[RFC][PATCH 2.6.12-rc2 1/3] FCC Ethernet PlatformDevice support for 82xx

[Kumar Gala]

Can you send just an updated patch for just the base platform 
additions.  What I'm looking for is just changes/additions of the 
following files:

arch/ppc/syslib/mpc82xx_device.c
arch/ppc/syslib/mpc82xx_sys.c
include/asm-ppc/mpc8260.h
include/asm-ppc/ppc_sys.h

thanks

- kumar

On May 5, 2005, at 8:56 AM, Vitaly Bordug wrote:

>  Eugene Surovegin wrote:
> On Wed, May 04, 2005 at 06:35:16PM +0400, Vitaly Bordug wrote:
>
> This patch adds generic PlatformDevice support to the 82xx family.
> Only FCC's exist currently in the structure, as there is the driver
> which will utilize this.
>
>
> [snip]
>
>
> +#ifdef CONFIG_CPM2
> +       identify_ppc_sys_by_id(cpm2_immr->im_memctl.memc_immr << 16);
> +
> +       /* Set up the MAC addresses for the FECs
> +        */
> +       fec = ppc_sys_platform_devices[MPC82xx_FCC1].dev.platform_data;
> +       memcpy(fec->mac_addr,bi->bi_enetaddr,6);
> +
> +       fec = ppc_sys_platform_devices[MPC82xx_FCC2].dev.platform_data;
> +#ifdef CONFIG_ADS8272
> +       memcpy(fec->mac_addr,bi->bi_enet1addr,6);
> +#else
> +       memcpy(fec->mac_addr,bi->bi_enetaddr,6);
> +       fec->macaddr[5] ^= 1;
> +#endif
> +#endif
>
> What is this? Why does common file contain board specific ifdefs????
>
> [snip]
>
>
> +/* FCC1 Clock Source Configuration.  There are board specific.
> +   Can only choose from CLK9-12 */
> +#if defined(CONFIG_ADS8272)
> +#define F1_RXCLK       11
> +#define F1_TXCLK       10
> +#else
> +#define F1_RXCLK       12
> +#define F1_TXCLK       11
> +#endif
>
> Same thing. Why on earth you continue current 8xxx trend of putting
> board specific crap into common files?
>
>
> +
> +/* FCC2 Clock Source Configuration.  There are board specific.
> +   Can only choose from CLK13-16 */
> +#ifdef CONFIG_ADS8272
> +#define F2_RXCLK       15
> +#define F2_TXCLK       16
> +#else
> +#define F2_RXCLK       13
> +#define F2_TXCLK       14
> +#endif
>
> Ditto.
>
>
> +#ifdef CONFIG_ADS8272
> +#define PC_MDIO                0x00002000U
> +#define PC_MDCK                0x00001000U
> +#else
> +#define PC_MDIO                0x00000004U
> +#define PC_MDCK                0x00000020U
> +#endif
>
> Ditto.
>
>
> +                               .name   = "phyinterrupt",
> +                               .start  = SIU_INT_IRQ5,
> +                               .end    = SIU_INT_IRQ5,
> +                               .flags  = IORESOURCE_IRQ,
> +                       },
>
> Why is this here? PHY interrupt routing is _board_ specific.
>
>
>  I have fixed these yet, but I think it will be more reasonable to 
> update this together with respective driver which I'll work on 
> together with Pantelis.
>  Thank you for review.
>
>
> -- 
> Sincerely,
> Vitaly
>
> <ATT400050.txt>