minor progress with plb_temac v3.00a, EDK 8.2, & 2.6.18.1
David H. Lynch Jr.
dhlii at dlasys.net
Sun Nov 5 10:20:29 EST 2006
robert corley wrote:
> Pradeep;
>
> Booting with a ramdisk is a matter of putting the appropriate image in
> the arch/ppc/boot/images directory (I obtained mine from the gsrd
> design files), adding the root=/dev/ram rw on the command-line boot
> options, making the .config changes for ram disk support and initrd
> usage, and issuing a make zImage.initrd command.
>
> Beware when upgrading to 2.6.18.1 as you may have difficulties with
> the adapter.c you obtained previously. The adapter.c in EDK 8.2 is
> not as easy to find. Using the EDK to generate software components
> for linux will not expose the proper adapter.c. I had to use the path
> that Rick Moleres posted earlier to retrieve the adapter.c which I
> used for 2.6.18.1 and in my notes.
>
> -cy
>
I am booting with a ramdisk using initramfs. Aside from its being
somewhat harder to find documentation I beleive it is actually easier.
In the simplest form, create a directory on your host that contains
exactly what you want on the ramdisk.
Enable CONFIG_INITRAMFS
and point the CONFIG_INITRAMFS_SOURCE to that directory.
It is pretty much that simple. The linux build process creates a
kernel - I use zImage.elf that has the ramdisk compressed and concatentated.
Nothing except the Linux kernel itself has to make any accomidations
for the ramdisk. The bootloader does not have to deal with another file,
or pass pointers to it to Linux, ....
It took some time to get it working - mostly because I did nto know
what I was doing, but in hindsight it is really easy.
> ----- Original Message ----
> From: Pradeep Sampath <pradeepsampath at yahoo.com>
> To: robert corley <rdcorle at yahoo.com>
> Sent: Thursday, November 2, 2006 7:57:25 PM
> Subject: Re: minor progress with plb_temac v3.00a, EDK 8.2, & 2.6.18.1
>
> This is great! I played around for a while with the Sysace CF driver
> patches and got it to work. Since you are booting with ramdisk image
> would you be kind enough to add more text on how to do that? I see
> that you are using UART Lite? Does it require any special setting for
> the boot logs to show up on the standard hyperterminal.
>
> I am planning on rebuilding the whole system using EDK 8.2 and linux
> kernel 2.6.18.1.
>
> -Pradeep
>
> */robert corley <rdcorle at yahoo.com>/* wrote:
>
> For those interested, I have acheived some measure of success with
> the plb_temac driver.
>
> I have attached a txt file of what I had to do to get it working
> under 2.6.18.1
>
> I am using the plb_temac in DMA mode 3
>
> Below you will see the boot dump.
>
> For those able to help, can anyone provide insight as to the
> failure of setting PHY link speed?
>
> -cy
>
>
>
> ====================
> ----------------------------------------------------------------------
> 2.6.18.1 kernel with all patches
> 11/02/2006 15:30
> plb_temac v3.00a
> hard_temac v3.00b
>
>
> loaded at: 00400000 009F1138
> board data at: 009EF120 009EF138
> relocated to: 004040B4 004040CC
> zimage at: 00404EC7 0057C1F2
> initrd at: 0057D000 009EE6FE
> avail ram: 009F2000 04000000
>
>
> Linux/PPC load: console=ttyUL0 single
> ip=192.168.1.100:192.168.1.144:192.168.1.1:255.255.255.0:nab::
> ramdisk_size=4660000 root=/dev/ram rw
>
> Uncompressing Linux...done.
>
> Now booting the kernel
>
> [ 0.000000] Linux version 2.6.18.1 (rdcorle at athena) (gcc version
> 3.4.2) #2 Thu Nov 2 21:56:32 UTC 2006
> [ 0.000000] Xilinx ML403 Reference System (Virtex-4 FX)
> [ 0.000000] Built 1 zonelists. Total pages: 16384
> [ 0.000000] Kernel command line: console=ttyUL0 single
> ip=192.168.1.100:192.168.1.144:192.168.1.1:255.255.255.0:nab::
> ramdisk_size=4660000 root=/dev/ram rw
> [ 0.000000] Xilinx INTC #0 at 0xD1000FC0 mapped to 0xFDFFFFC0
> [ 0.000000] PID hash table entries: 512 (order: 9, 2048 bytes)
> [ 0.000158] Console: colour dummy device 80x25
> [ 0.000568] Dentry cache hash table entries: 8192 (order: 3, 32768
> bytes)
> [ 0.001277] Inode-cache hash table entries: 4096 (order: 2, 16384
> bytes)
> [ 0.012895] Memory: 57060k available (2548k kernel code, 640k
> data, 96k init, 0k highmem)
> [ 0.104378] Mount-cache hash table entries: 512
> [ 0.106721] checking if image is initramfs...it isn't (no cpio
> magic); looks like an initrd
> [ 2.414242] Freeing initrd memory: 4549k freed
> [ 2.418712] NET: Registered protocol family 16
> [ 2.427313] NET: Registered protocol family 2
> [ 2.464244] IP route cache hash table entries: 512 (order: -1,
> 2048 bytes)
> [ 2.465037] TCP established hash table entries: 2048 (order: 1,
> 8192 bytes)
> [ 2.465205] TCP bind hash table entries: 1024 (order: 0, 4096 bytes)
> [ 2.465296] TCP: Hash tables configured (established 2048 bind 1024)
> [ 2.465324] TCP reno registered
> [ 2.474633] NTFS driver 2.1.27 [Flags: R/O].
> [ 2.475046] JFS: nTxBlock = 481, nTxLock = 3854
> [ 2.477623] SGI XFS with no debug enabled
> [ 2.479001] io scheduler noop registered
> [ 2.479109] io scheduler anticipatory registered
> [ 2.479197] io scheduler deadline registered
> [ 2.479402] io scheduler cfq registered (default)
> [ 2.517627] uartlite.0: ttyUL0 at MMIO 0xa0000000 (irq = 1) is a
> uartlite
> [ 2.691029] RAMDISK driver initialized: 16 RAM disks of 4660000K
> size 1024 blocksize
> [ 2.703933] loop: loaded (max 8 devices)
> [ 2.709698] XTemac: using sgDMA mode.
> [ 2.713493] XTemac: using TxDRE mode
> [ 2.717081] XTemac: using RxDRE mode
> [ 2.720678] XTemac: buffer descriptor size: 32768 (0x8000)
> [ 2.726622] XTemac: (buffer_descriptor_init) phy: 0x580000, virt:
> 0xff100000, size: 0x8000
> [ 2.741073] eth0: Xilinx TEMAC #0 at 0x60000000 mapped to
> 0xC5050000, irq=0
> [ 2.748080] eth0: XTemac id 1.0f, block id 5, type 8
> [ 2.753636] mice: PS/2 mouse device common for all mice
> [ 2.759529] TCP bic registered
> [ 3.264317] eth0: XTemac: Options: 0xb8f2
> [ 15.227339] eth0: XTemac: Not able to set the speed to 1000
> (status: 0x148)
> [ 25.200394] eth0: XTemac: Not able to set the speed to 100
> (status: 0x148)
> [ 35.173357] eth0: XTemac: Not able to set the speed to 10
> (status: 0x148)
> [ 35.180122] eth0: XTemac: could not negotiate speed
> [ 35.187740] eth0: XTemac: Send Threshold = 16, Receive Threshold = 2
> [ 35.194116] eth0: XTemac: Send Wait bound = 1, Receive Wait bound = 1
> [ 36.205399] IP-Config: Complete:
> [ 36.208459] device=eth0, addr=192.168.1.100, mask=255.255.255.0,
> gw=192.168.1.1,
> [ 36.216339] host=nab, domain=, nis-domain=(none),
> [ 36.221487] bootserver=192.168.1.144, rootserver=192.168.1.144,
> rootpath=
> [ 36.229826] RAMDISK: Compressed image found at block 0
> [ 37.200498] eth0: XTemac: PHY Link carrier lost.
> [ 39.097820] VFS: Mounted root (ext2 filesystem).
> [ 39.102751] Freeing unused kernel memory: 96k init
> [ 39.108356] ulite_startup: UART status = 0x0014
> [ 39.124619] ulite_startup: UART status = 0x0014
> [ 39.134313] ulite_startup: UART status = 0x0014
>
>
> BusyBox v1.00-pre9 (2004.04.18-19:53+0000) Built-in shell (ash)
> Enter 'help' for a list of built-in commands.
>
> -sh: can't access tty; job control turned off
>
>
> steps for plb_temac drivers under EDK 8.2.02i (w/SP2.4+0)
> Using plb_temac v3.00a & hard_temac v3.00b
>
> Generate s/w libraries
>
> 1. copy or ftp the following files from
> C:\EDK\sw\ThirdParty\bsp\linux_2_6_v1_00_a\linux\
> to the base directory of the linux source tree
>
> USED:
> arch\ppc\platforms\4xx\xparameters\xparameters.h
>
> ** UNUSED
> arch\ppc\platforms\4xx\virtex.c
> arch\ppc\boot\simple\embed_config.c
> include\linux\xilinx_devices.h
>
> 2. copy
> C:\EDK\sw\ThirdParty\bsp\linux_2_6_v1_00_a\drivers\temac_linux_2_6_v2_00_b\src\adapter.c
> to
> ../drivers/net/xilinx_temac/adapter.c
>
> 3. copy or ftp ..\linux\arch\ppc\platforms\xilinx_ocp =>
> drivers/xilinx_edk
> Note: Remove all old files first *except* Kconfig, xio.h
>
> 4. modify drivers/xilinx_edk/Makefile with the following to look
> like this:
>
> # Linux file to EXPORT_SYMBOL all of the Xilinx entries.
> obj-$(CONFIG_XILINX_EDK) += xilinx_syms.o
> #
> # # The Xilinx OS independent code.
> xilinx_syms-objs := xbasic_types.o \
> xdmav3.o xdmav3_intr.o xdmav3_selftest.o xdmav3_simple.o xdmav3_sg.o \
> xipif_v1_23_b.o \
> xpacket_fifo_l_v2_00_a.o xpacket_fifo_v2_00_a.o \
> xversion.o
>
> 5. Modify your copied xparameters_ml403.h (see notes below) as
> follows:
> add these lines after #define XPAR_PLB_TEMAC_0_INCLUDE_RX_CSUM
>
> #define XPAR_TEMAC_0_IPIF_RDFIFO_DEPTH XPAR_PLB_TEMAC_0_RXFIFO_DEPTH
> #define XPAR_TEMAC_0_IPIF_WRFIFO_DEPTH XPAR_PLB_TEMAC_0_TXFIFO_DEPTH
> #define XPAR_TEMAC_0_MAC_FIFO_DEPTH XPAR_PLB_TEMAC_0_MAC_FIFO_DEPTH
> #define XPAR_TEMAC_0_TEMAC_DCR_HOST 0
> #define XPAR_TEMAC_0_INCLUDE_DRE 1
>
>
> 6. (optional) modify arch/ppc/platforms/virtex.h to accomodate
> RX_CSUM XPAR
>
> struct xtemac_platform_data {
> #ifdef XPAR_TEMAC_0_INCLUDE_RX_CSUM
> u8 tx_dre;
> u8 rx_dre;
> u8 tx_csum;
> u8 rx_csum;
> u8 phy_type;
> #endif
> u8 dma_mode;
> u32 rx_pkt_fifo_depth;
> u32 tx_pkt_fifo_depth;
> u16 mac_fifo_depth;
> u8 dcr_host;
> u8 dre;
> u8 mac_addr[6];
> };
>
> 7. Modify ../drivers/net/xilinx_temac/adapter.c to remove #include and
> add #include
> add #include
>
> ____________________________________________________________________________________
> NOTES:
> 1. Don't forget to copy EDK-generated xparameters.h to
> ../arch/ppc/platforms/4xx/xparameters/xparameters_ml403.h
>
>
>
> =====================================================
> Files in latest patch:
> ../drivers/net/xilinx_temac =
> Makefile
> adapter.c
> xtemac.c
> xtemac_control.c
> xtemac_fifo.c
> xtemac_intr.c
> xtemac_intr_fifo.c
> xtemac_intr_sgdma.c
> xtemac_l.c
> xtemac_sgdma.c
> xtemac.h
> xtemac_i.h
> xtemac_l.h
>
> Files in ..\linux\drivers\net\xilinx_temac => (** = new files)
>
> Makefile
> adapter.c
> xtemac.c
> xtemac_control.c
> xtemac_fifo.c
> xtemac_g.c**
> xtemac_intr.c
> xtemac_intr_fifo.c
> xtemac_intr_sgdma.c
> xtemac_l.c
> xtemac_selftest.c**
> xtemac_sgdma.c
> xtemac_sinit.c**
> xtemac_stats.c**
> xtemac.h
> xtemac_i.h
> xtemac_l.h
>
> ============================================================
> Files in ../drivers/xilinx_edk =>
>
> Kconfig
> Makefile
> xbasic_types.c
> xdmav2.c
> xdmav2_intr.c
> xdmav2_sg.c
> xdmav2_simple.c
> xilinx_syms.c
> xpacket_fifo_l_v2_00_a.c
> xpacket_fifo_v2_00_a.c
> xbasic_types.h
> xdmabdv2.h
> xdmav2.h
> xdmav2_l.h
> xio.h
> xpacket_fifo_l_v2_00_a.h
> xpacket_fifo_v2_00_a.h
> xstatus.h
>
> Files in ..\linux\arch\ppc\platforms\xilinx_ocp=>
> Makefile
> xbasic_types.c
> xutil_memtest.c
> xpacket_fifo_v2_00_a.c
> xdmav3.c
> xpacket_fifo_l_v2_00_a.c
> xdmav3_intr.c
> xipif_v1_23_b.c
> xdmav3_selftest.c
> xdmav3_sg.c
> xdmav3_simple.c
> xversion.c
> xenv.h
> xenv_none.h
> xenv_vxworks.h
> xdmav3_l.h
> xipif_v1_23_b.h
> xdmav3.h
> xpacket_fifo_l_v2_00_a.h
> xdmabdv3.h
> xpacket_fifo_v2_00_a.h
> xparameters_ml300.h
> xstatus.h
> xutil.h
> xbasic_types.h
> xenv_linux.h
> xversion.h
> _______________________________________________
> Linuxppc-embedded mailing list
> Linuxppc-embedded at ozlabs.org
> https://ozlabs.org/mailman/listinfo/linuxppc-embedded
>
>
>
> ------------------------------------------------------------------------
>
> _______________________________________________
> Linuxppc-embedded mailing list
> Linuxppc-embedded at ozlabs.org
> https://ozlabs.org/mailman/listinfo/linuxppc-embedded
--
Dave Lynch DLA Systems
Software Development: Embedded Linux
717.627.3770 dhlii at dlasys.net http://www.dlasys.net
fax: 1.253.369.9244 Cell: 1.717.587.7774
Over 25 years' experience in platforms, languages, and technologies too numerous to list.
"Any intelligent fool can make things bigger and more complex... It takes a touch of genius - and a lot of courage to move in the opposite direction."
Albert Einstein
-------------- next part --------------
An HTML attachment was scrubbed...
URL: http://ozlabs.org/pipermail/linuxppc-embedded/attachments/20061104/cd78d79d/attachment.htm
More information about the Linuxppc-embedded
mailing list