5/powerpc-405-linux-gnu/bin
> make menuconfig
> I disabled all the options and enabled only:
> -------------------------------------------------------------------------------------------------------------------------------------------------------------------------
> Processor support -> Processor Type AMCC 40x (!!! there is not ppc 40x)
> Platform Support -> Generic Xilinx Virtex board
> Kernel options -> Kernel support for ELF binaries
> Math emulation
> Default bootloader kernel arguments
> (console=ttyS0,9600) Initial kernel
> command string
> (simpleImage.virtex405-ml405)
> Additional default image types
> Device Drivers -> Character Devices -> Virtual Terminal
> Serial Devices
> -> [*] 8250/16550 and compatible serial
>
> [*] Console on 8250/16550 and compatible serial port
>
> (4) Maximum number of 8250/16550 serial ports
>
> (4) Number of 8250/16550 serial ports to register at runtime
>
> --------------------------------------------------------------------------------------------------------------------------------------------------------------------
>
> Then make clean && make dep && make zImage
> I obtained a binary zImage file (and not zImage.elf) !!!! and I obtained
> simpleImage.virtex405-ml405.elf in <linux_path>/arch/powerpc/boot .
>
> I used xmd to generated a system.ace from the bitstream and the elf.
> The report of xmd is:
> ******************************************************************************
> *****************************************************************************
> XMD% xmd -tcl genace.tcl -opt genace1.opt
> Xilinx Microprocessor Debug (XMD) Engine
> Xilinx EDK 8.2.02 Build EDK_Im_Sp2.4
> Copyright (c) 1995-2005 Xilinx, Inc. All rights reserved.
> Executing user script : genace.tcl
>
> #######################################################################
> XMD GenACE utility. Generate SystemACE File from bit/elf/data Files
> #######################################################################
> Using GenACE option file : genace1.opt
> GenACE Options:
> Board : xupv2p
> Jtag Devs : xc2vp30
> FPGA pos : 1
> JPROG : true
> HW File :
> /home/dhouib/xupv2p/edk_300_100_linux_2-6/implementation/system.bit
> ACE File : system3.ace
> nCPUs : 1
>
> Processor ppc_hw_1 Information
> Debug opt : -debugdevice devicenr 1 cpunr 1
> ELF files : simpleImage.virtex405-ml405-3.elf
> Start PC Address : 0x00400000
>
> ############################################################
> Converting Bitstream
> '/home/dhouib/xupv2p/edk_300_100_linux_2-6/implementation/system.bit' to
> SVF file
> '/home/dhouib/xupv2p/edk_300_100_linux_2-6/implementation/system.svf'
> Executing 'impact -batch bit2svf.scr'
>
> Copying
> /home/dhouib/xupv2p/edk_300_100_linux_2-6/implementation/system.svf File
> to system3.svf File
>
>
> ############################################################
> Converting ELF file 'simpleImage.virtex405-ml405-3.elf' to SVF file
> 'simpleImage.virtex405-ml405-3.svf'
> Target reset successfully
> section, .text: 0x00400000-0x00408ed4
> section, .data: 0x00409000-0x0040ac18
> section, __builtin_cmdline: 0x0040ac18-0x0040ae18
> section, .kernel:dtb: 0x0040ae18-0x0040be33
> section, .kernel:vmlinux.strip: 0x0040c000-0x004c3ae1
> section, .bss: 0x004c4000-0x004d0dd8
> Downloaded Program simpleImage.virtex405-ml405-3.elf
> Setting PC with program start addr = 0x00400000
> PC reset to 0x00400000, Clearing MSR Register
>
> Copying simpleImage.virtex405-ml405-3.svf File to system3.svf File
>
>
> ############################################################
> Writing Processor JTAG "continue" command to SVF file 'sw_suffix.svf'
> PC reset to 0x00400000, Clearing MSR Register
> Processor started. Type "stop" to stop processor
>
> ############################################################
> Converting SVF file 'system3.svf' to SystemACE file 'system3.ace'
> Executing 'impact -batch svf2ace.scr'
>
> SystemACE file 'system3.ace' created successfully
> ********************************************************************************************
> ********************************************************************************************
>
>
> I copied the system3.ace (3 because it was the third kernel that I tested
> :((( ) to the flash disk partition 1 (Type = FAT16, Size = 32Mo ).
> And I booted the kernel.
> I got fllowing message on the Terminal:
>
> *****************************************************************************************
> zImage starting: loaded at 0x00400000 (sp: 0x004c4efc)
> Allocating 0x1acdec bytes for kernel ...
> gunzipping (0x00000000 <- 0x0040c000:0x004c3ae1)...done 0x1951b8 bytes
>
> Linux/PowerPC load: console=ttyS0,9600 root=/dev/xsysace/disc0/part3 ip=on
> Finalizing device tree... flat tree at 0x40ae18
> *******************************************************************************************
>
> My Questions are:
> 1. Why he stops here?
> 2. Why I didn't obtained zImage.elf but simpleImage.virtex405-ml405.elf
> 3. Do I have to copy other files from my <edk_project_path> (xparameters.h
> , drivers ) to the <linux_path> ? (I copied only the xilinx.dts file)
>
> Thanks
> saadia
>
>
>
>
>
>
--
View this message in context: http://www.nabble.com/Linux-2.6-boot-failure-on-xup-virtex-II-ppc405-tp20252128p20269333.html
Sent from the linuxppc-embedded mailing list archive at Nabble.com.
More information about the Linuxppc-embedded
mailing list