Errant readings on LM81 with T2080 SoC

[Chris Packham]

On 10/03/21 6:06 pm, Guenter Roeck wrote:
> On 3/9/21 6:19 PM, Chris Packham wrote:
>> On 9/03/21 9:27 am, Chris Packham wrote:
>>> On 8/03/21 5:59 pm, Guenter Roeck wrote:
>>>> Other than that, the only other real idea I have would be to monitor
>>>> the i2c bus.
>>> I am in the fortunate position of being able to go into the office and
>>> even happen to have the expensive scope at the moment. Now I just need
>>> to find a tame HW engineer so I don't burn myself trying to attach the
>>> probes.
>> One thing I see on the scope is that when there is a CPU load there
>> appears to be some clock stretching going on (SCL is held low some
>> times). I don't see it without the CPU load. It's hard to correlate a
>> clock stretching event with a bad read or error but it is one area where
>> the SMBUS spec has a maximum that might cause the device to give up waiting.
>>
> Do you have CONFIG_PREEMPT enabled in your kernel ? But even without
> that it is possible that the hot loops at the beginning and end of
> each operation mess up the driver and cause it to sleep longer
> than intended. Did you try usleep_range() ?

I've been running with and without CONFIG_PREEMPT. The failures happen 
with both.

I did try usleep_range() and still saw failures.

> On a side note, can you send me a register dump for the lm81 ?
> It would be useful for my module test code.

Here you go this is from a largely unconfigured LM81

      0  1  2  3  4  5  6  7  8  9  a  b  c  d  e  f 0123456789abcdef
00: 47 47 47 47 47 47 47 47 47 47 47 47 47 47 47 47 GGGGGGGGGGGGGGGG
10: 47 81 24 03 94 00 00 00 00 ff ff ff ff ff ff ff G?$??...........
20: bf cb c1 00 c0 47 ec 24 ff ff 65 ff 00 ff 00 ff ???.?G?$..e.....
30: 00 ff 00 ff 00 ff 00 71 a9 7f 7f ff ff 58 01 04 .......q???..X??
40: 01 08 00 00 00 00 00 50 2f 80 80 01 44 00 00 00 ??.....P/???D...
50: 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 ................
60: 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 ................
70: 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 ................
80: 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 ................
90: 00 81 24 03 94 00 00 00 00 ff ff ff ff ff ff ff .?$??...........
a0: bf cb c1 00 c0 47 ec 24 ff ff 65 ff 00 ff 00 ff ???.?G?$..e.....
b0: 00 ff 00 ff 00 ff 00 71 a9 7f 7f ff ff 58 01 04 .......q???..X??
c0: 01 00 00 00 00 00 00 50 2f 80 80 01 44 00 00 00 ?......P/???D...
d0: 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 ................
e0: 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 ................
f0: 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 ................

This is from a LM81 that's been configured by our application SW with 
limits appropriate for the platform.

      0  1  2  3  4  5  6  7  8  9  a  b  c  d  e  f 0123456789abcdef
00: ff ff ff ff ff ff ff ff ff ff ff ff ff ff ff ff ................
10: ff 81 24 03 94 00 00 00 00 ff ff ff ff ff ff ff ..$.............
20: bf cc c1 00 c0 47 ec 1c ff ff 65 dc b4 ff c0 d3 .....G....e.....
30: ad ff 00 d3 ad 4e 40 71 a9 4b 46 ff ff 58 01 04 .....N at q.KF..X..
40: 01 08 00 00 00 00 00 f0 2f 80 80 81 44 80 80 80 ......../...D...
50: 80 80 80 80 80 80 80 80 80 80 80 80 80 80 80 80 ................
60: 80 80 80 80 80 80 80 80 80 80 80 80 80 80 80 80 ................
70: 80 80 80 80 80 80 80 80 80 80 80 80 80 80 80 80 ................
80: 80 80 80 80 80 80 80 80 80 80 80 80 80 80 80 80 ................
90: 80 81 24 03 94 00 00 00 00 ff ff ff ff ff ff ff ..$.............
a0: bf cc c1 00 c0 47 ec 1c ff ff 65 dc b4 ff c0 d3 .....G....e.....
b0: ad ff 00 d3 ad 4e 40 71 a9 4b 46 ff ff 58 01 04 .....N at q.KF..X..
c0: 01 00 00 00 00 00 00 f0 2f 80 80 81 44 80 80 80 ......../...D...
d0: 80 80 80 80 80 80 80 80 80 80 80 80 80 80 80 80 ................
e0: 80 80 80 80 80 80 80 80 80 80 80 80 80 80 80 80 ................
f0: 80 80 80 80 80 80 80 80 80 80 80 80 80 80 80 80 ................