pci_enable_device fails on MPC8541

[Kumar Gala]

It would be extremely helpful to get the output from the work MPC8540  
for lspci and cat /proc/pci.

Also, I forget if 2.6.11 has CDS VIA support, but if it does you can  
try disabling it by commenting out the calls to:
mpc85xx_cds_enable_via() & mpc85xx_cds_fixup_via() in arch/ppc/syslib/ 
ppc85xx_setup.c and see what happens.

- k

On Aug 10, 2005, at 10:58 AM, Bizhan Gholikhamseh \\((bgholikh\\))  
wrote:

>  <<pci_boot.pdf>> Kumar,
> We do not support or care about VIA IDE controller. I have enabled the
> DEBUG flag and attached the debug messages during boot. This is for
> 8541E.
> Regards,
> Bizhan
>
> -----Original Message-----
> From: Kumar Gala [mailto:kumar.gala at freescale.com]
> Sent: Tuesday, August 09, 2005 4:11 PM
> To: Bizhan Gholikhamseh (bgholikh)
> Cc: linuxppc-embedded at ozlabs.org
> Subject: Re: pci_enable_device fails on MPC8541
>
> Do you need support for the VIA IDE controller?  I'm not sure if  
> that is
> causing you issues.
>
> Also, can you try enabling DEBUG in arch/ppc/kernel/pci.c and send a
> boot log.  I'm trying to figure out what is causing the resource
> conflict.  It appears that the memory resource is reasonable, but  
> there
> could be possible conflict on the IO resource side.
>
> Also, if you can send logs of the same thing from the working 8540 ADS
> that would be helpful.
>
> - kumar
>
> On Aug 9, 2005, at 12:18 PM, Bizhan Gholikhamseh \(((bgholikh\)))  
> wrote:
>
>
>> Hi Kumar,
>> I am using Linux 2.6.11, u-boot 1.1.2.
>> I see failure in pci_enable_device with message:
>> "PCI: Device 0000:02:01.0 not available because of resource
>> collisions"
>>
>> I have attached three files:
>> lspci_output.txt: out put of the "lspci -v"
>> proc_pci.txt: output of the "cat /proc/pci"
>> u-boot.txt: output of the "pci command at u-boot"
>>
>> Any help greatly appreciated,
>> Bizhan
>> -----Original Message-----
>> From: Kumar Gala [mailto:kumar.gala at freescale.com]
>> Sent: Monday, August 08, 2005 1:34 PM
>> To: Bizhan Gholikhamseh (bgholikh)
>> Cc: linuxppc-embedded at ozlabs.org
>> Subject: Re: pci_enable_device fails on MPC8541
>>
>> Bizhan,
>>
>> A few questions:
>>
>> 1. what kernel version are you using on these boards:
>> 2. can you do an lspci -v on the boards
>>
>> - kumar
>>
>> On Aug 8, 2005, at 1:12 PM, Bizhan Gholikhamseh \(((bgholikh\)))
>> wrote:
>>
>>
>>
>>> Hi All,
>>> I am using two evaluation board from freescale, 8540ADS and MPC8541.
>>> The same PCI driver is being compiled and loaded on both platforms.
>>> The same PCI driver (developed by me) for DSP board compiled and
>>> loaded on both platforms.
>>>
>>> When I type: "insmod C6415.ko" on 8541 board, I get the following
>>> error:
>>> "PCI: Device 0000:02:01.0 not available because of resource
>>> collisions"
>>> This messages is because of the execution of the generic PCI Linux
>>> command:
>>> "pci_enable_device(pdev)"
>>> The same API has no problem on 8540ADS.
>>>
>>>
>>>
>>>
>>>> From UBOOT I can see my device is on bus 3:
>>>>
>>>>
>>>>
>>> => pci 3
>>> Scanning PCI devices on bus 3
>>> BusDev FUN    VendorID    DeviceID    Device Class    Sub-Class
>>> -------------------------------------------------------------------- 
>>> -
>>>
>
>
>>> -
>>> --
>>> --------------------
>>> 03.01.00            0x104c    0xa106        .........
>>>
>>> Any idea why the insmod fails on one board and not on the other one?
>>>
>>> Many thanks in advance,
>>> Bizhan
>>>
>>> <ATT2118305.txt>
>>>
>>>
>>> <lspci_output.txt>
>>> <proc_pci.txt>
>>> <u-boot.txt>
>>>
>>
>>
>> <pci_boot.txt>
>> <pci_boot.pdf>
>