[PATCH 2.6.12-rc2] Freescale 8272ADS PCI bridge support to the stock linux-2.5 (updated)
Kumar Gala
galak at freescale.com
Thu Apr 21 06:56:00 EST 2005
On Wed, 13 Apr 2005, Vitaly Bordug wrote:
Finally, had some time to really look at this patch, comments are inline.
Look for (galak). A few high level comments:
Can we fold pq2ads_setup_hose into pq2ads_setup_pci? Also, is there
anything to be done to unify pq2ads_setup_pci & m8260_setup_pci..
> Kumar,
> This patch adds support for the MPC8272ADS PCI bridge.
>
> The previous one is cleaned up after the final review.
>
> Signed-off-by: Vitaly Bordug <vbordug at ru.mvista.com>
===== arch/ppc/Kconfig 1.109 vs edited =====
--- 1.109/arch/ppc/Kconfig 2005-04-04 07:03:47 +04:00
+++ edited/arch/ppc/Kconfig 2005-04-12 16:47:48 +04:00
@@ -1123,7 +1123,7 @@
config PCI_8260
bool
- depends on PCI && 8260 && !8272
+ depends on PCI && 8260
default y
config 8260_PCI9
===== arch/ppc/platforms/pq2ads.h 1.3 vs edited =====
--- 1.3/arch/ppc/platforms/pq2ads.h 2005-01-16 01:01:51 +03:00
+++ edited/arch/ppc/platforms/pq2ads.h 2005-04-13 20:38:43 +04:00
@@ -49,10 +49,10 @@
/* PCI interrupt controller */
#define PCI_INT_STAT_REG 0xF8200000
#define PCI_INT_MASK_REG 0xF8200004
-#define PIRQA (NR_SIU_INTS + 0)
-#define PIRQB (NR_SIU_INTS + 1)
-#define PIRQC (NR_SIU_INTS + 2)
-#define PIRQD (NR_SIU_INTS + 3)
+#define PIRQA (NR_CPM_INTS + 0)
+#define PIRQB (NR_CPM_INTS + 1)
+#define PIRQC (NR_CPM_INTS + 2)
+#define PIRQD (NR_CPM_INTS + 3)
/*
* PCI memory map definitions for MPC8266ADS-PCI.
@@ -71,6 +71,7 @@
/* window for a PCI master to access MPC8266 memory */
#define PCI_SLV_MEM_LOCAL 0x00000000 /* Local base */
#define PCI_SLV_MEM_BUS 0x00000000 /* PCI base */
+#define PCI_SLV_MEM_SIZE 0x10000000 /* 256 Mb */
/* window for the processor to access PCI memory with prefetching */
#define PCI_MSTR_MEM_LOCAL 0x80000000 /* Local base */
@@ -83,9 +84,75 @@
#define PCI_MSTR_MEMIO_SIZE 0x20000000 /* 512MB */
/* window for the processor to access PCI I/O */
+#if !defined(CONFIG_ADS8272) && !defined(CONFIG_PQ2FADS)
+
#define PCI_MSTR_IO_LOCAL 0xF4000000 /* Local base */
#define PCI_MSTR_IO_BUS 0x00000000 /* PCI base */
#define PCI_MSTR_IO_SIZE 0x04000000 /* 64MB */
+
+#else /* CONFIG_ADS8272 or CONFIG_PQ2FADS */
+
+#define PCI_MSTR_IO_LOCAL 0xF6000000 /* Local base */
(galak -- white space versus tabs, use tabs)
+#define PCI_MSTR_IO_BUS 0x00000000 /* PCI base */
+#define PCI_MSTR_IO_SIZE 0x02000000 /* 64MB */
+
(galak -- the defn of SIUMCR & SCCR probably belong in
include/asm-ppc/cpm2.h)
+/*-----------------------------------------------------------------------
+ * SIUMCR - SIU Module Configuration Register 4-31
+ */
+#define SIUMCR_BBD 0x80000000 /* Bus Busy Disable */
+#define SIUMCR_ESE 0x40000000 /* External Snoop Enable */
+#define SIUMCR_PBSE 0x20000000 /* Parity Byte Select Enable */
+#define SIUMCR_CDIS 0x10000000 /* Core Disable */
+#define SIUMCR_DPPC00 0x00000000 /* Data Parity Pins Configuration*/
+#define SIUMCR_DPPC01 0x04000000 /* - " - */
+#define SIUMCR_DPPC10 0x08000000 /* - " - */
+#define SIUMCR_DPPC11 0x0c000000 /* - " - */
+#define SIUMCR_L2CPC00 0x00000000 /* L2 Cache Pins Configuration */
+#define SIUMCR_L2CPC01 0x01000000 /* - " - */
+#define SIUMCR_L2CPC10 0x02000000 /* - " - */
+#define SIUMCR_L2CPC11 0x03000000 /* - " - */
+#define SIUMCR_LBPC00 0x00000000 /* Local Bus Pins Configuration */
+#define SIUMCR_LBPC01 0x00400000 /* - " - */
+#define SIUMCR_LBPC10 0x00800000 /* - " - */
+#define SIUMCR_LBPC11 0x00c00000 /* - " - */
+#define SIUMCR_APPC00 0x00000000 /* Address Parity Pins Configuration*/
+#define SIUMCR_APPC01 0x00100000 /* - " - */
+#define SIUMCR_APPC10 0x00200000 /* - " - */
+#define SIUMCR_APPC11 0x00300000 /* - " - */
+#define SIUMCR_CS10PC00 0x00000000 /* CS10 Pin Configuration */
+#define SIUMCR_CS10PC01 0x00040000 /* - " - */
+#define SIUMCR_CS10PC10 0x00080000 /* - " - */
+#define SIUMCR_CS10PC11 0x000c0000 /* - " - */
+#define SIUMCR_BCTLC00 0x00000000 /* Buffer Control Configuration */
+#define SIUMCR_BCTLC01 0x00010000 /* - " - */
+#define SIUMCR_BCTLC10 0x00020000 /* - " - */
+#define SIUMCR_BCTLC11 0x00030000 /* - " - */
+#define SIUMCR_MMR00 0x00000000 /* Mask Masters Requests */
+#define SIUMCR_MMR01 0x00004000 /* - " - */
+#define SIUMCR_MMR10 0x00008000 /* - " - */
+#define SIUMCR_MMR11 0x0000c000 /* - " - */
+#define SIUMCR_LPBSE 0x00002000 /* LocalBus Parity Byte Select Enable*/
+
+/*-----------------------------------------------------------------------
+ * SCCR - System Clock Control Register 9-8
+ */
+#define SCCR_PCI_MODE 0x00000100 /* PCI Mode */
+#define SCCR_PCI_MODCK 0x00000080 /* Value of PCI_MODCK pin */
+#define SCCR_PCIDF_MSK 0x00000078 /* PCI division factor */
+#define SCCR_PCIDF_SHIFT 3
+
+#endif
+
+#if defined(CONFIG_ADS8272)
+#define PCI_INT_TO_SIU SIU_INT_IRQ2
+#elif defined(CONFIG_PQ2FADS)
+#define PCI_INT_TO_SIU SIU_INT_IRQ6
+#else
+#warning PCI Bridge will be without interrupts support
+#endif
+
+#define POTA_ADDR_SHIFT 12
+#define PITA_ADDR_SHIFT 12
#define _IO_BASE PCI_MSTR_IO_LOCAL
#define _ISA_MEM_BASE PCI_MSTR_MEMIO_LOCAL
===== arch/ppc/syslib/Makefile 1.51 vs edited =====
--- 1.51/arch/ppc/syslib/Makefile 2005-03-31 14:59:04 +04:00
+++ edited/arch/ppc/syslib/Makefile 2005-04-12 16:47:50 +04:00
@@ -82,6 +82,9 @@
todc_time.o
obj-$(CONFIG_8260) += m8260_setup.o
obj-$(CONFIG_PCI_8260) += m8260_pci.o indirect_pci.o
+ifeq ($(CONFIG_ADS8272),y)
+obj-$(CONFIG_PCI) += pci_auto.o
+endif
obj-$(CONFIG_8260_PCI9) += m8260_pci_erratum9.o
obj-$(CONFIG_CPM2) += cpm2_common.o cpm2_pic.o
ifeq ($(CONFIG_PPC_GEN550),y)
===== arch/ppc/syslib/m8260_pci.c 1.2 vs edited =====
--- 1.2/arch/ppc/syslib/m8260_pci.c 2004-06-17 16:57:15 +04:00
+++ edited/arch/ppc/syslib/m8260_pci.c 2005-04-13 20:38:02 +04:00
@@ -1,4 +1,7 @@
(galak -- add your info after wolfgang & rhat)
/*
+ * 2005 (c) MontaVista Software, Inc.
+ * Vitaly Bordug <vbordug at ru.mvista.com>
+ *
* (C) Copyright 2003
* Wolfgang Denk, DENX Software Engineering, wd at denx.de.
*
@@ -28,6 +31,8 @@
#include <linux/pci.h>
#include <linux/slab.h>
#include <linux/delay.h>
+#include <linux/irq.h>
+#include <linux/interrupt.h>
#include <asm/byteorder.h>
#include <asm/io.h>
@@ -38,12 +43,144 @@
#include <asm/immap_cpm2.h>
#include <asm/mpc8260.h>
+#if !defined(CONFIG_ADS8272) && !defined(CONFIG_PQ2FADS)
#include "m8260_pci.h"
+#endif
+
+/*
+ * Interrupt routing
+ */
+
+static inline int
+pq2pci_map_irq(struct pci_dev *dev, unsigned char idsel, unsigned char pin)
+{
+ static char pci_irq_table[][4] =
+ /*
+ * PCI IDSEL/INTPIN->INTLINE
+ * A B C D
+ */
+ {
+ { PIRQA, PIRQB, PIRQC, PIRQD }, /* IDSEL 22 - PCI slot 0 */
+ { PIRQD, PIRQA, PIRQB, PIRQC }, /* IDSEL 23 - PCI slot 1 */
+ { PIRQC, PIRQD, PIRQA, PIRQB }, /* IDSEL 24 - PCI slot 2 */
+ };
+
+ const long min_idsel = 22, max_idsel = 24, irqs_per_slot = 4;
+ return PCI_IRQ_TABLE_LOOKUP;
+}
+
+static void
+pq2pci_mask_irq(unsigned int irq)
+{
+ int bit = irq - NR_CPM_INTS;
+
+ *(volatile unsigned long *) PCI_INT_MASK_REG |= (1 << (31 - bit));
+ return;
+}
+
+static void
+pq2pci_unmask_irq(unsigned int irq)
+{
+ int bit = irq - NR_CPM_INTS;
+
+ *(volatile unsigned long *) PCI_INT_MASK_REG &= ~(1 << (31 - bit));
+ return;
+}
+
+static void
+pq2pci_mask_and_ack(unsigned int irq)
+{
+ int bit = irq - NR_CPM_INTS;
+
+ *(volatile unsigned long *) PCI_INT_MASK_REG |= (1 << (31 - bit));
+ return;
+}
+
+static void
+pq2pci_end_irq(unsigned int irq)
+{
+ int bit = irq - NR_CPM_INTS;
+
+ *(volatile unsigned long *) PCI_INT_MASK_REG &= ~(1 << (31 - bit));
+ return;
+}
+
+struct hw_interrupt_type pq2pci_ic = {
+ "PQ2 PCI",
+ NULL,
+ NULL,
+ pq2pci_unmask_irq,
+ pq2pci_mask_irq,
+ pq2pci_mask_and_ack,
+ pq2pci_end_irq,
+ 0
+};
+
+static irqreturn_t
+pq2pci_irq_demux(int irq, void *dev_id, struct pt_regs *regs)
+{
+ unsigned long stat, mask, pend;
+ int bit;
+
+ for(;;) {
+ stat = *(volatile unsigned long *) PCI_INT_STAT_REG;
+ mask = *(volatile unsigned long *) PCI_INT_MASK_REG;
+ pend = stat & ~mask & 0xf0000000;
+ if (!pend)
+ break;
+ for (bit = 0; pend != 0; ++bit, pend <<= 1) {
+ if (pend & 0x80000000)
+ __do_IRQ(NR_CPM_INTS + bit, regs);
+ }
+ }
+
+ return IRQ_HANDLED;
+}
+
+static struct irqaction pq2pci_irqaction = {
+ .handler = pq2pci_irq_demux,
+ .flags = SA_INTERRUPT,
+ .mask = CPU_MASK_NONE,
+ .name = "PQ2 PCI cascade",
+};
+
+
+void
+pq2pci_init_irq(void)
+{
+ int irq;
+ volatile cpm2_map_t *immap = cpm2_immr;
+#ifdef CONFIG_ADS8272
+ /* configure chip select for PCI interrupt controller */
+ immap->im_memctl.memc_br3 = PCI_INT_STAT_REG | 0x00001801;
+ immap->im_memctl.memc_or3 = 0xffff8010;
+#endif
+ for (irq = NR_CPM_INTS; irq < NR_CPM_INTS + 4; irq++)
+ irq_desc[irq].handler = &pq2pci_ic;
+
+ /* make PCI IRQ level sensitive */
+ immap->im_intctl.ic_siexr &=
+ ~(1 << (14 - (PCI_INT_TO_SIU - SIU_INT_IRQ1)));
+
+ /* mask all PCI interrupts */
+ *(volatile unsigned long *) PCI_INT_MASK_REG |= 0xfff00000;
+
+ /* install the demultiplexer for the PCI cascade interrupt */
+ setup_irq(PCI_INT_TO_SIU, &pq2pci_irqaction);
+ return;
+}
+
+static int
+pq2pci_exclude_device(u_char bus, u_char devfn)
+{
+ return PCIBIOS_SUCCESSFUL;
+}
/* PCI bus configuration registers.
*/
+#if !defined(CONFIG_ADS8272) && !defined(CONFIG_PQ2FADS)
static void __init m8260_setup_pci(struct pci_controller *hose)
{
volatile cpm2_map_t *immap = cpm2_immr;
@@ -146,10 +283,148 @@
tempShort | PCI_COMMAND_MASTER | PCI_COMMAND_MEMORY);
}
-void __init m8260_find_bridges(void)
+#else /* setup hardware for 8272ADS and PQ2FADS */
+
+static void
+pq2ads_setup_pci(struct pci_controller *hose)
+{
+ __u32 val;
+ volatile cpm2_map_t *immap = cpm2_immr;
+ bd_t* binfo = (bd_t*) __res;
+ u32 sccr = immap->im_clkrst.car_sccr;
+ uint pci_div,freq,time;
+ /* PCI int lowest prio */
+ /* Each 4 bits is a device bus request and the MS 4bits
+ is highest priority */
+ /* Bus 4bit value
+ --- ----------
+ CPM high 0b0000
+ CPM middle 0b0001
+ CPM low 0b0010
+ PCI reguest 0b0011
+ Reserved 0b0100
+ Reserved 0b0101
+ Internal Core 0b0110
+ External Master 1 0b0111
+ External Master 2 0b1000
+ External Master 3 0b1001
+ The rest are reserved
+ */
+ immap->im_siu_conf.siu_82xx.sc_ppc_alrh = 0x61207893;
+ /* park bus on core */
+ immap->im_siu_conf.siu_82xx.sc_ppc_acr = PPC_ACR_BUS_PARK_CORE;
+ /*
+ * Set up master windows that allow the CPU to access PCI space. These
+ * windows are set up using the two SIU PCIBR registers.
+ */
+
+ immap->im_memctl.memc_pcimsk0 = ~(PCI_MSTR_IO_SIZE - 1U);
+ immap->im_memctl.memc_pcibr0 = PCI_MSTR_IO_LOCAL | PCIBR_ENABLE;
+
+ immap->im_memctl.memc_pcimsk1 = ~(PCI_MSTR_MEM_SIZE + PCI_MSTR_MEMIO_SIZE - 1U);
+ immap->im_memctl.memc_pcibr1 = PCI_MSTR_MEM_LOCAL | PCIBR_ENABLE;
+#ifdef CONFIG_ADS8272
+ immap->im_siu_conf.siu_82xx.sc_siumcr = (immap->im_siu_conf.siu_82xx.sc_siumcr &
(galak typically we do this a foo & ~(A | B | C | D )
+ ~SIUMCR_BBD &
+ ~SIUMCR_ESE &
+ ~SIUMCR_PBSE &
+ ~SIUMCR_CDIS &
+ ~SIUMCR_DPPC11 &
+ ~SIUMCR_L2CPC11 &
+ ~SIUMCR_LBPC11 &
+ ~SIUMCR_APPC11 &
+ ~SIUMCR_CS10PC11 &
+ ~SIUMCR_BCTLC11 &
+ ~SIUMCR_MMR11)
+ | SIUMCR_DPPC11 | SIUMCR_L2CPC01 | SIUMCR_LBPC00
+ | SIUMCR_APPC10 | SIUMCR_CS10PC00 | SIUMCR_BCTLC00 | SIUMCR_MMR11;
+#elif defined CONFIG_PQ2FADS
+ /*
+ * Setting required to enable IRQ1-IRQ7 (SIUMCR [DPPC]),
+ * and local bus for PCI (SIUMCR [LBPC]).
+ */
+ immap->im_siu_conf.siu_82xx.sc_siumcr = (immap->im_siu_conf.sc_siumcr &
+ ~SIUMCR_LBPC11 &
+ ~SIUMCR_CS10PC11 &
+ ~SIUMCR_LBPC11) |
+ SIUMCR_LBPC01 | SIUMCR_CS10PC01 | SIUMCR_APPC10;
+#endif
+ /* Enable PCI */
+ immap->im_pci.pci_gcr = cpu_to_le32(PCIGCR_PCI_BUS_EN);
+
+ pci_div = ( (sccr & SCCR_PCI_MODCK) ? 2 : 1) *
+ ( ( (sccr & SCCR_PCIDF_MSK) >> SCCR_PCIDF_SHIFT) + 1);
+ freq = (uint)((2*binfo->bi_cpmfreq)/(pci_div));
+ time = (int)666666/freq;
+ /* due to PCI Local Bus spec, some devices needs to wait such a long
+ time after RST deassertion. More specifically, 0.508s for 66MHz & twice more for 33 */
+ printk("%s: The PCI bus is %d Mhz.\nWaiting %s after deasserting RST...\n",__FILE__,freq,
+ (time==1) ? "0.5 seconds":"1 second" );
+
+ {
+ int i;
+ for(i=0;i<(500*time);i++)
+ udelay(1000);
+ }
+
+ /* setup ATU registers */
+ immap->im_pci.pci_pocmr0 = cpu_to_le32(POCMR_ENABLE | POCMR_PCI_IO |
+ ((~(PCI_MSTR_IO_SIZE - 1U)) >> POTA_ADDR_SHIFT));
+ immap->im_pci.pci_potar0 = cpu_to_le32(PCI_MSTR_IO_BUS >> POTA_ADDR_SHIFT);
+ immap->im_pci.pci_pobar0 = cpu_to_le32(PCI_MSTR_IO_LOCAL >> POTA_ADDR_SHIFT);
+
+ /* Set-up non-prefetchable window */
+ immap->im_pci.pci_pocmr1 = cpu_to_le32(POCMR_ENABLE | ((~(PCI_MSTR_MEMIO_SIZE-1U)) >> POTA_ADDR_SHIFT));
+ immap->im_pci.pci_potar1 = cpu_to_le32(PCI_MSTR_MEMIO_BUS >> POTA_ADDR_SHIFT);
+ immap->im_pci.pci_pobar1 = cpu_to_le32(PCI_MSTR_MEMIO_LOCAL >> POTA_ADDR_SHIFT);
+
+ /* Set-up prefetchable window */
+ immap->im_pci.pci_pocmr2 = cpu_to_le32(POCMR_ENABLE |POCMR_PREFETCH_EN |
+ (~(PCI_MSTR_MEM_SIZE-1U) >> POTA_ADDR_SHIFT));
+ immap->im_pci.pci_potar2 = cpu_to_le32((PCI_MSTR_MEM_BUS) >> POTA_ADDR_SHIFT);
+ immap->im_pci.pci_pobar2 = cpu_to_le32((PCI_MSTR_MEM_LOCAL) >> POTA_ADDR_SHIFT);
+
+ /* Inbound transactions from PCI memory space */
+ immap->im_pci.pci_picmr0 = cpu_to_le32(PICMR_ENABLE | PICMR_PREFETCH_EN |
+ ((~(PCI_SLV_MEM_SIZE-1U)) >> PITA_ADDR_SHIFT));
+ immap->im_pci.pci_pibar0 = cpu_to_le32(PCI_SLV_MEM_BUS >> PITA_ADDR_SHIFT);
+ immap->im_pci.pci_pitar0 = cpu_to_le32(PCI_SLV_MEM_LOCAL>> PITA_ADDR_SHIFT);
+
+#if defined CONFIG_ADS8272
+ /* PCI int highest prio */
+ immap->im_siu_conf.siu_82xx.sc_ppc_alrh = 0x01236745;
+#elif defined CONFIG_PQ2FADS
+ immap->im_siu_conf.siu_82xx.sc_ppc_alrh = 0x03124567;
+#endif
+ /* park bus on PCI */
+ immap->im_siu_conf.siu_82xx.sc_ppc_acr = PPC_ACR_BUS_PARK_PCI;
+
+ /* Enable bus mastering and inbound memory transactions */
+ early_read_config_dword(hose, hose->first_busno, 0, PCI_COMMAND, &val);
+ val &= 0xffff0000;
+ val |= PCI_COMMAND_MEMORY|PCI_COMMAND_MASTER;
+ early_write_config_dword(hose, hose->first_busno, 0, PCI_COMMAND, val);
+
+}
+
+static void pq2ads_setup_hose(struct pci_controller * hose)
+{
+ hose->io_space.start = MPC826x_PCI_LOWER_IO;
+ hose->io_space.end = MPC826x_PCI_UPPER_IO;
+ hose->mem_space.start = MPC826x_PCI_LOWER_MEM;
+ hose->mem_space.end = MPC826x_PCI_UPPER_MMIO;
+ hose->io_base_virt = (void*)MPC826x_PCI_IO_BASE;
+ isa_io_base = MPC826x_PCI_IO_BASE;
+}
+
+#endif
+
+
+void __init pq2_find_bridges(void)
{
extern int pci_assign_all_busses;
struct pci_controller * hose;
+ int host_bridge;
pci_assign_all_busses = 1;
@@ -164,18 +439,45 @@
hose->bus_offset = 0;
hose->last_busno = 0xff;
+#ifdef CONFIG_ADS8272
+ hose->set_cfg_type = 1;
+#endif
+
setup_m8260_indirect_pci(hose,
(unsigned long)&cpm2_immr->im_pci.pci_cfg_addr,
(unsigned long)&cpm2_immr->im_pci.pci_cfg_data);
+ /* Make sure it is a supported bridge */
+ early_read_config_dword(hose,
+ 0,
+ PCI_DEVFN(0,0),
+ PCI_VENDOR_ID,
+ &host_bridge);
+ switch (host_bridge) {
+ case PCI_DEVICE_ID_MPC8265:
+ break;
+ case PCI_DEVICE_ID_MPC8272:
+ break;
+ default:
+ printk("Attempting to use unrecognized host bridge ID"
+ " 0x%08x.\n", host_bridge);
+ break;
+ }
+
+#if defined(CONFIG_ADS8272) || defined(CONFIG_PQ2FADS)
+ pq2ads_setup_pci(hose);
+ pq2ads_setup_hose(hose);
+#else
m8260_setup_pci(hose);
+
hose->pci_mem_offset = MPC826x_PCI_MEM_OFFSET;
- isa_io_base =
+ isa_io_base =
(unsigned long) ioremap(MPC826x_PCI_IO_BASE,
MPC826x_PCI_IO_SIZE);
hose->io_base_virt = (void *) isa_io_base;
-
+#endif
+
/* setup resources */
pci_init_resource(&hose->mem_resources[0],
MPC826x_PCI_LOWER_MEM,
@@ -191,4 +493,15 @@
MPC826x_PCI_LOWER_IO,
MPC826x_PCI_UPPER_IO,
IORESOURCE_IO, "PCI I/O");
+
+#if defined(CONFIG_ADS8272) || defined(CONFIG_PQ2FADS)
+ ppc_md.pci_exclude_device = pq2pci_exclude_device;
+ hose->last_busno = pciauto_bus_scan(hose, hose->first_busno);
+
+ ppc_md.pci_map_irq = pq2pci_map_irq;
+ ppc_md.pcibios_fixup = NULL;
+ ppc_md.pcibios_fixup_bus = NULL;
+
+#endif
+
}
===== arch/ppc/syslib/m8260_setup.c 1.30 vs edited =====
--- 1.30/arch/ppc/syslib/m8260_setup.c 2005-03-31 14:59:04 +04:00
+++ edited/arch/ppc/syslib/m8260_setup.c 2005-04-13 20:33:52 +04:00
@@ -34,7 +34,11 @@
unsigned char __res[sizeof(bd_t)];
extern void cpm2_reset(void);
+#if !defined(CONFIG_ADS8272) && !defined(CONFIG_PQ2FADS)
extern void m8260_find_bridges(void);
+#endif
+extern void pq2_find_bridges(void);
+extern void pq2pci_init_irq(void);
extern void idma_pci9_init(void);
/* Place-holder for board-specific init */
@@ -56,7 +60,11 @@
idma_pci9_init();
#endif
#ifdef CONFIG_PCI_8260
+#if defined(CONFIG_ADS8272) || defined(CONFIG_PQ2FADS)
+ pq2_find_bridges();
+#else
m8260_find_bridges();
+#endif
#endif
#ifdef CONFIG_BLK_DEV_INITRD
if (initrd_start)
@@ -173,6 +181,12 @@
* in case the boot rom changed something on us.
*/
cpm2_immr->im_intctl.ic_siprr = 0x05309770;
+
+#if defined(CONFIG_PCI) && (defined(CONFIG_ADS8272) || defined(CONFIG_PQ2FADS))
+ /* Initialize stuff for the 82xx CPLD IC and install demux */
+ pq2pci_init_irq();
+#endif
+
}
/*
@@ -195,6 +209,9 @@
m8260_map_io(void)
{
uint addr;
(galak is this io_block_mapping needed? we are trying to avoid using
io_block_mapping )
+#if defined(CONFIG_PCI) && (defined(CONFIG_ADS8272) || defined(CONFIG_PQ2FADS))
+ io_block_mapping(0x80000000,0x80000000,0x10000000, _PAGE_IO);
+#endif
/* Map IMMR region to a 256MB BAT */
addr = (cpm2_immr != NULL) ? (uint)cpm2_immr : CPM_MAP_ADDR;
===== include/asm-ppc/m8260_pci.h 1.1 vs edited =====
--- 1.1/include/asm-ppc/m8260_pci.h 2004-06-17 02:56:05 +04:00
+++ edited/include/asm-ppc/m8260_pci.h 2005-04-12 17:17:29 +04:00
@@ -19,6 +19,7 @@
* Define the vendor/device ID for the MPC8265.
*/
#define PCI_DEVICE_ID_MPC8265 ((0x18C0 << 16) | PCI_VENDOR_ID_MOTOROLA)
+#define PCI_DEVICE_ID_MPC8272 ((0x18C1 << 16) | PCI_VENDOR_ID_MOTOROLA)
#define M8265_PCIBR0 0x101ac
#define M8265_PCIBR1 0x101b0
More information about the Linuxppc-embedded
mailing list