[PATCH v2 2/5] powerpc: 83xx/gpio: use new line value setter callbacks

[Christophe Leroy]

Le 02/05/2025 à 10:59, Bartosz Golaszewski a écrit :
> From: Bartosz Golaszewski <bartosz.golaszewski at linaro.org>
> 
> struct gpio_chip now has callbacks for setting line values that return
> an integer, allowing to indicate failures. Convert the driver to using
> them.
> 
> Reviewed-by: Linus Walleij <linus.walleij at linaro.org>
> Signed-off-by: Bartosz Golaszewski <bartosz.golaszewski at linaro.org>

Reviewed-by: Christophe Leroy <christophe.leroy at csgroup.eu>

> ---
>   arch/powerpc/platforms/83xx/mcu_mpc8349emitx.c | 13 ++++++++-----
>   1 file changed, 8 insertions(+), 5 deletions(-)
> 
> diff --git a/arch/powerpc/platforms/83xx/mcu_mpc8349emitx.c b/arch/powerpc/platforms/83xx/mcu_mpc8349emitx.c
> index 4d8fa9ed1a678..6e37dfc6c5c9e 100644
> --- a/arch/powerpc/platforms/83xx/mcu_mpc8349emitx.c
> +++ b/arch/powerpc/platforms/83xx/mcu_mpc8349emitx.c
> @@ -92,10 +92,11 @@ static void mcu_power_off(void)
>   	mutex_unlock(&mcu->lock);
>   }
>   
> -static void mcu_gpio_set(struct gpio_chip *gc, unsigned int gpio, int val)
> +static int mcu_gpio_set(struct gpio_chip *gc, unsigned int gpio, int val)
>   {
>   	struct mcu *mcu = gpiochip_get_data(gc);
>   	u8 bit = 1 << (4 + gpio);
> +	int ret;
>   
>   	mutex_lock(&mcu->lock);
>   	if (val)
> @@ -103,14 +104,16 @@ static void mcu_gpio_set(struct gpio_chip *gc, unsigned int gpio, int val)
>   	else
>   		mcu->reg_ctrl |= bit;
>   
> -	i2c_smbus_write_byte_data(mcu->client, MCU_REG_CTRL, mcu->reg_ctrl);
> +	ret = i2c_smbus_write_byte_data(mcu->client, MCU_REG_CTRL,
> +					mcu->reg_ctrl);
>   	mutex_unlock(&mcu->lock);
> +
> +	return ret;
>   }
>   
>   static int mcu_gpio_dir_out(struct gpio_chip *gc, unsigned int gpio, int val)
>   {
> -	mcu_gpio_set(gc, gpio, val);
> -	return 0;
> +	return mcu_gpio_set(gc, gpio, val);
>   }
>   
>   static int mcu_gpiochip_add(struct mcu *mcu)
> @@ -123,7 +126,7 @@ static int mcu_gpiochip_add(struct mcu *mcu)
>   	gc->can_sleep = 1;
>   	gc->ngpio = MCU_NUM_GPIO;
>   	gc->base = -1;
> -	gc->set = mcu_gpio_set;
> +	gc->set_rv = mcu_gpio_set;
>   	gc->direction_output = mcu_gpio_dir_out;
>   	gc->parent = dev;
>   
>