[PATCH] serial: cpm_uart: Don't request IRQ too early for console port

Christophe Leroy christophe.leroy at csgroup.eu
Fri Sep 30 18:33:56 AEST 2022


The following message is seen during boot and the activation of
console port gets delayed until normal serial ports activation.

[    0.001346] irq: no irq domain found for pic at 930 !

The console port doesn't need irq, perform irq reservation later,
during cpm_uart probe.

While at it, don't use NO_IRQ but 0 which is the value returned
by irq_of_parse_and_map() in case of error. By chance powerpc's
NO_IRQ has value 0 but on some architectures it is -1.

Fixes: 14d893fc6846 ("powerpc/8xx: Convert CPM1 interrupt controller to platform_device")
Cc: stable at vger.kernel.org
Signed-off-by: Christophe Leroy <christophe.leroy at csgroup.eu>
---
 drivers/tty/serial/cpm_uart/cpm_uart_core.c | 22 ++++++++++-----------
 1 file changed, 10 insertions(+), 12 deletions(-)

diff --git a/drivers/tty/serial/cpm_uart/cpm_uart_core.c b/drivers/tty/serial/cpm_uart/cpm_uart_core.c
index db07d6a5d764..fa5c4633086e 100644
--- a/drivers/tty/serial/cpm_uart/cpm_uart_core.c
+++ b/drivers/tty/serial/cpm_uart/cpm_uart_core.c
@@ -1214,12 +1214,6 @@ static int cpm_uart_init_port(struct device_node *np,
 	pinfo->port.fifosize = pinfo->tx_nrfifos * pinfo->tx_fifosize;
 	spin_lock_init(&pinfo->port.lock);
 
-	pinfo->port.irq = irq_of_parse_and_map(np, 0);
-	if (pinfo->port.irq == NO_IRQ) {
-		ret = -EINVAL;
-		goto out_pram;
-	}
-
 	for (i = 0; i < NUM_GPIOS; i++) {
 		struct gpio_desc *gpiod;
 
@@ -1229,7 +1223,7 @@ static int cpm_uart_init_port(struct device_node *np,
 
 		if (IS_ERR(gpiod)) {
 			ret = PTR_ERR(gpiod);
-			goto out_irq;
+			goto out_pram;
 		}
 
 		if (gpiod) {
@@ -1255,8 +1249,6 @@ static int cpm_uart_init_port(struct device_node *np,
 
 	return cpm_uart_request_port(&pinfo->port);
 
-out_irq:
-	irq_dispose_mapping(pinfo->port.irq);
 out_pram:
 	cpm_uart_unmap_pram(pinfo, pram);
 out_mem:
@@ -1436,11 +1428,17 @@ static int cpm_uart_probe(struct platform_device *ofdev)
 	/* initialize the device pointer for the port */
 	pinfo->port.dev = &ofdev->dev;
 
+	pinfo->port.irq = irq_of_parse_and_map(ofdev->dev.of_node, 0);
+	if (!pinfo->port.irq)
+		return -EINVAL;
+
 	ret = cpm_uart_init_port(ofdev->dev.of_node, pinfo);
-	if (ret)
-		return ret;
+	if (!ret)
+		return uart_add_one_port(&cpm_reg, &pinfo->port);
 
-	return uart_add_one_port(&cpm_reg, &pinfo->port);
+	irq_dispose_mapping(pinfo->port.irq);
+
+	return ret;
 }
 
 static int cpm_uart_remove(struct platform_device *ofdev)
-- 
2.37.1



More information about the Linuxppc-dev mailing list