[PATCH net-next] powerpc: dts: t208x: Disable 10G on MAC1 and MAC2
Sean Anderson
sean.anderson at seco.com
Fri Dec 16 03:32:40 AEDT 2022
On 12/15/22 11:12, Camelia Alexandra Groza wrote:
>> -----Original Message-----
>> From: Sean Anderson <sean.anderson at seco.com>
>> Sent: Thursday, November 3, 2022 23:29
>> To: David S . Miller <davem at davemloft.net>; netdev at vger.kernel.org
>> Cc: devicetree at vger.kernel.org; Michael Ellerman <mpe at ellerman.id.au>;
>> linux-kernel at vger.kernel.org; Rob Herring <robh+dt at kernel.org>;
>> Christophe Leroy <christophe.leroy at csgroup.eu>; linuxppc-
>> dev at lists.ozlabs.org; Nicholas Piggin <npiggin at gmail.com>; Krzysztof
>> Kozlowski <krzysztof.kozlowski+dt at linaro.org>; Sean Anderson
>> <sean.anderson at seco.com>; Camelia Alexandra Groza
>> <camelia.groza at nxp.com>
>> Subject: [PATCH net-next] powerpc: dts: t208x: Disable 10G on MAC1 and
>> MAC2
>>
>> There aren't enough resources to run these ports at 10G speeds. Just
>> keep the pcs changes, and revert the rest. This is not really correct,
>> since the hardware could support 10g in some other configuration...
>>
>> Fixes: 36926a7d70c2 ("powerpc: dts: t208x: Mark MAC1 and MAC2 as 10G")
>> Reported-by: Camelia Alexandra Groza <camelia.groza at nxp.com>
>> Signed-off-by: Sean Anderson <sean.anderson at seco.com>
>> ---
>>
>
> Hi Sean,
>
> I know I'm late, but there are a couple of issues with this patch. Do you intend
> on sending a v2 or should I pick it up?
>
>> .../boot/dts/fsl/qoriq-fman3-0-10g-2.dtsi | 45 -------------------
>> .../boot/dts/fsl/qoriq-fman3-0-10g-3.dtsi | 45 -------------------
>> arch/powerpc/boot/dts/fsl/t2081si-post.dtsi | 6 ++-
>> 3 files changed, 4 insertions(+), 92 deletions(-)
>> delete mode 100644 arch/powerpc/boot/dts/fsl/qoriq-fman3-0-10g-2.dtsi
>> delete mode 100644 arch/powerpc/boot/dts/fsl/qoriq-fman3-0-10g-3.dtsi
>>
>> diff --git a/arch/powerpc/boot/dts/fsl/qoriq-fman3-0-10g-2.dtsi
>> b/arch/powerpc/boot/dts/fsl/qoriq-fman3-0-10g-2.dtsi
>> deleted file mode 100644
>> index 6b3609574b0f..000000000000
>> --- a/arch/powerpc/boot/dts/fsl/qoriq-fman3-0-10g-2.dtsi
>> +++ /dev/null
>> @@ -1,45 +0,0 @@
>> -// SPDX-License-Identifier: BSD-3-Clause OR GPL-2.0-or-later
>> -/*
>> - * QorIQ FMan v3 10g port #2 device tree stub [ controller @ offset
>> 0x400000 ]
>> - *
>> - * Copyright 2022 Sean Anderson <sean.anderson at seco.com>
>> - * Copyright 2012 - 2015 Freescale Semiconductor Inc.
>> - */
>> -
>> -fman at 400000 {
>> - fman0_rx_0x08: port at 88000 {
>> - cell-index = <0x8>;
>> - compatible = "fsl,fman-v3-port-rx";
>> - reg = <0x88000 0x1000>;
>> - fsl,fman-10g-port;
>> - };
>> -
>> - fman0_tx_0x28: port at a8000 {
>> - cell-index = <0x28>;
>> - compatible = "fsl,fman-v3-port-tx";
>> - reg = <0xa8000 0x1000>;
>> - fsl,fman-10g-port;
>> - };
>> -
>> - ethernet at e0000 {
>> - cell-index = <0>;
>> - compatible = "fsl,fman-memac";
>> - reg = <0xe0000 0x1000>;
>> - fsl,fman-ports = <&fman0_rx_0x08 &fman0_tx_0x28>;
>> - ptp-timer = <&ptp_timer0>;
>> - pcsphy-handle = <&pcsphy0>, <&pcsphy0>;
>> - pcs-handle-names = "sgmii", "xfi";
>> - };
>> -
>> - mdio at e1000 {
>> - #address-cells = <1>;
>> - #size-cells = <0>;
>> - compatible = "fsl,fman-memac-mdio", "fsl,fman-xmdio";
>> - reg = <0xe1000 0x1000>;
>> - fsl,erratum-a011043; /* must ignore read errors */
>> -
>> - pcsphy0: ethernet-phy at 0 {
>> - reg = <0x0>;
>> - };
>> - };
>> -};
>> diff --git a/arch/powerpc/boot/dts/fsl/qoriq-fman3-0-10g-3.dtsi
>> b/arch/powerpc/boot/dts/fsl/qoriq-fman3-0-10g-3.dtsi
>> deleted file mode 100644
>> index 28ed1a85a436..000000000000
>> --- a/arch/powerpc/boot/dts/fsl/qoriq-fman3-0-10g-3.dtsi
>> +++ /dev/null
>> @@ -1,45 +0,0 @@
>> -// SPDX-License-Identifier: BSD-3-Clause OR GPL-2.0-or-later
>> -/*
>> - * QorIQ FMan v3 10g port #3 device tree stub [ controller @ offset
>> 0x400000 ]
>> - *
>> - * Copyright 2022 Sean Anderson <sean.anderson at seco.com>
>> - * Copyright 2012 - 2015 Freescale Semiconductor Inc.
>> - */
>> -
>> -fman at 400000 {
>> - fman0_rx_0x09: port at 89000 {
>> - cell-index = <0x9>;
>> - compatible = "fsl,fman-v3-port-rx";
>> - reg = <0x89000 0x1000>;
>> - fsl,fman-10g-port;
>> - };
>> -
>> - fman0_tx_0x29: port at a9000 {
>> - cell-index = <0x29>;
>> - compatible = "fsl,fman-v3-port-tx";
>> - reg = <0xa9000 0x1000>;
>> - fsl,fman-10g-port;
>> - };
>> -
>> - ethernet at e2000 {
>> - cell-index = <1>;
>> - compatible = "fsl,fman-memac";
>> - reg = <0xe2000 0x1000>;
>> - fsl,fman-ports = <&fman0_rx_0x09 &fman0_tx_0x29>;
>> - ptp-timer = <&ptp_timer0>;
>> - pcsphy-handle = <&pcsphy1>, <&pcsphy1>;
>> - pcs-handle-names = "sgmii", "xfi";
>> - };
>> -
>> - mdio at e3000 {
>> - #address-cells = <1>;
>> - #size-cells = <0>;
>> - compatible = "fsl,fman-memac-mdio", "fsl,fman-xmdio";
>> - reg = <0xe3000 0x1000>;
>> - fsl,erratum-a011043; /* must ignore read errors */
>> -
>> - pcsphy1: ethernet-phy at 0 {
>> - reg = <0x0>;
>> - };
>> - };
>> -};
>> diff --git a/arch/powerpc/boot/dts/fsl/t2081si-post.dtsi
>> b/arch/powerpc/boot/dts/fsl/t2081si-post.dtsi
>> index 74e17e134387..fed3879fa0aa 100644
>> --- a/arch/powerpc/boot/dts/fsl/t2081si-post.dtsi
>> +++ b/arch/powerpc/boot/dts/fsl/t2081si-post.dtsi
>> @@ -609,8 +609,8 @@ usb1: usb at 211000 {
>> /include/ "qoriq-bman1.dtsi"
>>
>> /include/ "qoriq-fman3-0.dtsi"
>> -/include/ "qoriq-fman3-0-10g-2.dtsi"
>> -/include/ "qoriq-fman3-0-10g-3.dtsi"
>> +/include/ "qoriq-fman3-0-1g-2.dtsi"
>> +/include/ "qoriq-fman3-0-1g-3.dtsi"
>
> These two should be qoriq-fman3-0-1g-0.dtsi and qoriq-fman3-0-1g-1.dtsi.
> You are including 1g-2.dtsi and 1g-3.dtsi twice.
So they should.
>> /include/ "qoriq-fman3-0-1g-2.dtsi"
>> /include/ "qoriq-fman3-0-1g-3.dtsi"
>> /include/ "qoriq-fman3-0-1g-4.dtsi"
>> @@ -619,9 +619,11 @@ usb1: usb at 211000 {
>> /include/ "qoriq-fman3-0-10g-1.dtsi"
>> fman at 400000 {
>> enet0: ethernet at e0000 {
>> + pcs-handle-names = "sgmii", "xfi";
>> };
>>
>> enet1: ethernet at e2000 {
>> + pcs-handle-names = "sgmii", "xfi";
>
> The second pcsphy for this port is still qsgmiia_pcs1 as described in
> qoriq-fman3-0-1g-1.dtsi. It should also be overwritten, not only the name
> property:
> pcsphy-handle = <&pcsphy1>, <&pcsphy1>;
This is the sort of reason I wanted to just delete the 10g property.
--Sean
>> };
>>
>> enet2: ethernet at e4000 {
>> --
>> 2.35.1.1320.gc452695387.dirty
>
More information about the Linuxppc-dev
mailing list