[PATCH] ppc32 :Added PCI support for MPC83xx
Kumar Gala
kumar.gala at freescale.com
Tue Aug 30 14:27:39 EST 2005
Hmm, well the PCI spec seems to be clear on the fact that PCI
interrupts should be level sensitive.
- kumar
On Aug 29, 2005, at 10:02 PM, Li Tony-r64360 wrote:
> I think it is OK. The external interrupt can be edged. And it works
> well
> in my board.
>
> Tony Li
>
> -----Original Message-----
> From: Gala Kumar K.-galak
> Sent: Tuesday, August 30, 2005 1:43 AM
> To: Li Tony-r64360
> Cc: linuxppc-embedded; linux-kernel at vger.kernel.org; Gala Kumar
> K.-galak; Chu hanjin-r52514
> Subject: Re: [PATCH] ppc32 :Added PCI support for MPC83xx
>
> I noticed that you aren't updating the senses array in
> mpc834x_sys_init_IRQ for the PCI interrupt lines, is this correct?
> Should they not be IRQ_SENSE_LEVEL?
>
> Also, I've done a bit of cosmetic cleanup to the patch, take a look
> and
> let me know if it works. Once we close on the IRQ sense issue I will
> send this upstream.
>
> - kumar
>
> ---
>
> diff --git a/arch/ppc/Kconfig b/arch/ppc/Kconfig
> --- a/arch/ppc/Kconfig
> +++ b/arch/ppc/Kconfig
> @@ -713,6 +713,12 @@ config MPC834x_SYS
> help
> This option enables support for the MPC 834x SYS evaluation
> board.
>
> + Be aware that PCI buses can only function when SYS board is
> plugged on
> + PIB (Platform IO Board) board from Freescale which provide 3
> PCI slots.
> + Just like PC,the board level initalization is bootloader`s
> responsiblilty.
> + The PCI deponds on bootloader configurate board corretly.
> Refer to Freescale
> + to get more information about this.
> +
> endchoice
>
> config PQ2ADS
> @@ -1193,6 +1199,11 @@ config PCI
> config PCI_DOMAINS
> bool
> default PCI
> +
> +config MPC83xx_PCI2
> + bool " Supprt for 2nd PCI host controller"
> + depends on PCI && MPC834x
> + default y if MPC834x_SYS
>
> config PCI_QSPAN
> bool "QSpan PCI"
> diff --git a/arch/ppc/platforms/83xx/mpc834x_sys.c
> b/arch/ppc/platforms/83xx/mpc834x_sys.c
> --- a/arch/ppc/platforms/83xx/mpc834x_sys.c
> +++ b/arch/ppc/platforms/83xx/mpc834x_sys.c
> @@ -62,9 +62,29 @@ extern unsigned long total_memory; /* in
> unsigned char __res[sizeof (bd_t)];
>
> #ifdef CONFIG_PCI
> -#error "PCI is not supported"
> -/* NEED mpc83xx_map_irq & mpc83xx_exclude_device
> - see platforms/85xx/mpc85xx_ads_common.c */
> +int
> +mpc83xx_map_irq(struct pci_dev *dev, unsigned char idsel, unsigned
> char
>
> +pin) {
> + static char pci_irq_table[][4] =
> + /*
> + * PCI IDSEL/INTPIN->INTLINE
> + * A B C D
> + */
> + {
> + {PIRQA, PIRQB, PIRQC, PIRQD}, /* idsel 0x11 */
> + {PIRQC, PIRQD, PIRQA, PIRQB}, /* idsel 0x12 */
> + {PIRQD, PIRQA, PIRQB, PIRQC} /* idsel 0x13 */
> + };
> +
> + const long min_idsel = 0x11, max_idsel = 0x13, irqs_per_slot =
> 4;
> + return PCI_IRQ_TABLE_LOOKUP;
> +}
> +
> +int
> +mpc83xx_exclude_device(u_char bus, u_char devfn) {
> + return PCIBIOS_SUCCESSFUL;
> +}
> #endif /* CONFIG_PCI */
>
> /*
> **********************************************************************
> **
> @@ -88,7 +108,7 @@ mpc834x_sys_setup_arch(void)
>
> #ifdef CONFIG_PCI
> /* setup PCI host bridges */
> - mpc83xx_sys_setup_hose();
> + mpc83xx_setup_hose();
> #endif
> mpc83xx_early_serial_map();
>
> diff --git a/arch/ppc/platforms/83xx/mpc834x_sys.h
> b/arch/ppc/platforms/83xx/mpc834x_sys.h
> --- a/arch/ppc/platforms/83xx/mpc834x_sys.h
> +++ b/arch/ppc/platforms/83xx/mpc834x_sys.h
> @@ -26,7 +26,7 @@
> #define VIRT_IMMRBAR ((uint)0xfe000000)
>
> #define BCSR_PHYS_ADDR ((uint)0xf8000000)
> -#define BCSR_SIZE ((uint)(32 * 1024))
> +#define BCSR_SIZE ((uint)(128 * 1024))
>
> #define BCSR_MISC_REG2_OFF 0x07
> #define BCSR_MISC_REG2_PORESET 0x01
> @@ -34,23 +34,25 @@
> #define BCSR_MISC_REG3_OFF 0x08
> #define BCSR_MISC_REG3_CNFLOCK 0x80
>
> -#ifdef CONFIG_PCI
> -/* PCI interrupt controller */
> -#define PIRQA MPC83xx_IRQ_IRQ4
> -#define PIRQB MPC83xx_IRQ_IRQ5
> -#define PIRQC MPC83xx_IRQ_IRQ6
> -#define PIRQD MPC83xx_IRQ_IRQ7
> -
> -#define MPC834x_SYS_PCI1_LOWER_IO 0x00000000
> -#define MPC834x_SYS_PCI1_UPPER_IO 0x00ffffff
> -
> -#define MPC834x_SYS_PCI1_LOWER_MEM 0x80000000
> -#define MPC834x_SYS_PCI1_UPPER_MEM 0x9fffffff
> -
> -#define MPC834x_SYS_PCI1_IO_BASE 0xe2000000
> -#define MPC834x_SYS_PCI1_MEM_OFFSET 0x00000000
> -
> -#define MPC834x_SYS_PCI1_IO_SIZE 0x01000000
> -#endif /* CONFIG_PCI */
> +#define PIRQA MPC83xx_IRQ_EXT4
> +#define PIRQB MPC83xx_IRQ_EXT5
> +#define PIRQC MPC83xx_IRQ_EXT6
> +#define PIRQD MPC83xx_IRQ_EXT7
> +
> +#define MPC83xx_PCI1_LOWER_IO 0x00000000
> +#define MPC83xx_PCI1_UPPER_IO 0x00ffffff
> +#define MPC83xx_PCI1_LOWER_MEM 0x80000000
> +#define MPC83xx_PCI1_UPPER_MEM 0x9fffffff
> +#define MPC83xx_PCI1_IO_BASE 0xe2000000
> +#define MPC83xx_PCI1_MEM_OFFSET 0x00000000
> +#define MPC83xx_PCI1_IO_SIZE 0x01000000
> +
> +#define MPC83xx_PCI2_LOWER_IO 0x00000000
> +#define MPC83xx_PCI2_UPPER_IO 0x00ffffff
> +#define MPC83xx_PCI2_LOWER_MEM 0xa0000000
> +#define MPC83xx_PCI2_UPPER_MEM 0xbfffffff
> +#define MPC83xx_PCI2_IO_BASE 0xe3000000
> +#define MPC83xx_PCI2_MEM_OFFSET 0x00000000
> +#define MPC83xx_PCI2_IO_SIZE 0x01000000
>
> #endif /* __MACH_MPC83XX_SYS_H__ */
> diff --git a/arch/ppc/syslib/ppc83xx_pci.h
> b/arch/ppc/syslib/ppc83xx_pci.h new file mode 100644
> --- /dev/null
> +++ b/arch/ppc/syslib/ppc83xx_pci.h
> @@ -0,0 +1,151 @@
> +/* Created by Tony Li <tony.li at freescale.com>
> + * Copyright (c) 2005 freescale semiconductor
> + *
> + * This program is free software; you can redistribute it and/or
> +modify it
> + * under the terms of the GNU General Public License as
> published by
>
> +the
> + * Free Software Foundation; either version 2 of the License, or
> (at
> +your
> + * option) any later version.
> + *
> + * This program is distributed in the hope that it will be useful,
> but
> + * WITHOUT ANY WARRANTY; without even the implied warranty of
> + * MERCHANTABILITY or FITNESS FOR A PARTICULAR PURPOSE. See the GNU
> + * General Public License for more details.
> + *
> + * You should have received a copy of the GNU General Public License
> +along
> + * with this program; if not, write to the Free Software Foundation,
> +Inc.,
> + * 675 Mass Ave, Cambridge, MA 02139, USA.
> + */
> +
> +#ifndef __PPC_SYSLIB_PPC83XX_PCI_H
> +#define __PPC_SYSLIB_PPC83XX_PCI_H
> +
> +typedef struct immr_clk {
> + u32 spmr; /* system PLL mode Register */
> + u32 occr; /* output clock control Register */
> + u32 sccr; /* system clock control Register */
> + u8 res0[0xF4];
> +} immr_clk_t;
> +
> +/*
> + * Sequencer
> + */
> +typedef struct immr_ios {
> + u32 potar0;
> + u8 res0[4];
> + u32 pobar0;
> + u8 res1[4];
> + u32 pocmr0;
> + u8 res2[4];
> + u32 potar1;
> + u8 res3[4];
> + u32 pobar1;
> + u8 res4[4];
> + u32 pocmr1;
> + u8 res5[4];
> + u32 potar2;
> + u8 res6[4];
> + u32 pobar2;
> + u8 res7[4];
> + u32 pocmr2;
> + u8 res8[4];
> + u32 potar3;
> + u8 res9[4];
> + u32 pobar3;
> + u8 res10[4];
> + u32 pocmr3;
> + u8 res11[4];
> + u32 potar4;
> + u8 res12[4];
> + u32 pobar4;
> + u8 res13[4];
> + u32 pocmr4;
> + u8 res14[4];
> + u32 potar5;
> + u8 res15[4];
> + u32 pobar5;
> + u8 res16[4];
> + u32 pocmr5;
> + u8 res17[4];
> + u8 res18[0x60];
> + u32 pmcr;
> + u8 res19[4];
> + u32 dtcr;
> + u8 res20[4];
> +} immr_ios_t;
> +#define POTAR_TA_MASK 0x000fffff
> +#define POBAR_BA_MASK 0x000fffff
> +#define POCMR_EN 0x80000000
> +#define POCMR_IO 0x40000000 /* 0--memory space 1--I/O space */
> +#define POCMR_SE 0x20000000 /* streaming enable */
> +#define POCMR_DST 0x10000000 /* 0--PCI1 1--PCI2 */
> +#define POCMR_CM_MASK 0x000fffff
> +
> +/*
> + * PCI Controller Control and Status Registers */ typedef struct
> +immr_pcictrl {
> + u32 esr;
> + u32 ecdr;
> + u32 eer;
> + u32 eatcr;
> + u32 eacr;
> + u32 eeacr;
> + u32 edlcr;
> + u32 edhcr;
> + u32 gcr;
> + u32 ecr;
> + u32 gsr;
> + u8 res0[12];
> + u32 pitar2;
> + u8 res1[4];
> + u32 pibar2;
> + u32 piebar2;
> + u32 piwar2;
> + u8 res2[4];
> + u32 pitar1;
> + u8 res3[4];
> + u32 pibar1;
> + u32 piebar1;
> + u32 piwar1;
> + u8 res4[4];
> + u32 pitar0;
> + u8 res5[4];
> + u32 pibar0;
> + u8 res6[4];
> + u32 piwar0;
> + u8 res7[132];
> +} immr_pcictrl_t;
> +#define PITAR_TA_MASK 0x000fffff
> +#define PIBAR_MASK 0xffffffff
> +#define PIEBAR_EBA_MASK 0x000fffff
> +#define PIWAR_EN 0x80000000
> +#define PIWAR_PF 0x20000000
> +#define PIWAR_RTT_MASK 0x000f0000
> +#define PIWAR_RTT_NO_SNOOP 0x00040000
> +#define PIWAR_RTT_SNOOP 0x00050000
> +#define PIWAR_WTT_MASK 0x0000f000
> +#define PIWAR_WTT_NO_SNOOP 0x00004000
> +#define PIWAR_WTT_SNOOP 0x00005000
> +#define PIWAR_IWS_MASK 0x0000003F
> +#define PIWAR_IWS_4K 0x0000000B
> +#define PIWAR_IWS_8K 0x0000000C
> +#define PIWAR_IWS_16K 0x0000000D
> +#define PIWAR_IWS_32K 0x0000000E
> +#define PIWAR_IWS_64K 0x0000000F
> +#define PIWAR_IWS_128K 0x00000010
> +#define PIWAR_IWS_256K 0x00000011
> +#define PIWAR_IWS_512K 0x00000012
> +#define PIWAR_IWS_1M 0x00000013
> +#define PIWAR_IWS_2M 0x00000014
> +#define PIWAR_IWS_4M 0x00000015
> +#define PIWAR_IWS_8M 0x00000016
> +#define PIWAR_IWS_16M 0x00000017
> +#define PIWAR_IWS_32M 0x00000018
> +#define PIWAR_IWS_64M 0x00000019
> +#define PIWAR_IWS_128M 0x0000001A
> +#define PIWAR_IWS_256M 0x0000001B
> +#define PIWAR_IWS_512M 0x0000001C
> +#define PIWAR_IWS_1G 0x0000001D
> +#define PIWAR_IWS_2G 0x0000001E
> +
> +#endif /* __PPC_SYSLIB_PPC83XX_PCI_H */
> diff --git a/arch/ppc/syslib/ppc83xx_setup.c
> b/arch/ppc/syslib/ppc83xx_setup.c
> --- a/arch/ppc/syslib/ppc83xx_setup.c
> +++ b/arch/ppc/syslib/ppc83xx_setup.c
> @@ -11,6 +11,17 @@
> * under the terms of the GNU General Public License as
> published by
> the
> * Free Software Foundation; either version 2 of the License, or
> (at
> your
> * option) any later version.
> + *
> + * This program is distributed in the hope that it will be useful,
> but
> + * WITHOUT ANY WARRANTY; without even the implied warranty of
> + * MERCHANTABILITY or FITNESS FOR A PARTICULAR PURPOSE. See the GNU
> + * General Public License for more details.
> + *
> + * You should have received a copy of the GNU General Public License
> + along
> + * with this program; if not, write to the Free Software Foundation,
> + Inc.,
> + * 675 Mass Ave, Cambridge, MA 02139, USA.
> + *
> + * Added PCI support -- Tony Li <tony.li at freescale.com>
> */
>
> #include <linux/config.h>
> @@ -31,6 +42,10 @@
> #include <asm/delay.h>
>
> #include <syslib/ppc83xx_setup.h>
> +#if defined(CONFIG_PCI)
> +#include <asm/delay.h>
> +#include <syslib/ppc83xx_pci.h>
> +#endif
>
> phys_addr_t immrbar;
>
> @@ -162,4 +177,237 @@ mpc83xx_halt(void)
> for(;;);
> }
>
> -/* PCI SUPPORT DOES NOT EXIT, MODEL after ppc85xx_setup.c */
> +#if defined(CONFIG_PCI)
> +void __init
> +mpc83xx_setup_pci1(struct pci_controller *hose) {
> + u16 reg16;
> + volatile immr_pcictrl_t * pci_ctrl;
> + volatile immr_ios_t * ios;
> + bd_t *binfo = (bd_t *) __res;
> +
> + pci_ctrl = ioremap(binfo->bi_immr_base + 0x8500,
> sizeof(immr_pcictrl_t));
> + ios = ioremap(binfo->bi_immr_base + 0x8400, sizeof(immr_ios_t));
> +
> + /*
> + * Configure PCI Outbound Translation Windows
> + */
> + ios->potar0 = (MPC83xx_PCI1_LOWER_MEM >> 12) & POTAR_TA_MASK;
> + ios->pobar0 = (MPC83xx_PCI1_LOWER_MEM >> 12) & POBAR_BA_MASK;
> + ios->pocmr0 = POCMR_EN |
> + (((0xffffffff - (MPC83xx_PCI1_UPPER_MEM -
> + MPC83xx_PCI1_LOWER_MEM)) >> 12) &
> POCMR_CM_MASK);
> +
> + /* mapped to PCI1 IO space */
> + ios->potar1 = (MPC83xx_PCI1_LOWER_IO >> 12) & POTAR_TA_MASK;
> + ios->pobar1 = (MPC83xx_PCI1_IO_BASE >> 12) & POBAR_BA_MASK;
> + ios->pocmr1 = POCMR_EN | POCMR_IO |
> + (((0xffffffff - (MPC83xx_PCI1_UPPER_IO -
> + MPC83xx_PCI1_LOWER_IO)) >> 12) &
> POCMR_CM_MASK);
> +
> + /*
> + * Configure PCI Inbound Translation Windows
> + */
> + pci_ctrl->pitar1 = 0x0;
> + pci_ctrl->pibar1 = 0x0;
> + pci_ctrl->piebar1 = 0x0;
> + pci_ctrl->piwar1 = PIWAR_EN | PIWAR_PF | PIWAR_RTT_SNOOP |
> +PIWAR_WTT_SNOOP | PIWAR_IWS_2G;
> +
> + /*
> + * Release PCI RST signal
> + */
> + pci_ctrl->gcr = 0;
> + udelay(2000);
> + pci_ctrl->gcr = 1;
> + udelay(2000);
> +
> + reg16 = 0xff;
> + early_read_config_word(hose, hose->first_busno, 0, PCI_COMMAND,
> ®16);
> + reg16 |= PCI_COMMAND_SERR | PCI_COMMAND_MASTER |
> PCI_COMMAND_MEMORY;
> + early_write_config_word(hose, hose->first_busno, 0, PCI_COMMAND,
>
> +reg16);
> +
> + /*
> + * Clear non-reserved bits in status register.
> + */
> + early_write_config_word(hose, hose->first_busno, 0, PCI_STATUS,
> 0xffff);
> + early_write_config_byte(hose, hose->first_busno, 0,
> PCI_LATENCY_TIMER,
> +0x80);
> +
> + iounmap(pci_ctrl);
> + iounmap(ios);
> +}
> +
> +void __init
> +mpc83xx_setup_pci2(struct pci_controller *hose) {
> + u16 reg16;
> + volatile immr_pcictrl_t * pci_ctrl;
> + volatile immr_ios_t * ios;
> + bd_t *binfo = (bd_t *) __res;
> +
> + pci_ctrl = ioremap(binfo->bi_immr_base + 0x8600,
> sizeof(immr_pcictrl_t));
> + ios = ioremap(binfo->bi_immr_base + 0x8400, sizeof(immr_ios_t));
> +
> + /*
> + * Configure PCI Outbound Translation Windows
> + */
> + ios->potar3 = (MPC83xx_PCI2_LOWER_MEM >> 12) & POTAR_TA_MASK;
> + ios->pobar3 = (MPC83xx_PCI2_LOWER_MEM >> 12) & POBAR_BA_MASK;
> + ios->pocmr3 = POCMR_EN | POCMR_DST |
> + (((0xffffffff - (MPC83xx_PCI2_UPPER_MEM -
> + MPC83xx_PCI2_LOWER_MEM)) >> 12) &
> POCMR_CM_MASK);
> +
> + /* mapped to PCI2 IO space */
> + ios->potar4 = (MPC83xx_PCI2_LOWER_IO >> 12) & POTAR_TA_MASK;
> + ios->pobar4 = (MPC83xx_PCI2_IO_BASE >> 12) & POBAR_BA_MASK;
> + ios->pocmr4 = POCMR_EN | POCMR_DST | POCMR_IO |
> + (((0xffffffff - (MPC83xx_PCI2_UPPER_IO -
> + MPC83xx_PCI2_LOWER_IO)) >> 12) &
> POCMR_CM_MASK);
> +
> + /*
> + * Configure PCI Inbound Translation Windows
> + */
> + pci_ctrl->pitar1 = 0x0;
> + pci_ctrl->pibar1 = 0x0;
> + pci_ctrl->piebar1 = 0x0;
> + pci_ctrl->piwar1 = PIWAR_EN | PIWAR_PF | PIWAR_RTT_SNOOP |
> +PIWAR_WTT_SNOOP | PIWAR_IWS_2G;
> +
> + /*
> + * Release PCI RST signal
> + */
> + pci_ctrl->gcr = 0;
> + udelay(2000);
> + pci_ctrl->gcr = 1;
> + udelay(2000);
> +
> + reg16 = 0xff;
> + early_read_config_word(hose, hose->first_busno, 0, PCI_COMMAND,
> ®16);
> + reg16 |= PCI_COMMAND_SERR | PCI_COMMAND_MASTER |
> PCI_COMMAND_MEMORY;
> + early_write_config_word(hose, hose->first_busno, 0, PCI_COMMAND,
>
> +reg16);
> +
> + /*
> + * Clear non-reserved bits in status register.
> + */
> + early_write_config_word(hose, hose->first_busno, 0, PCI_STATUS,
> 0xffff);
> + early_write_config_byte(hose, hose->first_busno, 0,
> PCI_LATENCY_TIMER,
> +0x80);
> +
> + iounmap(pci_ctrl);
> + iounmap(ios);
> +}
> +
> +/*
> + * PCI buses can be enabled only if SYS board combinates with PIB
> + * (Platform IO Board) board which provide 3 PCI slots. There is 2
> PCI
> +buses
> + * and 3 PCI slots, so people must configure the routes between them
> +before
> + * enable PCI bus. This routes are under the control of PCA9555PW
> +device which
> + * can be accessed via I2C bus 2 and are configured by firmware.
> Refer
> +to
> + * Freescale to get more information about firmware configuration.
> + */
> +
> +extern int mpc83xx_exclude_device(u_char bus, u_char devfn);
> extern int
>
> +mpc83xx_map_irq(struct pci_dev *dev, unsigned char idsel,
> + unsigned char pin);
> +void __init
> +mpc83xx_setup_hose(void)
> +{
> + u32 val32;
> + volatile immr_clk_t * clk;
> + struct pci_controller * hose1;
> +#ifdef CONFIG_MPC83xx_PCI2
> + struct pci_controller * hose2;
> +#endif
> + bd_t * binfo = (bd_t *)__res;
> +
> + clk = ioremap(binfo->bi_immr_base + 0xA00,
> + sizeof(immr_clk_t));
> +
> + /*
> + * Configure PCI controller and PCI_CLK_OUTPUT both in 66M mode
> + */
> + val32 = clk->occr;
> + udelay(2000);
> + clk->occr = 0xff000000;
> + udelay(2000);
> +
> + iounmap(clk);
> +
> + hose1 = pcibios_alloc_controller();
> + if(!hose1)
> + return;
> +
> + ppc_md.pci_swizzle = common_swizzle;
> + ppc_md.pci_map_irq = mpc83xx_map_irq;
> +
> + hose1->bus_offset = 0;
> + hose1->first_busno = 0;
> + hose1->last_busno = 0xff;
> +
> + setup_indirect_pci(hose1, binfo->bi_immr_base +
> PCI1_CFG_ADDR_OFFSET,
> + binfo->bi_immr_base + PCI1_CFG_DATA_OFFSET);
> + hose1->set_cfg_type = 1;
> +
> + mpc83xx_setup_pci1(hose1);
> +
> + hose1->pci_mem_offset = MPC83xx_PCI1_MEM_OFFSET;
> + hose1->mem_space.start = MPC83xx_PCI1_LOWER_MEM;
> + hose1->mem_space.end = MPC83xx_PCI1_UPPER_MEM;
> +
> + hose1->io_base_phys = MPC83xx_PCI1_IO_BASE;
> + hose1->io_space.start = MPC83xx_PCI1_LOWER_IO;
> + hose1->io_space.end = MPC83xx_PCI1_UPPER_IO; #ifdef
> +CONFIG_MPC83xx_PCI2
> + isa_io_base = (unsigned long)ioremap(MPC83xx_PCI1_IO_BASE,
> + MPC83xx_PCI1_IO_SIZE + MPC83xx_PCI2_IO_SIZE);
> #else
> + isa_io_base = (unsigned long)ioremap(MPC83xx_PCI1_IO_BASE,
> + MPC83xx_PCI1_IO_SIZE);
> +#endif /* CONFIG_MPC83xx_PCI2 */
> + hose1->io_base_virt = (void *)isa_io_base;
> + /* setup resources */
> + pci_init_resource(&hose1->io_resource,
> + MPC83xx_PCI1_LOWER_IO,
> + MPC83xx_PCI1_UPPER_IO,
> + IORESOURCE_IO, "PCI host bridge 1");
> + pci_init_resource(&hose1->mem_resources[0],
> + MPC83xx_PCI1_LOWER_MEM,
> + MPC83xx_PCI1_UPPER_MEM,
> + IORESOURCE_MEM, "PCI host bridge 1");
> +
> + ppc_md.pci_exclude_device = mpc83xx_exclude_device;
> + hose1->last_busno = pciauto_bus_scan(hose1, hose1->first_busno);
> +
> +#ifdef CONFIG_MPC83xx_PCI2
> + hose2 = pcibios_alloc_controller();
> + if(!hose2)
> + return;
> +
> + hose2->bus_offset = hose1->last_busno + 1;
> + hose2->first_busno = hose1->last_busno + 1;
> + hose2->last_busno = 0xff;
> + setup_indirect_pci(hose2, binfo->bi_immr_base +
> PCI2_CFG_ADDR_OFFSET,
> + binfo->bi_immr_base + PCI2_CFG_DATA_OFFSET);
> + hose2->set_cfg_type = 1;
> +
> + mpc83xx_setup_pci2(hose2);
> +
> + hose2->pci_mem_offset = MPC83xx_PCI2_MEM_OFFSET;
> + hose2->mem_space.start = MPC83xx_PCI2_LOWER_MEM;
> + hose2->mem_space.end = MPC83xx_PCI2_UPPER_MEM;
> +
> + hose2->io_base_phys = MPC83xx_PCI2_IO_BASE;
> + hose2->io_space.start = MPC83xx_PCI2_LOWER_IO;
> + hose2->io_space.end = MPC83xx_PCI2_UPPER_IO;
> + hose2->io_base_virt = (void *)(isa_io_base +
> MPC83xx_PCI1_IO_SIZE);
> + /* setup resources */
> + pci_init_resource(&hose2->io_resource,
> + MPC83xx_PCI2_LOWER_IO,
> + MPC83xx_PCI2_UPPER_IO,
> + IORESOURCE_IO, "PCI host bridge 2");
> + pci_init_resource(&hose2->mem_resources[0],
> + MPC83xx_PCI2_LOWER_MEM,
> + MPC83xx_PCI2_UPPER_MEM,
> + IORESOURCE_MEM, "PCI host bridge 2");
> +
> + hose2->last_busno = pciauto_bus_scan(hose2, hose2->first_busno);
>
> +#endif /* CONFIG_MPC83xx_PCI2 */ } #endif /*CONFIG_PCI*/
> diff --git a/arch/ppc/syslib/ppc83xx_setup.h
> b/arch/ppc/syslib/ppc83xx_setup.h
> --- a/arch/ppc/syslib/ppc83xx_setup.h
> +++ b/arch/ppc/syslib/ppc83xx_setup.h
> @@ -12,6 +12,14 @@
> * Free Software Foundation; either version 2 of the License, or
> (at
> your
> * option) any later version.
> *
> + * This program is distributed in the hope that it will be useful,
> but
> + * WITHOUT ANY WARRANTY; without even the implied warranty of
> + * MERCHANTABILITY or FITNESS FOR A PARTICULAR PURPOSE. See the GNU
> + * General Public License for more details.
> + *
> + * You should have received a copy of the GNU General Public License
> + along
> + * with this program; if not, write to the Free Software Foundation,
> + Inc.,
> + * 675 Mass Ave, Cambridge, MA 02139, USA.
> */
>
> #ifndef __PPC_SYSLIB_PPC83XX_SETUP_H
> @@ -19,7 +27,6 @@
>
> #include <linux/config.h>
> #include <linux/init.h>
> -#include <asm/ppcboot.h>
>
> extern unsigned long mpc83xx_find_end_of_memory(void) __init; extern
> long mpc83xx_time_init(void) __init; @@ -31,13 +38,11 @@ extern void
> mpc83xx_halt(void); extern void mpc83xx_setup_hose(void) __init;
>
> /* PCI config */
> -#if 0
> -#define PCI1_CFG_ADDR_OFFSET (FIXME)
> -#define PCI1_CFG_DATA_OFFSET (FIXME)
> +#define PCI1_CFG_ADDR_OFFSET (0x8300)
> +#define PCI1_CFG_DATA_OFFSET (0x8304)
>
> -#define PCI2_CFG_ADDR_OFFSET (FIXME)
> -#define PCI2_CFG_DATA_OFFSET (FIXME)
> -#endif
> +#define PCI2_CFG_ADDR_OFFSET (0x8380)
> +#define PCI2_CFG_DATA_OFFSET (0x8384)
>
> /* Serial Config */
> #ifdef CONFIG_SERIAL_MANY_PORTS
>
More information about the Linuxppc-embedded
mailing list