[PATCH v3 3/5] powerpc: apm82181: add WD MyBook Live NAS
Christian Lamparter
chunkeey at gmail.com
Sun Sep 6 08:06:13 AEST 2020
This patch adds the device-tree definitions for
Western Digital MyBook Live NAS devices.
CPU: AMCC PowerPC APM82181 (PVR=12c41c83) at 800 MHz
(PLB=200, OPB=100, EBC=100 MHz)
32 kB I-Cache 32 kB D-Cache, 256 kB L2-Cache, 32 kB OnChip Memory
DRAM: 256 MB (2x NT5TU64M16GG-AC)
FLASH: 512 kB
Ethernet: 1xRGMII - 1 Gbit - Broadcom PHY BCM54610
SATA: 2*SATA (DUO Variant) / 1*SATA (Single Variant)
USB: 1xUSB2.0 (Only DUO)
Technically, this devicetree file is shared by two, very
similar devices.
There's the My Book Live and the My Book Live Duo. WD's uboot
on the device will enable/disable the nodes for the device.
This device boots from a u-boot on a 512 KiB NOR Flash onto a
Linux image stored on one of the harddrives.
Ready to go images and install instruction can be found @OpenWrt.org
Signed-off-by: Christian Lamparter <chunkeey at gmail.com>
---
rfc v1 -> v2:
- use new LED naming scheme
- dish out read-only; for essential NOR partitions
- remove openwrt led-aliases
- comment on the location of linux kernel (on the HDD)
- overhauled commit message
v2 -> v3:
- "jedec-probe" should be "jedec,spi-nor"
---
arch/powerpc/boot/dts/wd-mybooklive.dts | 200 +++++++++++++++++++++
arch/powerpc/platforms/44x/ppc44x_simple.c | 3 +-
2 files changed, 202 insertions(+), 1 deletion(-)
create mode 100644 arch/powerpc/boot/dts/wd-mybooklive.dts
diff --git a/arch/powerpc/boot/dts/wd-mybooklive.dts b/arch/powerpc/boot/dts/wd-mybooklive.dts
new file mode 100644
index 000000000000..8fe868252cb5
--- /dev/null
+++ b/arch/powerpc/boot/dts/wd-mybooklive.dts
@@ -0,0 +1,200 @@
+// SPDX-License-Identifier: GPL-2.0-only
+/*
+ * Copyright 2008 DENX Software Engineering, Stefan Roese <sr at denx.de>
+ * (c) Copyright 2010 Western Digital Technologies, Inc. All Rights Reserved.
+ */
+
+/dts-v1/;
+
+#include <dt-bindings/leds/common.h>
+#include "apm82181.dtsi"
+
+/ {
+ compatible = "wd,mybooklive";
+ model = "MyBook Live";
+
+ aliases {
+ serial0 = &UART0;
+ };
+};
+
+&POB0 {
+ GPIO1: gpio at e0000000 {
+ compatible = "wd,mbl-gpio";
+ reg-names = "dat";
+ reg = <0xe0000000 0x1>;
+ #gpio-cells = <2>;
+ gpio-controller;
+
+ enable-button {
+ /* Defined in u-boot as: NOT_NOR
+ * "enables features other than NOR
+ * specifically, the buffer at CS2"
+ * (button).
+ *
+ * Note: This option is disabled as
+ * it prevents the system from being
+ * rebooted successfully.
+ */
+
+ gpio-hog;
+ line-name = "Enable Reset Button, disable NOR";
+ gpios = <1 GPIO_ACTIVE_HIGH>;
+ output-low;
+ };
+ };
+
+ GPIO2: gpio at e0100000 {
+ compatible = "wd,mbl-gpio";
+ reg-names = "dat";
+ reg = <0xe0100000 0x1>;
+ #gpio-cells = <2>;
+ gpio-controller;
+ no-output;
+ };
+
+ leds {
+ compatible = "gpio-leds";
+
+ /* There's just one tri-color LED. */
+ failsafe: power-red {
+ function = LED_FUNCTION_FAULT;
+ color = <LED_COLOR_ID_RED>;
+ gpios = <&GPIO1 4 GPIO_ACTIVE_HIGH>;
+ linux,default-trigger = "panic";
+ };
+
+ power-green {
+ function = LED_FUNCTION_POWER;
+ color = <LED_COLOR_ID_GREEN>;
+ gpios = <&GPIO1 5 GPIO_ACTIVE_HIGH>;
+ };
+
+ power-blue {
+ function = LED_FUNCTION_DISK;
+ color = <LED_COLOR_ID_BLUE>;
+ gpios = <&GPIO1 6 GPIO_ACTIVE_HIGH>;
+ linux,default-trigger = "disk-activity";
+ };
+ };
+
+ keys {
+ compatible = "gpio-keys-polled";
+ poll-interval = <60>; /* 3 * 20 = 60ms */
+ autorepeat;
+
+ reset-button {
+ label = "Reset button";
+ linux,code = <KEY_RESTART>;
+ gpios = <&GPIO2 2 GPIO_ACTIVE_LOW>;
+ };
+ };
+
+ usbpwr: usb-regulator {
+ compatible = "regulator-fixed";
+ regulator-name = "Power USB Core";
+ gpios = <&GPIO1 2 GPIO_ACTIVE_LOW>;
+ regulator-min-microvolt = <5000000>;
+ regulator-max-microvolt = <5000000>;
+ };
+
+ sata1pwr: sata1-regulator {
+ compatible = "regulator-fixed";
+ regulator-name = "Power Drive Port 1";
+ gpios = <&GPIO1 3 GPIO_ACTIVE_LOW>;
+ regulator-min-microvolt = <12000000>;
+ regulator-max-microvolt = <12000000>;
+ regulator-always-on; /* needed to read OS from HDD */
+ };
+
+ sata0pwr: sata0-regulator {
+ compatible = "regulator-fixed";
+ regulator-name = "Power Drive Port 0";
+ gpios = <&GPIO1 7 GPIO_ACTIVE_LOW>;
+ regulator-min-microvolt = <12000000>;
+ regulator-max-microvolt = <12000000>;
+ regulator-always-on; /* needed to read OS from HDD */
+ };
+};
+
+&NOR {
+ status = "okay";
+ compatible = "jedec,spi-nor";
+ bank-width = <1>;
+ reg = <0x00000000 0x00000000 0x00080000>;
+ #address-cells = <1>;
+ #size-cells = <1>;
+
+ partition at 0 {
+ /* Part of bootrom - Don't use it without a jump */
+ label = "bootrom";
+ reg = <0x00000000 0x0001e000>;
+ read-only;
+ };
+
+ partition at 1e000 {
+ label = "env";
+ reg = <0x0001e000 0x00002000>;
+ };
+
+ partition at 20000 {
+ label = "uboot";
+ reg = <0x00020000 0x00050000>;
+ read-only;
+ };
+};
+
+&EMAC0 {
+ status = "okay";
+
+ phy-map = <0x2>;
+ phy-address = <0x1>;
+ phy-handle = <&phy>;
+
+ mdio {
+ #address-cells = <1>;
+ #size-cells = <0>;
+ reset-gpios = <&GPIO1 0 GPIO_ACTIVE_LOW>;
+
+ phy: phy at 1 {
+ compatible = "ethernet-phy-ieee802.3-c22";
+ reg = <1>;
+ };
+ };
+};
+
+&CRYPTO {
+ status = "okay";
+};
+
+&HWRNG {
+ status = "okay";
+};
+
+&SATA0 {
+ status = "okay";
+
+ drive0: sata-port at 0 {
+ reg = <0>;
+ #thermal-sensor-cells = <0>;
+ };
+};
+
+&SATA1 {
+ status = "okay";
+
+ drive1: sata-port at 0 {
+ reg = <0>;
+ #thermal-sensor-cells = <0>;
+ };
+};
+
+&UART0 {
+ status = "okay";
+};
+
+&USBOTG0 {
+ status = "okay";
+ dr_mode = "host";
+ vbus-supply = <&usbpwr>;
+};
diff --git a/arch/powerpc/platforms/44x/ppc44x_simple.c b/arch/powerpc/platforms/44x/ppc44x_simple.c
index 3dbd8ddd734a..1122702c804a 100644
--- a/arch/powerpc/platforms/44x/ppc44x_simple.c
+++ b/arch/powerpc/platforms/44x/ppc44x_simple.c
@@ -59,7 +59,8 @@ static char *board[] __initdata = {
"amcc,sequoia",
"amcc,taishan",
"amcc,yosemite",
- "mosaixtech,icon"
+ "mosaixtech,icon",
+ "wd,mybooklive",
};
static int __init ppc44x_probe(void)
--
2.28.0
More information about the Linuxppc-dev
mailing list