A question about HHL?

Tue Oct 10 06:15:47 EST 2000

A couple thoughts:

1) The interrupt maps (pcore_pci.c) are different between the cpci and vme
   boards.  I've never used the vme board, but neither the built-in or pmc
   slots seam to use irq 12 that your log below shows the ethernet is using.

2) Instead of doing bootp auto configuration, you can try giving ip= and
   and nfsroot= (see /usr/src/linux/Documentation/nfsroot.txt on your
   RedHat host).  Be sure the last option for ip= is off.  If you still
   see network packets go out but never see any picked up, then that
   suggests problem 1, if the system comes up and runs the nfs just fine,
   then that suggests a different problem (maybe problem 3 below).

3) Did you see the arp notice in the README file. I don't think this is
   the problem because it is usually seen when f/w is trying to download
   the kernel with netload.  However, the problem might be different in
   the vme/cpci f/w.

Michael Pruznick, michael_pruznick at mvista.com,
MontaVista Software, 490 Potrero Ave, Sunnyvale, CA 94085
http://www.hardhatlinux.com

Pei-Jie Hong wrote:
>
> Dear All,
>         We recently found that HHL supports Force-Computer CPCI6750. But we
> have
> a Force-Computer Powercore6750, that we believe is primarily the same as
> CPCI6750,
> but which the backplane bus is vme bus not CPCI bus. And we try to boot
> it from a
> NFS server by using bootp. But it always can't get the bootp reply from
> the server.
> We have check the log file of the server, and sure that the server has
> received the
> bootp request and has sent bootp reply back. And also we check in
> function ic_bootp_recv,
> we found that it doesn't receive any packet. So, does anyone know what
> may be the problem?
> Thanks in advance.
>                                                                         Sincerely,
>                                                                         Pei-Jie Hong
> Below is the booting message of the board.
>
> Init serial 1 at address: 0xFE0003F8
> Init serial 2 at address: 0xFE0002F8
> Init CIO at address: 0xFE000300
> Init Ethernet Controller at address: 0xFE850000
> Init UNIVERSE VMEbus device at address: 0xFE810000
> PowerCore is VMEbus System Controller (SYSCON=1)
> Found CPU740/750, PVR=00088202,
> CPU clock: 376MHz, Bus clock: 83MHz
> SDRAM mode enabled, Parity disabled
> Onboard DRAM      : none
> Init DRAM Module 1:   64MB, 0x00000000..0x03FFFFFF
> Init DRAM Module 2:  none
> Init DTLB/ITLB for block translation, enable MMU
> Init L1-Icache
> Init L1-Dcache
> Init L2-Cache, found 1024 kByte cache, 125MHz
> Init exception vectors starting at address: 0x00000100
> Read NVRAM...identify board
> Read DEC SROM...done - CRC is OK
> Autoboot enabled.....TFTP Ethernet...RARP
>
>  Init Ethernet Controller MII-Port and PHY-Device
>  PHY-Device at 10MB/s negotiated
>  LAN-controller at address FE850000 set to Ethernet 00:80:42:0E:26:0C
>  Transmitting RARP-REQUEST... Reception of RARP-REPLY
>  Transmitting TFTP-REQUEST to server 00:50:E4:A6:B7:18, IP
> 137.138.100.60
>  PACKET:858 - loaded $00400000..$0046B3E3 (439268 bytes)
>
> Start execution at address 0x00400000
>
> Uncompressing kernel...done.
> Initializing clock.
> Load/PPC : console=ttyS0,9600 root=/dev/nfs
> Booting kernel...
> Total memory = 64MB; using 256kB for hash table (at c0140000)
> Linux version 2.2.14 (root at macl3tw1.cern.ch) (gcc version 2.95.2
> 19991030 (2.95.3 prerelease/franzo)) #95 Mon Oct 9 13:49:53 CEST 2000
> Boot arguments: console=ttyS0,9600 root=/dev/nfs
> time_init: decrementer frequency = 1237440720/60 (19MHz)
> Calibrating delay loop... 371.10 BogoMIPS
> Memory: 63468k available (692k kernel code, 1312k data, 64k init)
> [c0000000,c4000000]
> Dentry hash table entries: 8192 (order 4, 64k)
> Buffer cache hash table entries: 65536 (order 6, 256k)
> Page cache hash table entries: 16384 (order 4, 64k)
> POSIX conformance testing by UNIFIX
> PCI: Probing PCI hardware
> remapping IO (0x10e3:0x0 BAR 0): 0xbff001 -> 0xbff000
> remapping MEM(0x10e3:0x0 BAR 1): fcfff000 -> 0xfcfff000
> remapping IO (0x1011:0x19 BAR 0): 0xbfef81 -> 0xbfef80
> remapping MEM(0x1011:0x19 BAR 1): fcffec00 -> 0xfcffec00
> Linux NET4.0 for Linux 2.2
> Based upon Swansea University Computer Society NET3.039
> NET4: Linux TCP/IP 1.0 for NET4.0
> IP Protocols: ICMP, UDP, TCP
> TCP: Hash tables configured (ehash 65536 bhash 65536)
> Starting kswapd v 1.5
> Serial driver version 4.27 with no serial options enabled
> ttyS00 at 0x03f8 (irq = 4) is a 16550A
> ttyS01 at 0x02f8 (irq = 3) is a 16550A
> tulip.c:v0.91g-ppc 7/16/99 becker at cesdis.gsfc.nasa.gov
> eth0: Digital DS21143 Tulip rev 65 at 0xbfef80, 00:80:42:0E:26:0C, IRQ
> 12.
> eth0:  EEPROM default media type Autosense.
> eth0:  Index #0 - Media MII (#11) described by a 21142 MII PHY (3)
> block.
> eth0:  Index #1 - Media AUI (#2) described by a 21142 Serial PHY (2)
> block.
> eth0:  MII transceiver #1 config 1000 status 782d advertising 00a1.
> Sending BOOTP requests............<4>eth0: Tx hung, 14 vs. 0.
> . timed out!
> IP-Config: Auto-configuration of network failed.
> Root-NFS: No NFS server available, giving up.
> VFS: Unable to mount root fs via NFS, trying floppy.
> VFS: Cannot open root device 02:00
> Kernel panic: VFS: Unable to mount root fs on 02:00
> Rebooting in 180 seconds..
>

** Sent via the linuxppc-embedded mail list. See http://lists.linuxppc.org/