[PATCH v2 4/6] powerpc/pseries/iommu: Remove default DMA window before creating DDW

[Alexey Kardashevskiy]

On 24/06/2020 16:24, Leonardo Bras wrote:
> On LoPAR "DMA Window Manipulation Calls", it's recommended to remove the
> default DMA window for the device, before attempting to configure a DDW,
> in order to make the maximum resources available for the next DDW to be
> created.
> 
> This is a requirement for some devices to use DDW, given they only
> allow one DMA window.


Devices never know about these windows, it is purely PHB's side of
things. A device can access any address on the bus, the bus can generate
an exception if there is no window behind the address OR some other
device's MMIO. We could actually create a second window in addition to
the first one and allocate bus addresses from both, we just simplifying
this by merging two separate non-adjacent windows into one.


> 
> If setting up a new DDW fails anywhere after the removal of this
> default DMA window, it's needed to restore the default DMA window.
> For this, an implementation of ibm,reset-pe-dma-windows rtas call is
> needed:
> 
> Platforms supporting the DDW option starting with LoPAR level 2.7 implement
> ibm,ddw-extensions. The first extension available (index 2) carries the
> token for ibm,reset-pe-dma-windows rtas call, which is used to restore
> the default DMA window for a device, if it has been deleted.
> 
> It does so by resetting the TCE table allocation for the PE to it's
> boot time value, available in "ibm,dma-window" device tree node.
> 
> Signed-off-by: Leonardo Bras <leobras.c at gmail.com>
> ---
>  arch/powerpc/platforms/pseries/iommu.c | 70 ++++++++++++++++++++++----
>  1 file changed, 61 insertions(+), 9 deletions(-)
> 
> diff --git a/arch/powerpc/platforms/pseries/iommu.c b/arch/powerpc/platforms/pseries/iommu.c
> index a8840d9e1c35..4fcf00016fb1 100644
> --- a/arch/powerpc/platforms/pseries/iommu.c
> +++ b/arch/powerpc/platforms/pseries/iommu.c
> @@ -1029,6 +1029,39 @@ static phys_addr_t ddw_memory_hotplug_max(void)
>  	return max_addr;
>  }
>  
> +/*
> + * Platforms supporting the DDW option starting with LoPAR level 2.7 implement
> + * ibm,ddw-extensions, which carries the rtas token for
> + * ibm,reset-pe-dma-windows.
> + * That rtas-call can be used to restore the default DMA window for the device.
> + */
> +static void reset_dma_window(struct pci_dev *dev, struct device_node *par_dn)
> +{
> +	int ret;
> +	u32 cfg_addr, ddw_ext[DDW_EXT_RESET_DMA_WIN + 1];
> +	u64 buid;
> +	struct device_node *dn;
> +	struct pci_dn *pdn;
> +
> +	ret = of_property_read_u32_array(par_dn, "ibm,ddw-extensions",
> +					 &ddw_ext[0], DDW_EXT_RESET_DMA_WIN + 1);
> +	if (ret)
> +		return;
> +
> +	dn = pci_device_to_OF_node(dev);
> +	pdn = PCI_DN(dn);
> +	buid = pdn->phb->buid;
> +	cfg_addr = ((pdn->busno << 16) | (pdn->devfn << 8));
> +
> +	ret = rtas_call(ddw_ext[DDW_EXT_RESET_DMA_WIN], 3, 1, NULL, cfg_addr,
> +			BUID_HI(buid), BUID_LO(buid));
> +	if (ret)
> +		dev_info(&dev->dev,
> +			 "ibm,reset-pe-dma-windows(%x) %x %x %x returned %d ",
> +			 ddw_ext[1], cfg_addr, BUID_HI(buid), BUID_LO(buid),


s/ddw_ext[1]/ddw_ext[DDW_EXT_RESET_DMA_WIN]/


> +			 ret);
> +}
> +
>  /*
>   * If the PE supports dynamic dma windows, and there is space for a table
>   * that can map all pages in a linear offset, then setup such a table,
> @@ -1049,8 +1082,9 @@ static u64 enable_ddw(struct pci_dev *dev, struct device_node *pdn)
>  	u64 dma_addr, max_addr;
>  	struct device_node *dn;
>  	u32 ddw_avail[DDW_APPLICABLE_SIZE];
> +

Unrelated new empty line.


>  	struct direct_window *window;
> -	struct property *win64;
> +	struct property *win64, *default_win = NULL, *ddw_ext = NULL;
>  	struct dynamic_dma_window_prop *ddwprop;
>  	struct failed_ddw_pdn *fpdn;
>  
> @@ -1085,7 +1119,7 @@ static u64 enable_ddw(struct pci_dev *dev, struct device_node *pdn)
>  	if (ret)
>  		goto out_failed;
>  
> -       /*
> +	/*
>  	 * Query if there is a second window of size to map the
>  	 * whole partition.  Query returns number of windows, largest
>  	 * block assigned to PE (partition endpoint), and two bitmasks
> @@ -1096,15 +1130,31 @@ static u64 enable_ddw(struct pci_dev *dev, struct device_node *pdn)
>  	if (ret != 0)
>  		goto out_failed;
>  
> +	/*
> +	 * If there is no window available, remove the default DMA window,
> +	 * if it's present. This will make all the resources available to the
> +	 * new DDW window.
> +	 * If anything fails after this, we need to restore it, so also check
> +	 * for extensions presence.
> +	 */
>  	if (query.windows_available == 0) {


Does phyp really always advertise 0 windows for these VFs? What is in
the largest_available_block when windows_available==0?


> -		/*
> -		 * no additional windows are available for this device.
> -		 * We might be able to reallocate the existing window,
> -		 * trading in for a larger page size.
> -		 */
> -		dev_dbg(&dev->dev, "no free dynamic windows");
> -		goto out_failed;
> +		default_win = of_find_property(pdn, "ibm,dma-window", NULL);
> +		ddw_ext = of_find_property(pdn, "ibm,ddw-extensions", NULL);
> +		if (default_win && ddw_ext)
> +			remove_dma_window(pdn, ddw_avail, default_win);
> +
> +		/* Query again, to check if the window is available */
> +		ret = query_ddw(dev, ddw_avail, &query, pdn);
> +		if (ret != 0)
> +			goto out_failed;
> +
> +		if (query.windows_available == 0) {
> +			/* no windows are available for this device. */
> +			dev_dbg(&dev->dev, "no free dynamic windows");
> +			goto out_failed;
> +		}
>  	}
> +


Unrelated new empty line. Thanks,

>  	if (query.page_size & 4) {
>  		page_shift = 24; /* 16MB */
>  	} else if (query.page_size & 2) {
> @@ -1194,6 +1244,8 @@ static u64 enable_ddw(struct pci_dev *dev, struct device_node *pdn)
>  	kfree(win64);
>  
>  out_failed:
> +	if (default_win && ddw_ext)
> +		reset_dma_window(dev, pdn);
>  
>  	fpdn = kzalloc(sizeof(*fpdn), GFP_KERNEL);
>  	if (!fpdn)
> 

-- 
Alexey