[PATCH v11 03/13] dt-bindings: Convert gpio-mmio to yaml
Krzysztof Kozlowski
krzysztof.kozlowski at linaro.org
Wed Mar 15 05:32:48 AEDT 2023
On 14/03/2023 19:09, Sean Anderson wrote:
> On 3/14/23 13:56, Krzysztof Kozlowski wrote:
>> On 13/03/2023 17:11, Sean Anderson wrote:
>>> This is a generic binding for simple MMIO GPIO controllers. Although we
>>> have a single driver for these controllers, they were previously spread
>>> over several files. Consolidate them. The register descriptions are
>>> adapted from the comments in the source. There is no set order for the
>>> registers, so I have not specified one.
>>>
>>> Rename brcm,bcm6345-gpio to brcm,bcm63xx-gpio to reflect that bcm6345
>>> has moved.
>>>
>>> Signed-off-by: Sean Anderson <sean.anderson at seco.com>
>>> Reviewed-by: Linus Walleij <linus.walleij at linaro.org>
>>> ---
>>> Linus or Bartosz, feel free to pick this up as the rest of this series
>>> may not be merged any time soon.
>>>
>>> Changes in v11:
>>> - Keep empty (or almost-empty) properties on a single line
>>> - Don't use | unnecessarily
>>> - Use gpio as the node name for examples
>>> - Rename brcm,bcm6345-gpio.yaml to brcm,bcm63xx-gpio.yaml
>>>
>>> Changes in v10:
>>> - New
>>>
>>> ...m6345-gpio.yaml => brcm,bcm63xx-gpio.yaml} | 16 +--
>>> .../devicetree/bindings/gpio/gpio-mmio.yaml | 134 ++++++++++++++++++
>>> .../bindings/gpio/ni,169445-nand-gpio.txt | 38 -----
>>> .../devicetree/bindings/gpio/wd,mbl-gpio.txt | 38 -----
>>> 4 files changed, 135 insertions(+), 91 deletions(-)
>>> rename Documentation/devicetree/bindings/gpio/{brcm,bcm6345-gpio.yaml => brcm,bcm63xx-gpio.yaml} (78%)
>>> create mode 100644 Documentation/devicetree/bindings/gpio/gpio-mmio.yaml
>>> delete mode 100644 Documentation/devicetree/bindings/gpio/ni,169445-nand-gpio.txt
>>> delete mode 100644 Documentation/devicetree/bindings/gpio/wd,mbl-gpio.txt
>>>
>>> diff --git a/Documentation/devicetree/bindings/gpio/brcm,bcm6345-gpio.yaml b/Documentation/devicetree/bindings/gpio/brcm,bcm63xx-gpio.yaml
>>> similarity index 78%
>>> rename from Documentation/devicetree/bindings/gpio/brcm,bcm6345-gpio.yaml
>>> rename to Documentation/devicetree/bindings/gpio/brcm,bcm63xx-gpio.yaml
>>> index 4d69f79df859..e11f4af49c52 100644
>>> --- a/Documentation/devicetree/bindings/gpio/brcm,bcm6345-gpio.yaml
>>> +++ b/Documentation/devicetree/bindings/gpio/brcm,bcm63xx-gpio.yaml
>>
>>
>>> +
>>> +description:
>>> + Some simple GPIO controllers may consist of a single data register or a pair
>>> + of set/clear-bit registers. Such controllers are common for glue logic in
>>> + FPGAs or ASICs. Commonly, these controllers are accessed over memory-mapped
>>> + NAND-style parallel busses.
>>> +
>>> +properties:
>>> + big-endian: true
>>> +
>>> + compatible:
>>
>> Keep compatible as first property.
>
> I thought it was alphabetical.
There is no clear rule, except that compatible is always first. In the
DTS reg is second, in bindings usually as well but not always.
>
>>> + enum:
>>> + - brcm,bcm6345-gpio # Broadcom BCM6345 GPIO controller
>>> + - wd,mbl-gpio # Western Digital MyBook Live memory-mapped GPIO controller
>>> + - ni,169445-nand-gpio # National Instruments 169445 GPIO NAND controller
>>
>> I think you got comment that these comments are making things
>> unreadable. I don't see here improvement.
>
> That was not the comment I got.
OK
>
> | I think you can inline description: statements in the enum instead of
> | the # hash comments, however IIRC you have to use oneOf and
> | const: to do it, like I do in
> | Documentation/devicetree/bindings/input/touchscreen/cypress,cy8ctma340.yaml
> | but don't overinvest in this if it is cumbersome.
>
> I investigated this and determined it was cumbersome.
So just :
# Western Digital MyBook Live memory-mapped GPIO controller
- wd,mbl-gpio
>
>> For example first comment is useless - you say the same as compatible.
>> Same with last one. So only remaining WD comment should be made in new
>> line so everything is nicely readable.
>
> I don't understand what you mean by "made in new line". Anyway, I will
> leave just the WD comment.
>
>> BTW, order the enum by name.
>
> OK
>
>>> +
>>> + '#gpio-cells':
>>> + const: 2
>>> +
>>> + gpio-controller:
>>> + true
>>
>> I am sure I saw comments here...
>>
>> https://lore.kernel.org/all/20230308231018.GA4039466-robh@kernel.org/
>
> OK
>
>>> +
>>> + reg:
>>> + minItems: 1
>>> + description:
>>> + A list of registers in the controller. The width of each register is
>>> + determined by its size.
>>
>> I don't understand this comment. Aren't you describing now what 'reg' is
>> in DT spec? If so, drop. If not, please share more.
>
> Each register describes exactly one hardware register. In some other
> device, when you see `regs = <0x8000000 0x100>`, then you may have 64
> 32-bit registers. But for this device, it would be one 2048-bit
> register.
Ah, so you do not mean here address space size? OK then, thanks for
clarification.
>
>>> All registers must have the same width. The number
>>> + of GPIOs is set by the width, with bit 0 corresponding to GPIO 0.
>>> + items:
>>> + - description:
>>> + Register to READ the value of the GPIO lines. If GPIO line is high,
>>> + the bit will be set. If the GPIO line is low, the bit will be cleared.
>>> + This register may also be used to drive GPIOs if the SET register is
>>> + omitted.
>>> + - description:
>>> + Register to SET the value of the GPIO lines. Setting a bit in this
>>> + register will drive the GPIO line high.
>>> + - description:
>>> + Register to CLEAR the value of the GPIO lines. Setting a bit in this
>>> + register will drive the GPIO line low. If this register is omitted,
>>> + the SET register will be used to clear the GPIO lines as well, by
>>> + actively writing the line with 0.
>>> + - description:
>>> + Register to set the line as OUTPUT. Setting a bit in this register
>>> + will turn that line into an output line. Conversely, clearing a bit
>>> + will turn that line into an input.
>>> + - description:
>>> + Register to set this line as INPUT. Setting a bit in this register
>>> + will turn that line into an input line. Conversely, clearing a bit
>>> + will turn that line into an output.
>>> +
>>> + reg-names:
>>> + minItems: 1
>>> + maxItems: 5
>>> + items:
>>> + enum:
>>
>> Why this is in any order? Other bindings were here specific, your 'reg'
>> is also specific/fixed.
>
> Some devicetrees have dirout first, and other have dat first. There is no
> mandatory order, and some registers can be included or left out as is
> convenient to the devicetree author.
>
> reg is not specific/fixed either. It is just done that way for
> convenience (and to match the names here).
The items have order and usually we require strict order from DTS,
unless there is a reason. If there is no reason, use fixed order and
then fix the DTS.
>
>>> + - dat
>>> + - set
>>> + - clr
>>> + - dirout
>>> + - dirin
>>> +
>>> + native-endian: true
>>> +
>>> + no-output:
>>> + $ref: /schemas/types.yaml#/definitions/flag
>>> + description:
>>> + If this property is present, the controller cannot drive the GPIO lines.
>>> +
>>> +required:
>>> + - compatible
>>> + - reg
>>> + - reg-names
>>> + - '#gpio-cells'
>>> + - gpio-controller
>>> +
>>> +additionalProperties: false
>>> +
>>> +examples:
>>> + - |
>>> + gpio at 1f300010 {
>>> + compatible = "ni,169445-nand-gpio";
>>> + reg = <0x1f300010 0x4>;
>>> + reg-names = "dat";
>>> + gpio-controller;
>>> + #gpio-cells = <2>;
>>> + };
>>> +
>>> + gpio at 1f300014 {
>>> + compatible = "ni,169445-nand-gpio";
>>> + reg = <0x1f300014 0x4>;
>>> + reg-names = "dat";
>>> + gpio-controller;
>>> + #gpio-cells = <2>;
>>> + no-output;
>>> + };
>>
>> No need to duplicate examples. Keep only one.
>
> OK
>
>> Everything is the same.
>
> Except no-output.
I would argue that even one example with no-output is enough, but sure,
can be two in total.
Best regards,
Krzysztof
More information about the Linuxppc-dev
mailing list