Xilinx LLTEMAC driver issues
Magnus Hjorth
mh at omnisys.se
Mon Mar 31 22:10:51 EST 2008
Deactivating checksum offloading helped a lot! I still have some packet loss and not the best performance (TFTP transfer about 100 kbyte/s) but at least it works.
Thanks!
//Magnus
> -----Original Message-----
> From: rza1 [mailto:rza1 at so-logic.net]
> Sent: den 31 mars 2008 11:14
> To: Magnus Hjorth
> Cc: John Linn; git; linuxppc-embedded at ozlabs.org
> Subject: Re: Xilinx LLTEMAC driver issues
>
> Hi Magnus,
>
> 1.
> I am using nearly the same versions then you and got the same problems
> too ;-).
> I think there are some problems with the checksum offloading.
> Try to sniff the some packages (e.g. wireshark)...
> For me ICMP (ping) worked but udp and tcp not (because off a wrong
> checksum in the transport layer).
> A quick solution is to just deactivate checksum offloading.
>
> 2.
> I remember some problems with Virtex-4 presamples too.
> There where problems with the hard-temac wrapper. You had to use 1.00.a
> and not b version.
> But I don't have these problems with the EDK 9.2sp2/ISE9.2sp3 anymore.
>
> all the best,
> Robert
>
> Magnus Hjorth wrote:
> > Hi John,
> >
> > Thanks for the very fast reply! Right now I'm not at work so I don't
> > have the board or EDK here to test anything.
> >
> > I'm using checksum offload, but I don't know if DRE is enabled or not. I
> > can't recall seeing any setting to enable/disable DRE..
> >
> > A few things that crossed my mind:
> >
> > Last year I did a design with EDK 8.2, back then there was an issue with
> > the ML403 boards having an old revision of the FPGA which wasn't
> > compatible with some versions of the IP core. There are no such version
> > issues with the xps_ll_temac?
> >
> > I don't think that I had phy-addr set in the DTS file. Will test that on
> > Monday.
> >
> > Best regards,
> > Magnus
> >
> >
> > On Sat, 2008-03-29 at 07:58 -0600, John Linn wrote:
> >
> >> Hi Magnus,
> >>
> >> Sorry to hear you're having problems with it.
> >>
> >> I am doing testing on an ML405 which is the same board but with a bigger
> FPGA, but with ppc arch and I don't see this issue. I have done limited testing
> with powerpc arch and the LL TEMAC, but I didn't see this issue there either.
> Powerpc arch is definitely less mature in my experience than the ppc arch. I'll
> do a quick test with my powerpc arch and make sure again I'm not seeing it.
> >>
> >> My kernel is from the Xilinx Git tree, but there have been a number of
> changes we have pushed out so I don't know how long ago you pulled from the Git
> tree.
> >>
> >> My EDK project is 10.1 so it's a little newer. I am using LL TEMAC 1.01a so
> it's a little newer. I reviewed the change log for the LL TEMAC and don't see
> any big problems that were fixed in the newer versions, more new features. I'll
> check with some others here to see if I missed something there.
> >>
> >> I am using DMA also, but no DRE or checksum offload. You didn't say anything
> about those. I'm going to insert my mhs file that describes my system to let you
> compare your system configuration. It's not clear to me yet if you have a h/w or
> s/w problem.
> >>
> >> I'll also insert some of my device tree with the LL TEMAC so you can compare
> (ignore 16550 stuff as we are still working on that).
> >>
> >> Since you can't ping reliably I would probably focus on that since it's
> simpler than the other issues you're seeing.
> >>
> >> Thanks,
> >> John
> >>
> >>
> >>
> >> #
> ##############################################################################
> >> # Created by Base System Builder Wizard for Xilinx EDK 10.1.1 Build
> EDK_K_SP1.1
> >> # Thu Feb 14 14:11:12 2008
> >> # Target Board: Xilinx Virtex 4 ML405 Evaluation Platform Rev 1
> >> # Family: virtex4
> >> # Device: xc4vfx20
> >> # Package: ff672
> >> # Speed Grade: -10
> >> # Processor: ppc405_0
> >> # Processor clock frequency: 300.00 MHz
> >> # Bus clock frequency: 100.00 MHz
> >> # On Chip Memory : 8 KB
> >> # Total Off Chip Memory : 128 MB
> >> # - DDR_SDRAM = 128 MB
> >> #
> ##############################################################################
> >> PARAMETER VERSION = 2.1.0
> >>
> >>
> >> PORT fpga_0_RS232_Uart_sin_pin = fpga_0_RS232_Uart_sin, DIR = I
> >> PORT fpga_0_RS232_Uart_sout_pin = fpga_0_RS232_Uart_sout, DIR = O
> >> PORT fpga_0_LEDs_4Bit_GPIO_IO_pin = fpga_0_LEDs_4Bit_GPIO_IO, DIR = IO, VEC
> = [0:3]
> >> PORT fpga_0_IIC_EEPROM_Scl_pin = fpga_0_IIC_EEPROM_Scl, DIR = IO
> >> PORT fpga_0_IIC_EEPROM_Sda_pin = fpga_0_IIC_EEPROM_Sda, DIR = IO
> >> PORT fpga_0_SysACE_CompactFlash_SysACE_CLK_pin =
> fpga_0_SysACE_CompactFlash_SysACE_CLK, DIR = I
> >> PORT fpga_0_SysACE_CompactFlash_SysACE_MPA_pin =
> fpga_0_SysACE_CompactFlash_SysACE_MPA, DIR = O, VEC = [6:1]
> >> PORT fpga_0_SysACE_CompactFlash_SysACE_MPD_pin =
> fpga_0_SysACE_CompactFlash_SysACE_MPD, DIR = IO, VEC = [15:0]
> >> PORT fpga_0_SysACE_CompactFlash_SysACE_CEN_pin =
> fpga_0_SysACE_CompactFlash_SysACE_CEN, DIR = O
> >> PORT fpga_0_SysACE_CompactFlash_SysACE_OEN_pin =
> fpga_0_SysACE_CompactFlash_SysACE_OEN, DIR = O
> >> PORT fpga_0_SysACE_CompactFlash_SysACE_WEN_pin =
> fpga_0_SysACE_CompactFlash_SysACE_WEN, DIR = O
> >> PORT fpga_0_SysACE_CompactFlash_SysACE_MPIRQ_pin =
> fpga_0_SysACE_CompactFlash_SysACE_MPIRQ, DIR = I
> >> PORT fpga_0_DDR_SDRAM_DDR_Clk_pin = fpga_0_DDR_SDRAM_DDR_Clk, DIR = O
> >> PORT fpga_0_DDR_SDRAM_DDR_Clk_n_pin = fpga_0_DDR_SDRAM_DDR_Clk_n, DIR = O
> >> PORT fpga_0_DDR_SDRAM_DDR_Addr_pin = fpga_0_DDR_SDRAM_DDR_Addr, DIR = O, VEC
> = [12:0]
> >> PORT fpga_0_DDR_SDRAM_DDR_BankAddr_pin = fpga_0_DDR_SDRAM_DDR_BankAddr, DIR
> = O, VEC = [1:0]
> >> PORT fpga_0_DDR_SDRAM_DDR_CAS_n_pin = fpga_0_DDR_SDRAM_DDR_CAS_n, DIR = O
> >> PORT fpga_0_DDR_SDRAM_DDR_CE_pin = fpga_0_DDR_SDRAM_DDR_CE, DIR = O
> >> PORT fpga_0_DDR_SDRAM_DDR_CS_n_pin = fpga_0_DDR_SDRAM_DDR_CS_n, DIR = O
> >> PORT fpga_0_DDR_SDRAM_DDR_RAS_n_pin = fpga_0_DDR_SDRAM_DDR_RAS_n, DIR = O
> >> PORT fpga_0_DDR_SDRAM_DDR_WE_n_pin = fpga_0_DDR_SDRAM_DDR_WE_n, DIR = O
> >> PORT fpga_0_DDR_SDRAM_DDR_DM_pin = fpga_0_DDR_SDRAM_DDR_DM, DIR = O, VEC =
> [3:0]
> >> PORT fpga_0_DDR_SDRAM_DDR_DQS = fpga_0_DDR_SDRAM_DDR_DQS, DIR = IO, VEC =
> [3:0]
> >> PORT fpga_0_DDR_SDRAM_DDR_DQ = fpga_0_DDR_SDRAM_DDR_DQ, DIR = IO, VEC =
> [31:0]
> >> PORT fpga_0_TriMode_MAC_GMII_GMII_TXD_0_pin =
> fpga_0_TriMode_MAC_GMII_GMII_TXD_0, DIR = O, VEC = [7:0]
> >> PORT fpga_0_TriMode_MAC_GMII_GMII_TX_EN_0_pin =
> fpga_0_TriMode_MAC_GMII_GMII_TX_EN_0, DIR = O
> >> PORT fpga_0_TriMode_MAC_GMII_GMII_TX_ER_0_pin =
> fpga_0_TriMode_MAC_GMII_GMII_TX_ER_0, DIR = O
> >> PORT fpga_0_TriMode_MAC_GMII_GMII_TX_CLK_0_pin =
> fpga_0_TriMode_MAC_GMII_GMII_TX_CLK_0, DIR = O
> >> PORT fpga_0_TriMode_MAC_GMII_GMII_RXD_0_pin =
> fpga_0_TriMode_MAC_GMII_GMII_RXD_0, DIR = I, VEC = [7:0]
> >> PORT fpga_0_TriMode_MAC_GMII_GMII_RX_DV_0_pin =
> fpga_0_TriMode_MAC_GMII_GMII_RX_DV_0, DIR = I
> >> PORT fpga_0_TriMode_MAC_GMII_GMII_RX_ER_0_pin =
> fpga_0_TriMode_MAC_GMII_GMII_RX_ER_0, DIR = I
> >> PORT fpga_0_TriMode_MAC_GMII_GMII_RX_CLK_0_pin =
> fpga_0_TriMode_MAC_GMII_GMII_RX_CLK_0, DIR = I
> >> PORT fpga_0_TriMode_MAC_GMII_MII_TX_CLK_0_pin =
> fpga_0_TriMode_MAC_GMII_MII_TX_CLK_0, DIR = I
> >> PORT fpga_0_TriMode_MAC_GMII_MDIO_0_pin = fpga_0_TriMode_MAC_GMII_MDIO_0,
> DIR = IO
> >> PORT fpga_0_TriMode_MAC_GMII_MDC_0_pin = fpga_0_TriMode_MAC_GMII_MDC_0, DIR
> = O
> >> PORT fpga_0_TriMode_MAC_GMII_TemacPhy_RST_n_pin =
> fpga_0_TriMode_MAC_GMII_TemacPhy_RST_n, DIR = O
> >> PORT sys_clk_pin = dcm_clk_s, DIR = I, SIGIS = CLK, CLK_FREQ = 100000000
> >> PORT sys_rst_pin = sys_rst_s, DIR = I, RST_POLARITY = 0, SIGIS = RST
> >>
> >>
> >> BEGIN ppc405_virtex4
> >> PARAMETER INSTANCE = ppc405_0
> >> PARAMETER HW_VER = 2.01.a
> >> PARAMETER C_FASTEST_PLB_CLOCK = DPLB1
> >> PARAMETER C_IDCR_BASEADDR = 0b0100000000
> >> PARAMETER C_IDCR_HIGHADDR = 0b0111111111
> >> BUS_INTERFACE JTAGPPC = jtagppc_0_0
> >> BUS_INTERFACE IPLB0 = plb
> >> BUS_INTERFACE DPLB0 = plb
> >> BUS_INTERFACE IPLB1 = ppc405_0_iplb1
> >> BUS_INTERFACE DPLB1 = ppc405_0_dplb1
> >> BUS_INTERFACE RESETPPC = ppc_reset_bus
> >> PORT CPMC405CLOCK = proc_clk_s
> >> PORT EICC405EXTINPUTIRQ = EICC405EXTINPUTIRQ
> >> END
> >>
> >> BEGIN jtagppc_cntlr
> >> PARAMETER INSTANCE = jtagppc_0
> >> PARAMETER HW_VER = 2.01.a
> >> BUS_INTERFACE JTAGPPC0 = jtagppc_0_0
> >> END
> >>
> >> BEGIN plb_v46
> >> PARAMETER INSTANCE = plb
> >> PARAMETER C_DCR_INTFCE = 0
> >> PARAMETER C_NUM_CLK_PLB2OPB_REARB = 100
> >> PARAMETER HW_VER = 1.02.a
> >> PORT PLB_Clk = sys_clk_s
> >> PORT SYS_Rst = sys_bus_reset
> >> END
> >>
> >> BEGIN xps_bram_if_cntlr
> >> PARAMETER INSTANCE = xps_bram_if_cntlr_1
> >> PARAMETER HW_VER = 1.00.a
> >> PARAMETER C_SPLB_NATIVE_DWIDTH = 64
> >> PARAMETER C_BASEADDR = 0xffffe000
> >> PARAMETER C_HIGHADDR = 0xffffffff
> >> BUS_INTERFACE SPLB = plb
> >> BUS_INTERFACE PORTA = xps_bram_if_cntlr_1_port
> >> END
> >>
> >> BEGIN bram_block
> >> PARAMETER INSTANCE = plb_bram_if_cntlr_1_bram
> >> PARAMETER HW_VER = 1.00.a
> >> BUS_INTERFACE PORTA = xps_bram_if_cntlr_1_port
> >> END
> >>
> >> BEGIN xps_uart16550
> >> PARAMETER INSTANCE = RS232_Uart
> >> PARAMETER HW_VER = 2.00.a
> >> PARAMETER C_IS_A_16550 = 1
> >> PARAMETER C_BASEADDR = 0x83e00000
> >> PARAMETER C_HIGHADDR = 0x83e0ffff
> >> BUS_INTERFACE SPLB = plb
> >> PORT sin = fpga_0_RS232_Uart_sin
> >> PORT sout = fpga_0_RS232_Uart_sout
> >> PORT IP2INTC_Irpt = RS232_Uart_IP2INTC_Irpt
> >> END
> >>
> >> BEGIN xps_gpio
> >> PARAMETER INSTANCE = LEDs_4Bit
> >> PARAMETER HW_VER = 1.00.a
> >> PARAMETER C_INTERRUPT_PRESENT = 1
> >> PARAMETER C_GPIO_WIDTH = 4
> >> PARAMETER C_IS_DUAL = 0
> >> PARAMETER C_IS_BIDIR = 1
> >> PARAMETER C_ALL_INPUTS = 0
> >> PARAMETER C_BASEADDR = 0x81400000
> >> PARAMETER C_HIGHADDR = 0x8140ffff
> >> BUS_INTERFACE SPLB = plb
> >> PORT GPIO_IO = fpga_0_LEDs_4Bit_GPIO_IO
> >> PORT IP2INTC_Irpt = LEDs_4Bit_IP2INTC_Irpt
> >> END
> >>
> >> BEGIN xps_iic
> >> PARAMETER INSTANCE = IIC_EEPROM
> >> PARAMETER HW_VER = 2.00.a
> >> PARAMETER C_CLK_FREQ = 100000000
> >> PARAMETER C_IIC_FREQ = 100000
> >> PARAMETER C_TEN_BIT_ADR = 0
> >> PARAMETER C_BASEADDR = 0x81600000
> >> PARAMETER C_HIGHADDR = 0x8160ffff
> >> BUS_INTERFACE SPLB = plb
> >> PORT Scl = fpga_0_IIC_EEPROM_Scl
> >> PORT Sda = fpga_0_IIC_EEPROM_Sda
> >> PORT IIC2INTC_Irpt = IIC_EEPROM_IIC2INTC_Irpt
> >> END
> >>
> >> BEGIN xps_sysace
> >> PARAMETER INSTANCE = SysACE_CompactFlash
> >> PARAMETER HW_VER = 1.00.a
> >> PARAMETER C_MEM_WIDTH = 16
> >> PARAMETER C_BASEADDR = 0x83600000
> >> PARAMETER C_HIGHADDR = 0x8360ffff
> >> BUS_INTERFACE SPLB = plb
> >> PORT SysACE_CLK = fpga_0_SysACE_CompactFlash_SysACE_CLK
> >> PORT SysACE_MPA = fpga_0_SysACE_CompactFlash_SysACE_MPA_split
> >> PORT SysACE_MPD = fpga_0_SysACE_CompactFlash_SysACE_MPD
> >> PORT SysACE_CEN = fpga_0_SysACE_CompactFlash_SysACE_CEN
> >> PORT SysACE_OEN = fpga_0_SysACE_CompactFlash_SysACE_OEN
> >> PORT SysACE_WEN = fpga_0_SysACE_CompactFlash_SysACE_WEN
> >> PORT SysACE_MPIRQ = fpga_0_SysACE_CompactFlash_SysACE_MPIRQ
> >> PORT SysACE_IRQ = SysACE_CompactFlash_SysACE_IRQ
> >> END
> >>
> >> BEGIN mpmc
> >> PARAMETER INSTANCE = DDR_SDRAM
> >> PARAMETER HW_VER = 4.00.a
> >> PARAMETER C_NUM_PORTS = 3
> >> PARAMETER C_MEM_PARTNO = HYB25D512160BE-5
> >> PARAMETER C_MEM_DATA_WIDTH = 32
> >> PARAMETER C_MEM_DQS_WIDTH = 4
> >> PARAMETER C_MEM_DM_WIDTH = 4
> >> PARAMETER C_MEM_TYPE = DDR
> >> PARAMETER C_NUM_IDELAYCTRL = 2
> >> PARAMETER C_IDELAYCTRL_LOC = IDELAYCTRL_X0Y3-IDELAYCTRL_X0Y2
> >> PARAMETER C_PIM0_BASETYPE = 2
> >> PARAMETER C_PIM1_BASETYPE = 2
> >> PARAMETER C_PIM2_BASETYPE = 3
> >> PARAMETER C_MPMC_CLK0_PERIOD_PS = 10000
> >> PARAMETER C_SDMA2_PI2LL_CLK_RATIO = 1
> >> PARAMETER C_MPMC_BASEADDR = 0x00000000
> >> PARAMETER C_MPMC_HIGHADDR = 0x07ffffff
> >> PARAMETER C_SDMA_CTRL_BASEADDR = 0x84600000
> >> PARAMETER C_SDMA_CTRL_HIGHADDR = 0x8460ffff
> >> BUS_INTERFACE SPLB0 = ppc405_0_iplb1
> >> BUS_INTERFACE SPLB1 = ppc405_0_dplb1
> >> BUS_INTERFACE SDMA_LL2 = TriMode_MAC_GMII_LLINK0
> >> BUS_INTERFACE SDMA_CTRL2 = plb
> >> PORT DDR_Addr = fpga_0_DDR_SDRAM_DDR_Addr
> >> PORT DDR_BankAddr = fpga_0_DDR_SDRAM_DDR_BankAddr
> >> PORT DDR_CAS_n = fpga_0_DDR_SDRAM_DDR_CAS_n
> >> PORT DDR_CE = fpga_0_DDR_SDRAM_DDR_CE
> >> PORT DDR_CS_n = fpga_0_DDR_SDRAM_DDR_CS_n
> >> PORT DDR_RAS_n = fpga_0_DDR_SDRAM_DDR_RAS_n
> >> PORT DDR_WE_n = fpga_0_DDR_SDRAM_DDR_WE_n
> >> PORT DDR_DM = fpga_0_DDR_SDRAM_DDR_DM
> >> PORT DDR_DQS = fpga_0_DDR_SDRAM_DDR_DQS
> >> PORT DDR_DQ = fpga_0_DDR_SDRAM_DDR_DQ
> >> PORT DDR_Clk = fpga_0_DDR_SDRAM_DDR_Clk
> >> PORT DDR_Clk_n = fpga_0_DDR_SDRAM_DDR_Clk_n
> >> PORT MPMC_Clk0 = sys_clk_s
> >> PORT MPMC_Clk90 = DDR_SDRAM_mpmc_clk_90_s
> >> PORT SDMA2_Clk = sys_clk_s
> >> PORT MPMC_Clk_200MHz = clk_200mhz_s
> >> PORT MPMC_Rst = sys_periph_reset
> >> PORT SDMA2_Rx_IntOut = DDR_SDRAM_SDMA2_Rx_IntOut
> >> PORT SDMA2_Tx_IntOut = DDR_SDRAM_SDMA2_Tx_IntOut
> >> END
> >>
> >> BEGIN xps_ll_temac
> >> PARAMETER INSTANCE = TriMode_MAC_GMII
> >> PARAMETER HW_VER = 1.01.a
> >> PARAMETER C_SPLB_CLK_PERIOD_PS = 10000
> >> PARAMETER C_PHY_TYPE = 1
> >> PARAMETER C_NUM_IDELAYCTRL = 4
> >> PARAMETER C_IDELAYCTRL_LOC = IDELAYCTRL_X1Y1-IDELAYCTRL_X1Y3-
> IDELAYCTRL_X2Y2-IDELAYCTRL_X2Y3
> >> PARAMETER C_TEMAC_TYPE = 1
> >> PARAMETER C_BUS2CORE_CLK_RATIO = 1
> >> PARAMETER C_BASEADDR = 0x81c00000
> >> PARAMETER C_HIGHADDR = 0x81c0ffff
> >> BUS_INTERFACE SPLB = plb
> >> BUS_INTERFACE LLINK0 = TriMode_MAC_GMII_LLINK0
> >> PORT GMII_TXD_0 = fpga_0_TriMode_MAC_GMII_GMII_TXD_0
> >> PORT GMII_TX_EN_0 = fpga_0_TriMode_MAC_GMII_GMII_TX_EN_0
> >> PORT GMII_TX_ER_0 = fpga_0_TriMode_MAC_GMII_GMII_TX_ER_0
> >> PORT GMII_TX_CLK_0 = fpga_0_TriMode_MAC_GMII_GMII_TX_CLK_0
> >> PORT GMII_RXD_0 = fpga_0_TriMode_MAC_GMII_GMII_RXD_0
> >> PORT GMII_RX_DV_0 = fpga_0_TriMode_MAC_GMII_GMII_RX_DV_0
> >> PORT GMII_RX_ER_0 = fpga_0_TriMode_MAC_GMII_GMII_RX_ER_0
> >> PORT GMII_RX_CLK_0 = fpga_0_TriMode_MAC_GMII_GMII_RX_CLK_0
> >> PORT MII_TX_CLK_0 = fpga_0_TriMode_MAC_GMII_MII_TX_CLK_0
> >> PORT MDIO_0 = fpga_0_TriMode_MAC_GMII_MDIO_0
> >> PORT MDC_0 = fpga_0_TriMode_MAC_GMII_MDC_0
> >> PORT TemacPhy_RST_n = fpga_0_TriMode_MAC_GMII_TemacPhy_RST_n
> >> PORT GTX_CLK_0 = temac_clk_s
> >> PORT REFCLK = clk_200mhz_s
> >> PORT LlinkTemac0_CLK = sys_clk_s
> >> PORT TemacIntc0_Irpt = TriMode_MAC_GMII_TemacIntc0_Irpt
> >> END
> >>
> >> BEGIN util_bus_split
> >> PARAMETER INSTANCE = SysACE_CompactFlash_util_bus_split_0
> >> PARAMETER HW_VER = 1.00.a
> >> PARAMETER C_SIZE_IN = 7
> >> PARAMETER C_LEFT_POS = 0
> >> PARAMETER C_SPLIT = 6
> >> PORT Sig = fpga_0_SysACE_CompactFlash_SysACE_MPA_split
> >> PORT Out1 = fpga_0_SysACE_CompactFlash_SysACE_MPA
> >> END
> >>
> >> BEGIN plb_v46
> >> PARAMETER INSTANCE = ppc405_0_iplb1
> >> PARAMETER HW_VER = 1.02.a
> >> PORT PLB_Clk = sys_clk_s
> >> PORT SYS_Rst = sys_bus_reset
> >> END
> >>
> >> BEGIN plb_v46
> >> PARAMETER INSTANCE = ppc405_0_dplb1
> >> PARAMETER HW_VER = 1.02.a
> >> PORT PLB_Clk = sys_clk_s
> >> PORT SYS_Rst = sys_bus_reset
> >> END
> >>
> >> BEGIN clock_generator
> >> PARAMETER INSTANCE = clock_generator_0
> >> PARAMETER HW_VER = 2.00.a
> >> PARAMETER C_EXT_RESET_HIGH = 1
> >> PARAMETER C_CLKIN_FREQ = 100000000
> >> PARAMETER C_CLKOUT0_FREQ = 100000000
> >> PARAMETER C_CLKOUT0_BUF = TRUE
> >> PARAMETER C_CLKOUT0_PHASE = 0
> >> PARAMETER C_CLKOUT0_GROUP = DCM0
> >> PARAMETER C_CLKOUT1_FREQ = 100000000
> >> PARAMETER C_CLKOUT1_BUF = TRUE
> >> PARAMETER C_CLKOUT1_PHASE = 90
> >> PARAMETER C_CLKOUT1_GROUP = DCM0
> >> PARAMETER C_CLKOUT2_FREQ = 300000000
> >> PARAMETER C_CLKOUT2_BUF = TRUE
> >> PARAMETER C_CLKOUT2_PHASE = 0
> >> PARAMETER C_CLKOUT2_GROUP = DCM0
> >> PARAMETER C_CLKOUT3_FREQ = 200000000
> >> PARAMETER C_CLKOUT3_BUF = TRUE
> >> PARAMETER C_CLKOUT3_PHASE = 0
> >> PARAMETER C_CLKOUT3_GROUP = NONE
> >> PARAMETER C_CLKOUT4_FREQ = 125000000
> >> PARAMETER C_CLKOUT4_BUF = TRUE
> >> PARAMETER C_CLKOUT4_PHASE = 0
> >> PARAMETER C_CLKOUT4_GROUP = NONE
> >> PORT CLKOUT0 = sys_clk_s
> >> PORT CLKOUT1 = DDR_SDRAM_mpmc_clk_90_s
> >> PORT CLKOUT2 = proc_clk_s
> >> PORT CLKOUT3 = clk_200mhz_s
> >> PORT CLKOUT4 = temac_clk_s
> >> PORT CLKIN = dcm_clk_s
> >> PORT LOCKED = Dcm_all_locked
> >> PORT RST = net_gnd
> >> END
> >>
> >> BEGIN proc_sys_reset
> >> PARAMETER INSTANCE = proc_sys_reset_0
> >> PARAMETER HW_VER = 2.00.a
> >> PARAMETER C_EXT_RESET_HIGH = 0
> >> BUS_INTERFACE RESETPPC0 = ppc_reset_bus
> >> PORT Slowest_sync_clk = sys_clk_s
> >> PORT Dcm_locked = Dcm_all_locked
> >> PORT Ext_Reset_In = sys_rst_s
> >> PORT Bus_Struct_Reset = sys_bus_reset
> >> PORT Peripheral_Reset = sys_periph_reset
> >> END
> >>
> >> BEGIN xps_intc
> >> PARAMETER INSTANCE = xps_intc_0
> >> PARAMETER HW_VER = 1.00.a
> >> PARAMETER C_BASEADDR = 0x81800000
> >> PARAMETER C_HIGHADDR = 0x8180ffff
> >> BUS_INTERFACE SPLB = plb
> >> PORT Irq = EICC405EXTINPUTIRQ
> >> PORT Intr = RS232_Uart_IP2INTC_Irpt & LEDs_4Bit_IP2INTC_Irpt &
> IIC_EEPROM_IIC2INTC_Irpt & SysACE_CompactFlash_SysACE_IRQ &
> TriMode_MAC_GMII_TemacIntc0_Irpt & DDR_SDRAM_SDMA2_Rx_IntOut &
> DDR_SDRAM_SDMA2_Tx_IntOut
> >> END
> >>
> >>
> >>
> >> #address-cells = <1>;
> >> #size-cells = <1>;
> >> compatible = "xlnx,virtex";
> >> model = "testing";
> >> DDR_SDRAM: memory at 0 {
> >> device_type = "memory";
> >> reg = < 0 8000000 >;
> >> } ;
> >> chosen {
> >> bootargs = "console=ttyS0,9600 ip=on
> nfsroot=172.16.40.76:/v2pclients/jhl26,tcp";
> >> linux,stdout-path = "/plb at 0/serial at 83e00000";
> >> } ;
> >> cpus {
> >> #address-cells = <1>;
> >> #cpus = <1>;
> >> #size-cells = <0>;
> >> ppc405_0: cpu at 0 {
> >> clock-frequency = <11e1a300>;
> >> compatible = "PowerPC,405", "ibm,ppc405";
> >> d-cache-line-size = <20>;
> >> d-cache-size = <4000>;
> >> device_type = "cpu";
> >> i-cache-line-size = <20>;
> >> i-cache-size = <4000>;
> >> model = "PowerPC,405";
> >> reg = <0>;
> >> timebase-frequency = <11e1a300>;
> >> xlnx,apu-control = <de00>;
> >> xlnx,apu-udi-1 = <a18983>;
> >> xlnx,apu-udi-2 = <a38983>;
> >> xlnx,apu-udi-3 = <a589c3>;
> >> xlnx,apu-udi-4 = <a789c3>;
> >> xlnx,apu-udi-5 = <a98c03>;
> >> xlnx,apu-udi-6 = <ab8c03>;
> >> xlnx,apu-udi-7 = <ad8c43>;
> >> xlnx,apu-udi-8 = <af8c43>;
> >> xlnx,deterministic-mult = <0>;
> >> xlnx,disable-operand-forwarding = <1>;
> >> xlnx,fastest-plb-clock = "DPLB0";
> >> xlnx,generate-plb-timespecs = <1>;
> >> xlnx,mmu-enable = <1>;
> >> xlnx,pvr-high = <0>;
> >> xlnx,pvr-low = <0>;
> >> } ;
> >> } ;
> >> plb: plb at 0 {
> >> #address-cells = <1>;
> >> #size-cells = <1>;
> >> compatible = "xlnx,plb-v46-1.02.a";
> >> ranges ;
> >> IIC_EEPROM: i2c at 81600000 {
> >> compatible = "xlnx,xps-iic-2.00.a";
> >> interrupt-parent = <&xps_intc_0>;
> >> interrupts = < 4 2 >;
> >> reg = < 81600000 10000 >;
> >> xlnx,clk-freq = <5f5e100>;
> >> xlnx,family = "virtex4";
> >> xlnx,gpo-width = <1>;
> >> xlnx,iic-freq = <186a0>;
> >> xlnx,scl-inertial-delay = <0>;
> >> xlnx,sda-inertial-delay = <0>;
> >> xlnx,ten-bit-adr = <0>;
> >> } ;
> >> LEDs_4Bit: gpio at 81400000 {
> >> compatible = "xlnx,xps-gpio-1.00.a";
> >> interrupt-parent = <&xps_intc_0>;
> >> interrupts = < 5 2 >;
> >> reg = < 81400000 10000 >;
> >> xlnx,all-inputs = <0>;
> >> xlnx,all-inputs-2 = <0>;
> >> xlnx,dout-default = <0>;
> >> xlnx,dout-default-2 = <0>;
> >> xlnx,family = "virtex4";
> >> xlnx,gpio-width = <4>;
> >> xlnx,interrupt-present = <1>;
> >> xlnx,is-bidir = <1>;
> >> xlnx,is-bidir-2 = <1>;
> >> xlnx,is-dual = <0>;
> >> xlnx,tri-default = <ffffffff>;
> >> xlnx,tri-default-2 = <ffffffff>;
> >> } ;
> >> RS232_Uart: serial at 83e00000 {
> >> compatible = "xlnx,xps-uart16550-2.00.a";
> >> // compatible = "ns16550";
> >> device_type = "serial";
> >> interrupt-parent = <&xps_intc_0>;
> >> interrupts = < 6 2 >;
> >> reg = < 83e00000 10000 >;
> >> current-speed = <d#9600>;
> >> clock-frequency = <d#100000000>; /* added
> by jhl */
> >> reg-shift = <2>;
> >> xlnx,family = "virtex4";
> >> xlnx,has-external-rclk = <0>;
> >> xlnx,has-external-xin = <0>;
> >> xlnx,is-a-16550 = <1>;
> >> } ;
> >> SysACE_CompactFlash: sysace at 83600000 {
> >> compatible = "xlnx,xps-sysace-1.00.a";
> >> interrupt-parent = <&xps_intc_0>;
> >> interrupts = < 3 2 >;
> >> reg = < 83600000 10000 >;
> >> xlnx,family = "virtex4";
> >> xlnx,mem-width = <10>;
> >> } ;
> >> TriMode_MAC_GMII: xps-ll-temac at 81c00000 {
> >> #address-cells = <1>;
> >> #size-cells = <1>;
> >> compatible = "xlnx,compound";
> >> ethernet at 81c00000 {
> >> compatible = "xlnx,xps-ll-temac-
> 1.01.a";
> >> device_type = "network";
> >> interrupt-parent =
> <&xps_intc_0>;
> >> interrupts = < 2 2 >;
> >> llink-connected = <&PIM2>;
> >> local-mac-address = [ 02 00 00
> 00 00 01 ];
> >> reg = < 81c00000 40 >;
> >> xlnx,bus2core-clk-ratio = <1>;
> >> xlnx,phy-type = <1>;
> >> xlnx,phyaddr = <1>;
> >> xlnx,rxcsum = <0>;
> >> xlnx,rxfifo = <1000>;
> >> xlnx,temac-type = <1>;
> >> xlnx,txcsum = <0>;
> >> xlnx,txfifo = <1000>;
> >> } ;
> >> } ;
> >> mpmc at 0 {
> >> #address-cells = <1>;
> >> #size-cells = <1>;
> >> compatible = "xlnx,mpmc-4.00.a";
> >> PIM2: sdma at 84600100 {
> >> compatible = "xlnx,ll-dma-
> 1.00.a";
> >> interrupt-parent =
> <&xps_intc_0>;
> >> interrupts = < 1 2 0 2 >;
> >> reg = < 84600100 80 >;
> >> } ;
> >> } ;
> >> xps_bram_if_cntlr_1: xps-bram-if-cntlr at ffffe000 {
> >> compatible = "xlnx,xps-bram-if-cntlr-
> 1.00.a";
> >> reg = < ffffe000 2000 >;
> >> xlnx,family = "virtex4";
> >> } ;
> >> xps_intc_0: interrupt-controller at 81800000 {
> >> #interrupt-cells = <2>;
> >> compatible = "xlnx,xps-intc-1.00.a";
> >> interrupt-controller ;
> >> reg = < 81800000 10000 >;
> >> xlnx,num-intr-inputs = <7>;
> >> } ;
> >> } ;
> >> ppc405_0_dplb1: plb at 1 {
> >> #address-cells = <1>;
> >> #size-cells = <1>;
> >> compatible = "xlnx,plb-v46-1.02.a";
> >> ranges ;
> >> } ;
> >> } ;
> >>
> >>
> >>
> >> -----Original Message-----
> >> From: Magnus Hjorth [mailto:mh at omnisys.se]
> >> Sent: Saturday, March 29, 2008 6:54 AM
> >> To: git
> >> Cc: linuxppc-embedded at ozlabs.org
> >> Subject: Xilinx LLTEMAC driver issues
> >>
> >> Hi,
> >>
> >> I'm having some networking troubles with the Xilinx LLTEMAC driver from the
> >> Xilinx Linux git tree (powerpc arch) on an ML403 board. EDK9.2SP2,
> >> xps_ll_temac v1.00.b
> >>
> >> The weird thing is, that it sort of half works. It successfully makes a DHCP
> >> request and gets its IP address. I tried setting up a tftpd server, and I can
> >> see UDP requests coming in but the response doesn't seem to come out. I also
> >> tried running a TCP server on the board, and it can see and accept incoming
> >> connections but after that no data seems to get through. I can ping out and
> >> get around 40% packet loss.
> >>
> >> Looking at /proc/interrupts, I can see both TxDma interrupts and RxDma
> >> interrupts. No eth0 interrupts but that seems to be OK judging by the driver
> >> source comments. Ifconfig shows no collistions, no dropped packets, no
> errors,
> >> so the system seems to think that everything is OK.
> >>
> >> Clues anyone? I'm starting to run out of ideas...
> >>
> >> Best regards,
> >> Magnus
> >>
> >>
> >> --
> >>
> >> Magnus Hjorth, M.Sc.
> >> Omnisys Instruments AB
> >> Gruvgatan 8
> >> SE-421 30 Västra Frölunda, SWEDEN
> >> Phone: +46 31 734 34 09
> >> Fax: +46 31 734 34 29
> >> http://www.omnisys.se
> >>
> >
> > _______________________________________________
> > Linuxppc-embedded mailing list
> > Linuxppc-embedded at ozlabs.org
> > https://ozlabs.org/mailman/listinfo/linuxppc-embedded
More information about the Linuxppc-embedded
mailing list