booting 2.6 kernel on ML403

[Ameet Patil]

Hi Pradeep,

Pradeep Sampath wrote:
> Hello Ameet/Ming!
>  
> I am running linux kernel 2.6 on a ML403. Your posts on the list was 
> extremely helpful and saved a lot of time. But i have ran into a 
> number of issues and need your help. I have described both the scenarios.
>  
> Problem 1:
> I followed the steps described in 
> http://www.linux.get2knowmore.com/2006/06/30/quick-guide-linux-26-on-xilinx-virtex-ii-pro-boards-part-i/
> After the kernel boots towards the end i get a failure - 
> unknown-block(0,0)
> [    3.012128] VFS: Cannot open root device "sda2" or unknown-block(0,0)
> [    3.088465] Please append a correct "root=" boot option
> [    3.150933] Kernel panic - not syncing: VFS: Unable to mount root 
> fs on unkno
> wn-block(0,0)
> [    3.249891]  <0>Rebooting in 180 seconds..
>  
> On the linux partition of my CF card i created the following block 
> device files
> # mknod -m 660 console c 5 1
> # mknod -m 660 sda b 254 0
> # mknod -m 660 sda1 b 254 1
> # mknod -m 660 sda2 b 254 2
> # mknod -m 660 sda3 b 254 3
Note: my driver creates device xsa and not sda. so create xsa, xsa1, 
xsa2, etc. in /dev of your CF card instead of sda.
> mkdir tts
> # mknod -m 660 0 b 4 64
please check: this should be a character device. Hence use:
# mknod -m 660 0 c 4 64
>
> But the result was same as above.
> What should be my default bootloader kernel arguments?
> console=ttyS0,9600 root=/dev/sda2
> or
> console=ttyS0,9600 root=/dev/xsa2
yes! root=/dev/xsa2. This is the right root parameter.
> or
> console=ttyS0,9600 root=/dev/xsysace/disc0/part2 rw
>  
> I am confused. How do we determine the device name of the CF card?
>  
> I have 2 partitions on my CF card - Partition1 is DOS FAT16 partition, 
> Partition2 is Linux with ext3 filesystem.
>
>  
> Here is the full log of the serial terminal:
> Linux/PPC load: console=ttyS0,9600 root=/dev/sda2
> Uncompressing Linux...done.
> Now booting the kernel
> [    0.000000] Linux version 2.6.17.1 (psampath at psampath-test 
> <mailto:psampath at psampath-test>) (gcc version 3.4.
> 1) #3 Mon Oct 2 14:43:23 PDT 2006
> [    0.000000] Xilinx ML403 Reference System (Virtex-4 FX)
> [    0.000000] Built 1 zonelists
> [    0.000000] Kernel command line: console=ttyS0,9600 root=/dev/sda2
> [    0.000000] Xilinx INTC #0 at 0xD1000FC0 mapped to 0xFDFFEFC0
> [    0.000000] PID hash table entries: 512 (order: 9, 2048 bytes)
> [    0.000166] Console: colour dummy device 80x25
> [    0.000650] Dentry cache hash table entries: 8192 (order: 3, 32768 
> bytes)
> [    0.001465] Inode-cache hash table entries: 4096 (order: 2, 16384 
> bytes)
> [    0.014853] Memory: 62524k available (1736k kernel code, 552k data, 
> 84k init,
>  0k highmem)
> [    0.104274] Security Framework v1.0.0 initialized
> [    0.104471] Mount-cache hash table entries: 512
> [    0.110096] NET: Registered protocol family 16
> [    0.118276] NET: Registered protocol family 2
> [    0.152515] IP route cache hash table entries: 512 (order: -1, 2048 
> bytes)
> [    0.153502] TCP established hash table entries: 2048 (order: 1, 
> 8192 bytes)
> [    0.153689] TCP bind hash table entries: 1024 (order: 0, 4096 bytes)
> [    0.153787] TCP: Hash tables configured (established 2048 bind 1024)
> [    0.153814] TCP reno registered
> [    0.161503] VFS: Disk quotas dquot_6.5.1
> [    0.161747] Dquot-cache hash table entries: 1024 (order 0, 4096 bytes)
> [    0.162380] Initializing Cryptographic API
> [    0.162433] io scheduler noop registered
> [    0.162534] io scheduler anticipatory registered (default)
> [    0.162630] io scheduler deadline registered
> [    0.162764] io scheduler cfq registered
> [    0.773694] Serial: 8250/16550 driver $Revision: 1.90 $ 4 ports, 
> IRQ sharing
> enabled
> [    0.782331] serial8250.0: ttyS0 at MMIO 0xa0001003 (irq = 9) is a 16450
> [    2.663867] RAMDISK driver initialized: 16 RAM disks of 300000K 
> size 1024 blo
> cksize
> [    2.758159] i8042.c: No controller found.
> [    2.806550] mice: PS/2 mouse device common for all mice
> [    2.869032] TCP bic registered
> [    2.904787] NET: Registered protocol family 8
> [    2.956790] NET: Registered protocol family 20
> [    3.012128] VFS: Cannot open root device "sda2" or unknown-block(0,0)
> [    3.088465] Please append a correct "root=" boot option
> [    3.150933] Kernel panic - not syncing: VFS: Unable to mount root 
> fs on unkno
> wn-block(0,0)
> [    3.249891]  <0>Rebooting in 180 seconds..
>  
> Problem 2:
> - Untar the kernel 2.6.17.1
> - Applied the 5 TEMAC patches
> - Applied Ameet's Sysace patch
which patch did you apply? For TEMAC... apply the following patch: 
http://www.cs.york.ac.uk/rtslab/demos/amos/xupv2pro/patches/linuxppc-2.6.17.1-sysace-1.2-after-TEMAC.patch

cheers,
-Ameet
> - copied the xparameters_ml403.h to the 
> arch/ppc/platforms/4xx/xparameters/xparameters_ml403.h generated by EDK
>  
> - After including the network driver and sysace driver in "make 
> menuconfig" and generating the zImage and booting the board the kernel 
> hangs.
>  
> loaded at:     00400000 0051613C
> board data at: 00514124 0051413C
> relocated to:  004050E8 00405100
> zimage at:     00405881 005137E8
> avail ram:     00517000 10000000
> Linux/PPC load: console=ttyS0,9600 root=/dev/sda2
> Uncompressing Linux...done.
> Now booting the kernel
> I suspect the xparameter addresses are incorrect. Which parameter 
> should i modify in the xparameters_ml403.h?
>  
> Kindly send a reply at your earliest.
> Thanks!
> Pradeep