Try to Disable PPC Interrupt
Zhou Rui
vancasperz at yahoo.com.cn
Thu Mar 29 14:20:24 EST 2007
Hi
Sorry for my silly mistake, and I modify it like this:
#ifndef MODULE
#define MODULE
#endif
#ifndef __KERNEL__
#define __KERNEL__
#endif
#include <linux/module.h>
#include <linux/kernel.h>
#include <linux/types.h>
#include <linux/errno.h>
void hw_disable_irq (void) {
int c;
__asm__ __volatile__(
"mfmsr %%r0; \
wrteei 0; \
mfmsr %0;":"=r"(c) : );
printk("%x\n",c);
}
int init_module(void)
{
hw_disable_irq();
}
void cleanup_module(void)
{
}
MODULE_LICENSE("GPL");
I can get the output is 0x21030. But I also use BDI2000 here and when I halt the board from BDI2000, I get
405EP>halt
Core number : 0
Core state : debug mode
Debug entry cause : JTAG stop request
Current PC : 0xc00042d8
Current CR : 0x22004082
Current MSR : 0x00029030
Current LR : 0xc00042d8
Hope my understanding for big endian is right. It seems 0x00029030 in MSR is
00000000 00000010 10010000 00110000, but 0x21030 is
00000000 00000010 00010000 00110000.
It seems the 16th bit (EE) has been set to 0, but what should I do to make sure whether the external interrupt is disabled or not? Thank you very much.
Grant Likely <grant.likely at secretlab.ca> 写道: On 3/28/07, Zhou Rui wrote:
> Hi, all
> I am trying to disable interrupt on a PPC405EP board. I have checked
> from the 405 maunual that once the EE bit of MSR is set to 0, the external
> interrupt will be disabled. So I write a simple test module for that:
>
> #ifndef MODULE
> #define MODULE
> #endif
>
> #ifndef __KERNEL__
> #define __KERNEL__
> #endif
>
> #include
> #include
> #include
> #include
>
> void hw_disable_irq (void) {
> int c;
> __asm__ __volatile__(
> "mfmsr %%r0; \
> wrteei 0; \
> mfmsr %0;":"=r"(c) : );
>
> printk("%h\n",c);
> }
>
> int init_module(void)
> {
> }
>
> void cleanup_module(void)
> {
> }
>
> MODULE_LICENSE("GPL");
>
> When I insert this module, it seems nothing happens and there is no output
> of the varible "c". So would you like to tell me what the problem is here?
> Thank you very much.
Umm, because this modules doesn't do anything perhaps? You've
declared init and cleanup routines, but there are two problems with
them.
1. You haven't used the module_init and module_exit macros to actually
register them as init/exit routines.
2. They're empty
There is no possible way for your hw_disable_irq() routine to get called.
Cheers,
g.
--
Grant Likely, B.Sc. P.Eng.
Secret Lab Technologies Ltd.
grant.likely at secretlab.ca
(403) 399-0195
Sorry for my silly mistake, and I modify it like this:
#ifndef MODULE
#define MODULE
#endif
#ifndef __KERNEL__
#define __KERNEL__
#endif
#include <linux/module.h>
#include <linux/kernel.h>
#include <linux/types.h>
#include <linux/errno.h>
void hw_disable_irq (void) {
int c;
__asm__ __volatile__(
"mfmsr %%r0; \
wrteei 0; \
mfmsr %0;":"=r"(c) : );
printk("%x\n",c);
}
int init_module(void)
{
hw_disable_irq();
}
void cleanup_module(void)
{
}
MODULE_LICENSE("GPL");
I can get the output is 0x21030. But I also use BDI2000 here and when I halt the board from BDI2000, I get
405EP>halt
Core number : 0
Core state : debug mode
Debug entry cause : JTAG stop request
Current PC : 0xc00042d8
Current CR : 0x22004082
Current MSR : 0x00029030
Current LR : 0xc00042d8
Hope my understanding for big endian is right. It seems 0x00029030 in MSR is
00000000 00000010 10010000 00110000, but 0x21030 is
00000000 00000010 00010000 00110000.
It seems the 16th bit (EE) has been set to 0, but what should I do to make sure whether the external interrupt is disabled or not? Thank you very much.
Best wishes
Zhou Rui
Distributed and Embedded System Lab
Room 532, Information Building
School of Information Science
---------------------------------
抢注雅虎免费邮箱-3.5G容量,20M附件!
-------------- next part --------------
An HTML attachment was scrubbed...
URL: http://ozlabs.org/pipermail/linuxppc-embedded/attachments/20070329/56c1bed9/attachment.htm
More information about the Linuxppc-embedded
mailing list