[PATCH v14 03/15] dt-bindings: Convert gpio-mmio to yaml
Rob Herring
robh at kernel.org
Wed Apr 19 06:37:32 AEST 2023
On Thu, Apr 13, 2023 at 12:05:55PM -0400, Sean Anderson wrote:
> This is a generic binding for simple MMIO GPIO controllers. Although we
> have a single driver for these controllers, they were previously spread
> over several files. Consolidate them. The register descriptions are
> adapted from the comments in the source. There is no set order for the
> registers, and some registers may be omitted. Because of this, reg-names
> is mandatory, and no order is specified.
>
> Rename brcm,bcm6345-gpio to brcm,bcm63xx-gpio to reflect that bcm6345
> has moved.
>
> Signed-off-by: Sean Anderson <sean.anderson at seco.com>
> Reviewed-by: Linus Walleij <linus.walleij at linaro.org>
> ---
> Linus or Bartosz, feel free to pick this up as the rest of this series
> may not be merged any time soon.
>
> Changes in v14:
> - Fix incorrect $id
>
> Changes in v13:
> - Fix references to brcm,bcm63xx-gpio.yaml (neé brcm,bcm6345-gpio)
>
> Changes in v12:
> - Put compatible first
> - Keep gpio-controller to one line
> - Add little-endian property
> - Alphabetize compatibles
> - Remove some comments
> - Remove some examples with insufficient novelty
>
> Changes in v11:
> - Keep empty (or almost-empty) properties on a single line
> - Don't use | unnecessarily
> - Use gpio as the node name for examples
> - Rename brcm,bcm6345-gpio.yaml to brcm,bcm63xx-gpio.yaml
>
> Changes in v10:
> - New
>
> ...m6345-gpio.yaml => brcm,bcm63xx-gpio.yaml} | 18 +--
> .../devicetree/bindings/gpio/gpio-mmio.yaml | 117 ++++++++++++++++++
> .../bindings/gpio/ni,169445-nand-gpio.txt | 38 ------
> .../devicetree/bindings/gpio/wd,mbl-gpio.txt | 38 ------
> .../mfd/brcm,bcm6318-gpio-sysctl.yaml | 4 +-
> .../mfd/brcm,bcm63268-gpio-sysctl.yaml | 4 +-
> .../mfd/brcm,bcm6328-gpio-sysctl.yaml | 4 +-
> .../mfd/brcm,bcm6358-gpio-sysctl.yaml | 4 +-
> .../mfd/brcm,bcm6362-gpio-sysctl.yaml | 4 +-
> .../mfd/brcm,bcm6368-gpio-sysctl.yaml | 4 +-
> 10 files changed, 131 insertions(+), 104 deletions(-)
> rename Documentation/devicetree/bindings/gpio/{brcm,bcm6345-gpio.yaml => brcm,bcm63xx-gpio.yaml} (75%)
> create mode 100644 Documentation/devicetree/bindings/gpio/gpio-mmio.yaml
> delete mode 100644 Documentation/devicetree/bindings/gpio/ni,169445-nand-gpio.txt
> delete mode 100644 Documentation/devicetree/bindings/gpio/wd,mbl-gpio.txt
>
> diff --git a/Documentation/devicetree/bindings/gpio/brcm,bcm6345-gpio.yaml b/Documentation/devicetree/bindings/gpio/brcm,bcm63xx-gpio.yaml
> similarity index 75%
> rename from Documentation/devicetree/bindings/gpio/brcm,bcm6345-gpio.yaml
> rename to Documentation/devicetree/bindings/gpio/brcm,bcm63xx-gpio.yaml
> index 4d69f79df859..62fcc2bd5d80 100644
> --- a/Documentation/devicetree/bindings/gpio/brcm,bcm6345-gpio.yaml
> +++ b/Documentation/devicetree/bindings/gpio/brcm,bcm63xx-gpio.yaml
> @@ -1,10 +1,10 @@
> # SPDX-License-Identifier: GPL-2.0-only OR BSD-2-Clause
> %YAML 1.2
> ---
> -$id: http://devicetree.org/schemas/gpio/brcm,bcm6345-gpio.yaml#
> +$id: http://devicetree.org/schemas/gpio/brcm,bcm63xx-gpio.yaml#
> $schema: http://devicetree.org/meta-schemas/core.yaml#
>
> -title: Broadcom BCM6345 GPIO controller
> +title: Broadcom BCM63xx GPIO controller
>
> maintainers:
> - Álvaro Fernández Rojas <noltari at gmail.com>
> @@ -18,8 +18,6 @@ description: |+
>
> BCM6338 have 8-bit data and dirout registers, where GPIO state can be read
> and/or written, and the direction changed from input to output.
> - BCM6345 have 16-bit data and dirout registers, where GPIO state can be read
> - and/or written, and the direction changed from input to output.
> BCM6318, BCM6328, BCM6358, BCM6362, BCM6368 and BCM63268 have 32-bit data
> and dirout registers, where GPIO state can be read and/or written, and the
> direction changed from input to output.
> @@ -29,7 +27,6 @@ properties:
> enum:
> - brcm,bcm6318-gpio
> - brcm,bcm6328-gpio
> - - brcm,bcm6345-gpio
> - brcm,bcm6358-gpio
> - brcm,bcm6362-gpio
> - brcm,bcm6368-gpio
> @@ -63,17 +60,6 @@ required:
> additionalProperties: false
>
> examples:
> - - |
> - gpio at fffe0406 {
> - compatible = "brcm,bcm6345-gpio";
> - reg-names = "dirout", "dat";
> - reg = <0xfffe0406 2>, <0xfffe040a 2>;
> - native-endian;
> -
> - gpio-controller;
> - #gpio-cells = <2>;
> - };
> -
> - |
> gpio at 0 {
> compatible = "brcm,bcm63268-gpio";
> diff --git a/Documentation/devicetree/bindings/gpio/gpio-mmio.yaml b/Documentation/devicetree/bindings/gpio/gpio-mmio.yaml
> new file mode 100644
> index 000000000000..b394e058256e
> --- /dev/null
> +++ b/Documentation/devicetree/bindings/gpio/gpio-mmio.yaml
> @@ -0,0 +1,117 @@
> +# SPDX-License-Identifier: (GPL-2.0-only OR BSD-2-Clause)
> +%YAML 1.2
> +---
> +$id: http://devicetree.org/schemas/gpio/gpio-mmio.yaml#
> +$schema: http://devicetree.org/meta-schemas/core.yaml#
> +
> +title: Generic MMIO GPIO
> +
> +maintainers:
> + - Linus Walleij <linus.walleij at linaro.org>
> + - Bartosz Golaszewski <brgl at bgdev.pl>
> +
> +description:
> + Some simple GPIO controllers may consist of a single data register or a pair
> + of set/clear-bit registers. Such controllers are common for glue logic in
> + FPGAs or ASICs. Commonly, these controllers are accessed over memory-mapped
> + NAND-style parallel busses.
> +
> +properties:
> + compatible:
> + enum:
> + - brcm,bcm6345-gpio
> + - ni,169445-nand-gpio
> + - wd,mbl-gpio # Western Digital MyBook Live memory-mapped GPIO controller
> +
> + big-endian: true
> +
> + '#gpio-cells':
> + const: 2
> +
> + gpio-controller: true
> +
> + little-endian: true
> +
> + reg:
> + minItems: 1
> + description:
> + A list of registers in the controller. The width of each register is
> + determined by its size. All registers must have the same width. The number
> + of GPIOs is set by the width, with bit 0 corresponding to GPIO 0.
> + items:
> + - description:
> + Register to READ the value of the GPIO lines. If GPIO line is high,
> + the bit will be set. If the GPIO line is low, the bit will be cleared.
> + This register may also be used to drive GPIOs if the SET register is
> + omitted.
> + - description:
> + Register to SET the value of the GPIO lines. Setting a bit in this
> + register will drive the GPIO line high.
> + - description:
> + Register to CLEAR the value of the GPIO lines. Setting a bit in this
> + register will drive the GPIO line low. If this register is omitted,
> + the SET register will be used to clear the GPIO lines as well, by
> + actively writing the line with 0.
> + - description:
> + Register to set the line as OUTPUT. Setting a bit in this register
> + will turn that line into an output line. Conversely, clearing a bit
> + will turn that line into an input.
> + - description:
> + Register to set this line as INPUT. Setting a bit in this register
> + will turn that line into an input line. Conversely, clearing a bit
> + will turn that line into an output.
> +
> + reg-names:
> + minItems: 1
> + maxItems: 5
> + items:
> + enum:
> + - dat
> + - set
> + - clr
> + - dirout
> + - dirin
> +
> + native-endian: true
> +
> + no-output:
> + $ref: /schemas/types.yaml#/definitions/flag
> + description:
> + If this property is present, the controller cannot drive the GPIO lines.
> +
> +required:
> + - compatible
> + - reg
> + - reg-names
> + - '#gpio-cells'
> + - gpio-controller
> +
> +additionalProperties: false
> +
> +examples:
> + - |
> + gpio at 1f300010 {
> + compatible = "ni,169445-nand-gpio";
> + reg = <0x1f300010 0x4>;
> + reg-names = "dat";
> + gpio-controller;
> + #gpio-cells = <2>;
> + };
> +
> + gpio at e0100000 {
> + compatible = "wd,mbl-gpio";
> + reg-names = "dat";
> + reg = <0xe0100000 0x1>;
> + #gpio-cells = <2>;
> + gpio-controller;
> + no-output;
> + };
> +
> + gpio at fffe0406 {
> + compatible = "brcm,bcm6345-gpio";
> + reg-names = "dirout", "dat";
> + reg = <0xfffe0406 2>, <0xfffe040a 2>;
> + native-endian;
> + gpio-controller;
> + #gpio-cells = <2>;
> + };
> diff --git a/Documentation/devicetree/bindings/gpio/ni,169445-nand-gpio.txt b/Documentation/devicetree/bindings/gpio/ni,169445-nand-gpio.txt
> deleted file mode 100644
> index ca2f8c745a27..000000000000
> --- a/Documentation/devicetree/bindings/gpio/ni,169445-nand-gpio.txt
> +++ /dev/null
> @@ -1,38 +0,0 @@
> -Bindings for the National Instruments 169445 GPIO NAND controller
> -
> -The 169445 GPIO NAND controller has two memory mapped GPIO registers, one
> -for input (the ready signal) and one for output (control signals). It is
> -intended to be used with the GPIO NAND driver.
> -
> -Required properties:
> - - compatible: should be "ni,169445-nand-gpio"
> - - reg-names: must contain
> - "dat" - data register
> - - reg: address + size pairs describing the GPIO register sets;
> - order must correspond with the order of entries in reg-names
> - - #gpio-cells: must be set to 2. The first cell is the pin number and
> - the second cell is used to specify the gpio polarity:
> - 0 = active high
> - 1 = active low
> - - gpio-controller: Marks the device node as a gpio controller.
> -
> -Optional properties:
> - - no-output: disables driving output on the pins
> -
> -Examples:
> - gpio1: nand-gpio-out at 1f300010 {
> - compatible = "ni,169445-nand-gpio";
> - reg = <0x1f300010 0x4>;
> - reg-names = "dat";
> - gpio-controller;
> - #gpio-cells = <2>;
> - };
> -
> - gpio2: nand-gpio-in at 1f300014 {
> - compatible = "ni,169445-nand-gpio";
> - reg = <0x1f300014 0x4>;
> - reg-names = "dat";
> - gpio-controller;
> - #gpio-cells = <2>;
> - no-output;
> - };
> diff --git a/Documentation/devicetree/bindings/gpio/wd,mbl-gpio.txt b/Documentation/devicetree/bindings/gpio/wd,mbl-gpio.txt
> deleted file mode 100644
> index 038c3a6a1f4d..000000000000
> --- a/Documentation/devicetree/bindings/gpio/wd,mbl-gpio.txt
> +++ /dev/null
> @@ -1,38 +0,0 @@
> -Bindings for the Western Digital's MyBook Live memory-mapped GPIO controllers.
> -
> -The Western Digital MyBook Live has two memory-mapped GPIO controllers.
> -Both GPIO controller only have a single 8-bit data register, where GPIO
> -state can be read and/or written.
> -
> -Required properties:
> - - compatible: should be "wd,mbl-gpio"
> - - reg-names: must contain
> - "dat" - data register
> - - reg: address + size pairs describing the GPIO register sets;
> - order must correspond with the order of entries in reg-names
> - - #gpio-cells: must be set to 2. The first cell is the pin number and
> - the second cell is used to specify the gpio polarity:
> - 0 = active high
> - 1 = active low
> - - gpio-controller: Marks the device node as a gpio controller.
> -
> -Optional properties:
> - - no-output: GPIOs are read-only.
> -
> -Examples:
> - gpio0: gpio0 at e0000000 {
> - compatible = "wd,mbl-gpio";
> - reg-names = "dat";
> - reg = <0xe0000000 0x1>;
> - #gpio-cells = <2>;
> - gpio-controller;
> - };
> -
> - gpio1: gpio1 at e0100000 {
> - compatible = "wd,mbl-gpio";
> - reg-names = "dat";
> - reg = <0xe0100000 0x1>;
> - #gpio-cells = <2>;
> - gpio-controller;
> - no-output;
> - };
> diff --git a/Documentation/devicetree/bindings/mfd/brcm,bcm6318-gpio-sysctl.yaml b/Documentation/devicetree/bindings/mfd/brcm,bcm6318-gpio-sysctl.yaml
> index 148f1da47603..9f9a14af875e 100644
> --- a/Documentation/devicetree/bindings/mfd/brcm,bcm6318-gpio-sysctl.yaml
> +++ b/Documentation/devicetree/bindings/mfd/brcm,bcm6318-gpio-sysctl.yaml
> @@ -35,11 +35,11 @@ patternProperties:
> "^gpio@[0-9a-f]+$":
> # Child node
> type: object
> - $ref: "../gpio/brcm,bcm6345-gpio.yaml"
> + $ref: "../gpio/brcm,bcm63xx-gpio.yaml"
If you respin, please drop the quotes here and the other spots.
Reviewed-by: Rob Herring <robh at kernel.org>
Rob
More information about the Linuxppc-dev
mailing list