MPC8272 runs application with segmentation fault
Nai-Hsien
dennis at loop.com.tw
Wed Jun 8 23:39:24 EST 2005
MessageAndrew,
I believe I already modify my u-boot to detect the processor.
If I statically link my program, I find that the program can run
on my MPC8272 platform properly, so I think maybe the problem
is caused by shared library. However, the same file system (of course,
same shared library) can run on my MPC8245 platform.
With the observation, I think my kernel is not handling shared library
properly. Is there any part of the kernel I should check?
I added some code in do_page_fault() to dump some information, shown
as below, when my program get problem.
PID=34(console): Trap=300, NIP=0x0ffc6d90, LR=0x0ffc6d20, VM: (start=0x30000000,
end=0x30017000, flags=0x00000875), addr=0x2e313056
Segmentation fault
Thank you
Dennis
----- Original Message -----
From: Andrew Williams
To: Nai-Hsien ; linuxppc-embedded at ozlabs.org
Sent: Tuesday, June 07, 2005 10:17 PM
Subject: RE: MPC8272 runs application with segmentation fault
Take a alook at the checkcpu() routine in /cpu/mpc8260/cpu.c .
Validate that your CPU is correctly being identified, and thus initialized.
We had identical symptoms with the 8270.
We added the following after the case for the PVR_8260_HIP7:
case PVR_8280a_HIP7:
case PVR_8280_HIP7:
k = 7;
printf (CPU_ID_STR " (HiP%d Rev %02x, Mask ", k, rev);
break;
include/asm-ppc/processor.h
#define PVR_8280_HIP7 0x80822013
#define PVR_8280a_HIP7 0x80822014
A.
-----Original Message-----
From: linuxppc-embedded-bounces at ozlabs.org [mailto:linuxppc-embedded-bounces at ozlabs.org] On Behalf Of Nai-Hsien
Sent: June 7, 2005 9:11 AM
To: linuxppc-embedded at ozlabs.org
Subject: MPC8272 runs application with segmentation fault
Dear experts,
I have two hardware boards, one uses MPC8245 and the other one uses MPC8272.
Initially, I use the MPC8245 board to port Linux 2.4.20 and write some applications.
I already do a lot of test on the MPC8245 board and all my application programs work
fine.
After this, I use the same kernel configuration and same file system that are being used
by the MPC8245 board to port the whole system to my MPC8272.
Now, I can boot the kernel and run busybox well. However, when
I run my application programs, I always get segmentation fault. Following is a strace
dump. Could anybody give me some idea?
Thank you
Dennis
====================================================
execve("sbin/console", ["sbin/console"], [/* 6 vars */]) = 0
uname({sys="Linux", node="6200_linux", ...}) = 0
brk(0) = 0x10059134
open("/etc/ld.so.preload", O_RDONLY) = -1 ENOENT (No such file or directory)
open("/etc/ld.so.cache", O_RDONLY) = -1 ENOENT (No such file or directory)
open("/lib/libncurses.so.5", O_RDONLY) = 3
read(3, "\177ELF\1\2\1\0\0\0\0\0\0\0\0\0\0\3\0\24\0\0\0\1\0\001"..., 1024) = 1024
fstat64(0x3, 0x7ffff098) = 0
mmap(0xff97000, 362628, PROT_READ|PROT_EXEC, MAP_PRIVATE, 3, 0) = 0xff97000
mprotect(0xffd4000, 112772, PROT_NONE) = 0
mmap(0xffd7000, 86016, PROT_READ|PROT_WRITE|PROT_EXEC, MAP_PRIVATE|MAP_FIXED, 3, 0x30000) = 0xffd7000
mmap(0xffec000, 14468, PROT_READ|PROT_WRITE|PROT_EXEC, MAP_PRIVATE|MAP_FIXED|MAP_ANONYMOUS, -1, 0) = 0xffec000
close(3) = 0
open("/lib/libdl.so.2", O_RDONLY) = 3
read(3, "\177ELF\1\2\1\0\0\0\0\0\0\0\0\0\0\3\0\24\0\0\0\1\0\0\34"..., 1024) = 1024
fstat64(0x3, 0x7ffff078) = 0
mmap(0xff74000, 74812, PROT_READ|PROT_EXEC, MAP_PRIVATE, 3, 0) = 0xff74000
mprotect(0xff77000, 62524, PROT_NONE) = 0
mmap(0xff84000, 12288, PROT_READ|PROT_WRITE|PROT_EXEC, MAP_PRIVATE|MAP_FIXED, 3, 0) = 0xff84000
close(3) = 0
open("/lib/libnsl.so.1", O_RDONLY) = 3
read(3, "\177ELF\1\2\1\0\0\0\0\0\0\0\0\0\0\3\0\24\0\0\0\1\0\0A\274"..., 1024) = 1024
fstat64(0x3, 0x7ffff058) = 0
mmap(NULL, 4096, PROT_READ|PROT_WRITE, MAP_PRIVATE|MAP_ANONYMOUS, -1, 0) = 0x30017000
mmap(0xff3e000, 152068, PROT_READ|PROT_EXEC, MAP_PRIVATE, 3, 0) = 0xff3e000
mprotect(0xff51000, 74244, PROT_NONE) = 0
mmap(0xff5e000, 12288, PROT_READ|PROT_WRITE|PROT_EXEC, MAP_PRIVATE|MAP_FIXED, 3, 0x10000) = 0xff5e000
mmap(0xff61000, 8708, PROT_READ|PROT_WRITE|PROT_EXEC, MAP_PRIVATE|MAP_FIXED|MAP_ANONYMOUS, -1, 0) = 0xff61000
close(3) = 0
open("/lib/libc.so.6", O_RDONLY) = 3
read(3, "\177ELF\1\2\1\0\0\0\0\0\0\0\0\0\0\3\0\24\0\0\0\1\0\1\322"..., 1024) = 1024
fstat64(0x3, 0x7ffff038) = 0
mmap(0xfddd000, 1379388, PROT_READ|PROT_EXEC, MAP_PRIVATE, 3, 0) = 0xfddd000
mprotect(0xff16000, 97340, PROT_NONE) = 0
mmap(0xff1d000, 61440, PROT_READ|PROT_WRITE|PROT_EXEC, MAP_PRIVATE|MAP_FIXED, 3, 0x130000) = 0xff1d000
mmap(0xff2c000, 7228, PROT_READ|PROT_WRITE|PROT_EXEC, MAP_PRIVATE|MAP_FIXED|MAP_ANONYMOUS, -1, 0) = 0xff2c000
close(3) = 0
brk(0) = 0x10059134
brk(0x1005a134) = 0x1005a134
brk(0x1005b000) = 0x1005b000
write(2, "before init_ncurses()\n", 22) = 22
write(2, "before initscr()\n", 17) = 17
access("/usr/share/terminfo/v/vt100", R_OK) = 0
open("/usr/share/terminfo/v/vt100", O_RDONLY) = 3
read(3, "\32\1,\0\25\0\7\0\16\1\3\2", 12) = 12
read(3, "vt100|vt100-am|dec vt100 (w/adva"..., 44) = 44
read(3, "\0\1\0\0\1\0\0\0\0\0\0\0\0\0\1\0\0\0\0\0\1", 21) = 21
read(3, "\0", 1) = 1
read(3, "P\0\10\0\30\0\377\377\377\377\377\377\3\0", 14) = 14
read(3, "\377\377\0\0\2\0\4\0\25\0\32\0&\0.\0\377\377\377\3777\0"..., 540) = 540
read(3, "\7\0\r\0\33[%i%p1%d;%p2%dr\0\33[3g\0\33[H\33[J"..., 515) = 515
read(3, "", 1) = 0
read(3, "", 10) = 0
close(3) = 0
-- SIGSEGV (Segmentation fault) @ 0 (0) ---
+++ killed by SIGSEGV +++
Segmentation fault
-------------- next part --------------
An HTML attachment was scrubbed...
URL: http://ozlabs.org/pipermail/linuxppc-embedded/attachments/20050608/1649cb1d/attachment.htm
More information about the Linuxppc-embedded
mailing list