[PATCH] powerpc: e500: Fix compilation with gcc e500 compiler
Pali Rohár
pali at kernel.org
Mon Jul 4 23:13:58 AEST 2022
On Monday 04 July 2022 14:07:10 Arnd Bergmann wrote:
> On Mon, Jul 4, 2022 at 12:39 PM Pali Rohár <pali at kernel.org> wrote:
> > On Monday 04 July 2022 20:23:29 Michael Ellerman wrote:
> > > On 2 July 2022 7:44:05 pm AEST, "Pali Rohár" <pali at kernel.org> wrote:
> > > >On Tuesday 24 May 2022 11:39:39 Pali Rohár wrote:
> > > >> gcc e500 compiler does not support -mcpu=powerpc option. When it is
> > > >> specified then gcc throws compile error:
> > > >>
> > > >> gcc: error: unrecognized argument in option ‘-mcpu=powerpc’
> > > >> gcc: note: valid arguments to ‘-mcpu=’ are: 8540 8548 native
> > > >>
> > > >> So do not set -mcpu=powerpc option when CONFIG_E500 is set. Correct option
> > > >> -mcpu=8540 for CONFIG_E500 is set few lines below in that Makefile.
> > > >>
> > > >> Signed-off-by: Pali Rohár <pali at kernel.org>
> > > >> Cc: stable at vger.kernel.org
> > > >
> > > >Michael, do you have any objections about this patch?
> > >
> > > I don't particularly like it :)
> > >
> > > From the discussion with Segher, it sounds like this is a problem with a specific build of gcc that you're using, not a general problem with gcc built with e500 support.
> >
> > Well, the "full" build of gcc for e500 cores with SPE does not support
> > -mcpu=powerpc option. So I think this is a general problem. I do not
> > think that this is "specific build" as this is the correct build of gcc
> > for these processors with e500 cores.
> >
> > "stripped". build of gcc without SPE support for e500 cores does not
> > have this problem...
>
> I can see a couple of problems with the CPU selection, but I don't think
> this is a major one, as nobody should be using those SPE compilers for
> building the kernel. Just use a modern powerpc-gcc build.
The point is to use same compiler for building kernel as for the all
other parts of the system.
I just do not see reason why for kernel it is needed to build completely
different toolchain and compiler.
> > > Keying it off CONFIG_E500 means it will fix your problem, but not anyone else who has a different non-e500 compiler that also doesn't support -mcpu=powerpc (for whatever reason).
> > >
> > > So I wonder if a better fix is to use cc-option when setting -mcpu=powerpc.
> > >
> >
> > Comment for that code which adds -mpcu=powerpc says:
> >
> > they are needed to set a sane 32-bit cpu target for the 64-bit cross
> > compiler which may default to the wrong ISA.
> >
> > So I'm not sure how to handle this in other way. GCC uses -mpcu=8540
> > option for specifying to compile code for e500 cores and seems that
> > -mcpu=8540 is supported by all e500 compilers...
> >
> > Few lines below is code
> >
> > CFLAGS-$(CONFIG_E500) += $(call cc-option,-mcpu=8540 -msoft-float,-mcpu=powerpc)
> >
> > which for e500 kernel builds user either -mcpu=8540 or -mcpu=powerpc
> > (probably as a fallback if -mcpu=8540 is not supported).
>
> The -mcpu=powerpc fallback can probably be skipped here, that must have been
> for compilers predating the addition of -mcpu=8540, and even the oldest ones
> support that now.
Ok, makes sense.
> > So for me it looks like that problematic code
> >
> > KBUILD_CFLAGS += -mcpu=powerpc
> > KBUILD_AFLAGS += -mcpu=powerpc
> >
> > needs to be somehow skipped when compiling for CONFIG_E500.
> >> My change which skips that code base on ifndef CONFIG_E500 should be
> > fine as when CONFIG_E500 is disabled it does nothing and when it is
> > enabled then code
> >
> > CFLAGS-$(CONFIG_E500) += $(call cc-option,-mcpu=8540 -msoft-float,-mcpu=powerpc)
> >
> > is called which sets -mcpu option suitable for e500.
>
> I think this part is indeed fishy, but adding another special case for E500
> seems to take it in the wrong direction.
>
> Nick added this in 4bf4f42a2feb ("powerpc/kbuild: Set default generic
> machine type
> for 32-bit compile") as a compile-time fix to prevent the default target from
> getting used when the compiler supports both 64-bit and 32-bit. This is the
> right idea, but it's inconsistent to pass different flags depending on the type
> of toolchain, and it loses the more specific options.
>
> Another problem I see is that a kernel that is built for both E500 and E500MC
> uses -mcpu=e500mc and may not actually work on the older ones either
> (even with your patch).
That is probably truth, -mcpu=8540 should have been chosen. (Anyway it
should have been called -mcpu=e500, no idea why gcc still name it 8540.)
> I think what you actually want is to set one option for each of the
> possible CPU types:
>
> CFLAGS_CPU-$(CONFIG_PPC_BOOK3S_32) := -mcpu=powerpc
> CFLAGS_CPU-$(CONFIG_PPC_85xx) := -mcpu=8540
> CFLAGS_CPU-$(CONFIG_PPC8xx) := -mcpu=860
> CFLAGS_CPU-$(CONFIG_PPC44x) := -mcpu=440
> CFLAGS_CPU-$(CONFIG_PPC40x) := -mcpu=405
> ifdef CONFIG_CPU_LITTLE_ENDIAN
> CFLAGS_CPU-$(CONFIG_BOOK3S_64) := -mcpu=power8
> else
> CFLAGS_CPU-$(CONFIG_BOOK3S_64) := -mcpu=power5
> endif
> CFLAGS_CPU-$(CONFIG_BOOK3E_64) := -mcpu=powerpc64
Yes, this is something I would expect that in Makefile should be.
But what to do with fallback value?
> For the non-generic CPU types, there is also CONFIG_TARGET_CPU,
> and the list above could just get folded into that instead.
>
> Arnd
More information about the Linuxppc-dev
mailing list