Reboot Command Makes kernel to hang (MPC8560)
Ansari
ma.harounansari at gdatech.co.in
Thu Jul 26 16:55:38 EST 2007
Hi all,
Processor (MPC8560)
Whenever reboot command is given in the linux console. The processor gets reset and it loads bootloader , kernel and when uncompressing the ramdisk it gets hang. The sample log is given below. Any u please tell me what are the factors that can makes this to happen.
Log
----
070500 U-Boot 1.1.2 (May 30 2007 - 20:20:09)
Motorola PowerPC ProcessorID=00000000 Rev. PVR=80200020
Board: XXX MPC8560 [PowerQUICC III]
CPU: 660 MHz
CCB: 330 MHz
DDR: 165 MHz
Performing version scanning
I2C: ready
DRAM: Configuring UPM for NAND
Configuring UPM for MSC8122 DSI Port
Initializing DRAM
DDR: 256 MB
Relocating POST functions.
FLASH: 16 MB
L2 cache enabled: 256KB
In: serial
Out: serial
Err: serial
Net: MOTO ENET0: PHY is Intel LXT971A (1378e2)
MOTO ENET1: PHY is Intel LXT971A (1378e2)
MOTO ENET0, MOTO ENET1
POST I: Before relocation. <DEL> to start... 1
POST II: After relocation. <DEL> to start... 1
Micro Controller version 75
Hit any key to stop autoboot: 0
## Booting image at ffd00000 ...
Image Name: 070500 Linux-cscpp
Created: 2007-05-30 14:49:24 UTC
Image Type: PowerPC Linux Kernel Image (gzip compressed)
Data Size: 938254 Bytes = 916.3 kB
Load Address: 00000000
Entry Point: 00000000
Verifying Checksum ... OK
Uncompressing Kernel Image ... OK
## Loading RAMDisk Image at ff000000 ...
Image Name: 070500 cscpp-REL_7_5
Created: 2007-05-30 14:51:09 UTC
Image Type: PowerPC Linux RAMDisk Image (gzip compressed)
Data Size: 3543240 Bytes = 3.4 MB
Load Address: 00000000
Entry Point: 00000000
Verifying Checksum ... OK
Loading Ramdisk to 0fc4e000, end 0ffaf0c8 ... OK
Memory CAM mapping: CAM0=256Mb, CAM1=0Mb, CAM2=0Mb residual: 0Mb
Linux version 2.4.20_mvlcge31-cscpp-7.5 (root at turing) (gcc version 3.3.1 (MontaVista 3.3.1-3.0.10.0300532 2003-12-24)) #1 Wed May 30 20:14:43 IST 2007
max_pfn = 8192
On node 0 totalpages: 65536
zone(0): 65536 pages.
zone(1): 0 pages.
zone(2): 0 pages.
Kernel command line: root=/dev/ram rw console=ttyS0,115200 ip=off
OpenPIC Version 1.2 (1 CPUs and 44 IRQ sources) at fdf80000
time_init: decrementer frequency = 41.250000 MHz
hr_time_init: arch_to_nsec = 50840048, nsec_to_arch = 177167400
Calibrating delay loop... 658.63 BogoMIPS
Memory: 253056k available (1696k kernel code, 760k data, 68k init, 0k highmem)
RMON - kernel resource monitoring
Dentry cache hash table entries: 32768 (order: 6, 262144 bytes)
Inode cache hash table entries: 16384 (order: 5, 131072 bytes)
Mount-cache hash table entries: 4096 (order: 3, 32768 bytes)
Buffer-cache hash table entries: 16384 (order: 4, 65536 bytes)
Page-cache hash table entries: 65536 (order: 6, 262144 bytes)
POSIX conformance testing by UNIFIX
Linux NET4.0 for Linux 2.4
Based upon Swansea University Computer Society NET3.039
Initializing RT netlink socket
LSP Revision 14
ikconfig 0.5 with /proc/ikconfig
Starting kswapd
Journalled Block Device driver loaded
JFFS version 1.0, (C) 1999, 2000 Axis Communications AB
JFFS2 version 2.1. (C) 2001, 2002 Red Hat, Inc., designed by Axis Communications AB.
CPM UART driver version 0.01
ttyS0 on SCC1 at 0x8000, BRG1
pty: 256 Unix98 ptys configured
eth0: FCC ENET Version 0.3, 02:e0:0c:80:31:03
eth0: RMON initialized
RAMDISK driver initialized: 16 RAM disks of 32768K size 1024 blocksize
loop: loaded (max 8 devices)
eth1: Gianfar Ethernet Controller Version 1.0, 02:e0:0c:00:31:03
eth1: Running with NAPI disabled
eth1: 64/64 RX/TX BD ring size
eth1: RMON initialized
eth2: Gianfar Ethernet Controller Version 1.0, 02:e0:0c:00:31:02
eth2: Running with NAPI disabled
eth2: 64/64 RX/TX BD ring size
eth2: RMON initialized
network device driver for LKCD registered
Crash dump driver initialized.
CSC flash: Found 1 x16 devices at 0x0 in 16-bit bank
Intel/Sharp Extended Query Table at 0x0031
Using buffer write method
cfi_cmdset_0001: Erase suspend on write enabled
Creating 7 MTD partitions on "CSC flash":
0x00f80000-0x01000000 : "uboot"
0x00d00000-0x00e00000 : "kernel0"
0x00e00000-0x00f00000 : "kernel1"
0x00700000-0x00d00000 : "app"
0x00000000-0x00380000 : "root0"
0x00380000-0x00700000 : "root1"
0x00f00000-0x00f80000 : "env"
Creating 2 MTD partitions on "CSC NVRAM":
0x00000000-0x00010000 : "applog"
0x00010000-0x00020000 : "kernellog"
NAND device: Manufacturer ID: 0x2c, Chip ID: 0xca (Unknown NAND 256MiB 3,3V 16-bit)
Scanning device for bad blocks
Bad eraseblock 1780 at 0x0de80000
Creating 1 MTD partitions on "NAND 256MiB 3,3V 16-bit":
0x00000000-0x10000000 : "NAND Partition"
NET4: Linux TCP/IP 1.0 for NET4.0
IP Protocols: ICMP, UDP, TCP, IGMP
IP: routing cache hash table of 2048 buckets, 16Kbytes
TCP: Hash tables configured (established 16384 bind 32768)
ip_conntrack version 2.1 (2048 buckets, 16384 max) - 296 bytes per conntrack
ip_tables: (C) 2000-2002 Netfilter core team
NET4: Unix domain sockets 1.0/SMP for Linux NET4.0.
Event Broker Driver (C) 2001,2002 MontaVista Software (source at mvista.com)
Done starting sysfs
RAMDISK: Compressed image found at block 0
Freeing initrd memory: 3460k freed
VFS: Mounted root (ext2 filesystem).
Freeing unused kernel memory: 68k init
Welcome to Linux Group
Starting system...
Mounting /proc: done.
Brining up loopback interface: done.
Mounting /tmp: done.
Starting syslogd: done.
Starting klogd: done.
Starting telnetd: done.
MC-I2C DRIVER Successfully Installed
mcc: mcc_dev_siram_entries_config: siram config: start entry: 0, start channel: 128, count: 64
mcc: mcc_dev_siram_entries_config: siram config: start entry: 128, start channel: 192, count: 64
mcc: mcc_dev_iopin_init: IO port init done
mcc: mcc_dev_clock_mux_init: clock mux init done 0x88
mcc: mcc_dev_init: Board specific init done.
mcc: mcc_dev_init: BDs init done
mcc: mcc_dev_init: global param init done
mcc: mcc_dev_init: extra channel param init done
mcc: mcc_dev_init: channel param init done
[: 1: unknown operand
DSP-7116: Driver registered.
DSP MSC 7116 Driver for HDI Interface May 30 2007 20:19:35
DSP-7116: Insmoded Successfully Default Status & Control Register 426 6618
MSC8122_DSI driver registered.
MSC8122_DSI Driver for DSI Interface May 30 2007 20:19:35DSI init...[2]
loading LSCL module...May 30 2007 ,20:19:36
scc at 0x8100
sccp 0xd2575a20
priv size 176
dev name lscl0
scc1 clk 0x000100b2
device lscl0
lscl module loaded
Setting the LSCL address & IP address
setting slot id 0x0021
bonding.c:v2.2.5 (May 22, 2003)
bonding_init(): eth1 primary device specified but has no effect in fault-tolerance (broadcast) mode
bond0 registered with MII link monitoring set to 200 ms, in fault-tolerance (broadcast) mode.
bond0 registered without ARP monitoring
eth1: PHY is Intel LXT971A (1378e2)
eth1: No link detected
bond0: enslaving eth1 as an active interface with a down link.
eth1: Auto-negotiation done
eth1: Full Duplex
eth1: Speed 100BT
eth1: Link is up
eth2: PHY is Intel LXT971A (1378e2)
eth2: No link detected
bond0: enslaving eth2 as an active interface with a down link.
eth2: Auto-negotiation done
eth2: Full Duplex
eth2: Speed 100BT
eth2: Link is up
Setting system time from hardware clock.
yaffs: dev is 7945 name is "1f:09"
bond0: link status definitely up for interface eth2.
bond0: link status definitely up for interface eth1.
jffs2_scan_eraseblock(): Magic bitmask 0x1985 not found at 0x00000000: 0xd355 instead
jffs2_scan_eraseblock(): Magic bitmask 0x1985 not found at 0x00000004: 0xcf85 instead
jffs2_scan_eraseblock(): Magic bitmask 0x1985 not found at 0x00000008: 0x435c instead
jffs2_scan_eraseblock(): Magic bitmask 0x1985 not found at 0x0000000c: 0xc451 instead
jffs2_scan_eraseblock(): Magic bitmask 0x1985 not found at 0x00000010: 0xb677 instead
jffs2_scan_eraseblock(): Magic bitmask 0x1985 not found at 0x00000014: 0x15f5 instead
jffs2_scan_eraseblock(): Magic bitmask 0x1985 not found at 0x00000018: 0xfbfb instead
jffs2_scan_eraseblock(): Magic bitmask 0x1985 not found at 0x0000001c: 0x4491 instead
jffs2_scan_eraseblock(): Magic bitmask 0x1985 not found at 0x00000020: 0x543a instead
jffs2_scan_eraseblock(): Magic bitmask 0x1985 not found at 0x00000024: 0x1193 instead
Further such events for this erase block will not be printed
Cowardly refusing to erase blocks on filesystem with no valid JFFS2 nodes
empty_blocks 0, bad_blocks 0, c->nr_blocks 16
mount: Mounting /dev/mtdblock7 on /mnt/app-nvram failed: Invalid argument
Punching Microcontroller.
Creating TSI LOCK fileDone
Starting the xxx agent
====== SYSTEM STARTED ======
System started
_____ _ _ _ _ __ _ _
/ ____|| \ | || | | | / /| | (_)
| | __ | \| || | | | / / | | _ _ __ _ _ __ __
| | |_ || . || | | | / / | | | || '_ \ | | | |\ \/ /
| |__| || |\ || |__| | / / | |____ | || | | || |_| | > <
\_____||_| \_| \____/ /_/ |______||_||_| |_| \__,_|/_/\_\
(none) login: root
BusyBox v1.1.0 (2006.03.23-09:02+0000) Built-in shell (ash)
Enter 'help' for a list of built-in commands.
[root@(none) /root]# reboot
The system is going down NOW !!
Sending SIGTERM to all processeExiting Syslogd!
Sending SIGKILL to all processes.
Please stand by while rebooting the system.
Restarting systemste?
070500 U-Boot 1.1.2 (May 30 2007 - 20:20:09)
Motorola PowerPC ProcessorID=00000000 Rev. PVR=80200020
Board: XXX MPC8560 [PowerQUICC III]
CPU: 660 MHz
CCB: 330 MHz
DDR: 165 MHz
Performing version scanning
I2C: ready
DRAM: Configuring UPM for NAND
Configuring UPM for MSC8122 DSI Port
Initializing DRAM
DDR: 256 MB
Relocating POST functions.
FLASH: 16 MB
L2 cache enabled: 256KB
In: serial
Out: serial
Err: serial
Net: MOTO ENET0: PHY is Intel LXT971A (1378e2)
MOTO ENET1: PHY is Intel LXT971A (1378e2)
MOTO ENET0, MOTO ENET1
POST I: Before relocation. <DEL> to start... 1
POST II: After relocation. <DEL> to start... 1
Micro Controller version 75
Hit any key to stop autoboot: 0
## Booting image at ffd00000 ...
Image Name: 070500 Linux-cscpp
Created: 2007-05-30 14:49:24 UTC
Image Type: PowerPC Linux Kernel Image (gzip compressed)
Data Size: 938254 Bytes = 916.3 kB
Load Address: 00000000
Entry Point: 00000000
Verifying Checksum ... OK
Uncompressing Kernel Image ... OK
## Loading RAMDisk Image at ff000000 ...
Image Name: 070500 cscpp-REL_7_5
Created: 2007-05-30 14:51:09 UTC
Image Type: PowerPC Linux RAMDisk Image (gzip compressed)
Data Size: 3543240 Bytes = 3.4 MB
Load Address: 00000000
Entry Point: 00000000
Verifying Checksum ... OK
Loading Ramdisk to 0fc4e000, end 0ffaf0c8 ... OK
Memory CAM mapping: CAM0=256Mb, CAM1=0Mb, CAM2=0Mb residual: 0Mb
Linux version 2.4.20_mvlcge31-cscpp-7.5 (root at turing) (gcc version 3.3.1 (MontaVista 3.3.1-3.0.10.0300532 2003-12-24)) #1 Wed May 30 20:14:43 IST 2007
max_pfn = 8192
On node 0 totalpages: 65536
zone(0): 65536 pages.
zone(1): 0 pages.
zone(2): 0 pages.
Kernel command line: root=/dev/ram rw console=ttyS0,115200 ip=off
OpenPIC Version 1.2 (1 CPUs and 44 IRQ sources) at fdf80000
time_init: decrementer frequency = 41.250000 MHz
hr_time_init: arch_to_nsec = 50840048, nsec_to_arch = 177167400
Calibrating delay loop... 658.63 BogoMIPS
Memory: 253056k available (1696k kernel code, 760k data, 68k init, 0k highmem)
RMON - kernel resource monitoring
Dentry cache hash table entries: 32768 (order: 6, 262144 bytes)
Inode cache hash table entries: 16384 (order: 5, 131072 bytes)
Mount-cache hash table entries: 4096 (order: 3, 32768 bytes)
Buffer-cache hash table entries: 16384 (order: 4, 65536 bytes)
Page-cache hash table entries: 65536 (order: 6, 262144 bytes)
POSIX conformance testing by UNIFIX
Linux NET4.0 for Linux 2.4
Based upon Swansea University Computer Society NET3.039
Initializing RT netlink socket
LSP Revision 14
ikconfig 0.5 with /proc/ikconfig
Starting kswapd
Journalled Block Device driver loaded
JFFS version 1.0, (C) 1999, 2000 Axis Communications AB
JFFS2 version 2.1. (C) 2001, 2002 Red Hat, Inc., designed by Axis Communications AB.
CPM UART driver version 0.01
ttyS0 on SCC1 at 0x8000, BRG1
pty: 256 Unix98 ptys configured
eth0: FCC ENET Version 0.3, 02:e0:0c:80:31:03
eth0: RMON initialized
RAMDISK driver initialized: 16 RAM disks of 32768K size 1024 blocksize
loop: loaded (max 8 devices)
eth1: Gianfar Ethernet Controller Version 1.0, 02:e0:0c:00:31:03
eth1: Running with NAPI disabled
eth1: 64/64 RX/TX BD ring size
eth1: RMON initialized
eth2: Gianfar Ethernet Controller Version 1.0, 02:e0:0c:00:31:02
eth2: Running with NAPI disabled
eth2: 64/64 RX/TX BD ring size
eth2: RMON initialized
network device driver for LKCD registered
Crash dump driver initialized.
CSC flash: Found 1 x16 devices at 0x0 in 16-bit bank
Intel/Sharp Extended Query Table at 0x0031
Using buffer write method
cfi_cmdset_0001: Erase suspend on write enabled
Creating 7 MTD partitions on "CSC flash":
0x00f80000-0x01000000 : "uboot"
0x00d00000-0x00e00000 : "kernel0"
0x00e00000-0x00f00000 : "kernel1"
0x00700000-0x00d00000 : "app"
0x00000000-0x00380000 : "root0"
0x00380000-0x00700000 : "root1"
0x00f00000-0x00f80000 : "env"
Creating 2 MTD partitions on "CSC NVRAM":
0x00000000-0x00010000 : "applog"
0x00010000-0x00020000 : "kernellog"
NAND device: Manufacturer ID: 0x2c, Chip ID: 0xca (Unknown NAND 256MiB 3,3V 16-bit)
Scanning device for bad blocks
Bad eraseblock 1780 at 0x0de80000
Creating 1 MTD partitions on "NAND 256MiB 3,3V 16-bit":
0x00000000-0x10000000 : "NAND Partition"
NET4: Linux TCP/IP 1.0 for NET4.0
IP Protocols: ICMP, UDP, TCP, IGMP
IP: routing cache hash table of 2048 buckets, 16Kbytes
TCP: Hash tables configured (established 16384 bind 32768)
ip_conntrack version 2.1 (2048 buckets, 16384 max) - 296 bytes per conntrack
ip_tables: (C) 2000-2002 Netfilter core team
NET4: Unix domain sockets 1.0/SMP for Linux NET4.0.
Event Broker Driver (C) 2001,2002 MontaVista Software (source at mvista.com)
Done starting sysfs
RAMDISK: Compressed image found at block 0
<<<<<<<<<<<<<<<<<<<<<<<<<<<<<<<<<<<<<<<<<<<<<<<<<<<<<<<<<<<<<<<<<<<<<<<Hangs Here>>>>>>>>>>>>>>>>>>>>>>
Thanks in advance
Haroun Ansari M A
-------------- next part --------------
An HTML attachment was scrubbed...
URL: http://ozlabs.org/pipermail/linuxppc-embedded/attachments/20070726/8e8ce313/attachment-0001.htm
More information about the Linuxppc-embedded
mailing list