[PATCH v3 12/27] powerpc/powernv/pmem: Add register addresses & status values to the header

[Alastair D'Silva]

On Thu, 2020-02-27 at 16:08 +1100, Andrew Donnellan wrote:
> On 21/2/20 2:27 pm, Alastair D'Silva wrote:
> > From: Alastair D'Silva <alastair at d-silva.org>
> > 
> > These values have been taken from the device specifications.
> > 
> > Signed-off-by: Alastair D'Silva <alastair at d-silva.org>
> 
> I've compared these values against the internal version of the
> device 
> specifications that I have access to, and they appear to match.
> 
> A few minor comments below, otherwise:
> 
> Reviewed-by: Andrew Donnellan <ajd at linux.ibm.com>
> 
> > +#define GLOBAL_MMIO_HCI_ACRW				BIT_ULL
> > (0)
> > +#define GLOBAL_MMIO_HCI_NSCRW				BIT_ULL
> > (1)
> > +#define GLOBAL_MMIO_HCI_AFU_RESET			BIT_ULL(2)
> > +#define GLOBAL_MMIO_HCI_FW_DEBUG			BIT_ULL(3)
> > +#define GLOBAL_MMIO_HCI_CONTROLLER_DUMP			BIT_ULL
> > (4)
> > +#define GLOBAL_MMIO_HCI_CONTROLLER_DUMP_COLLECTED	BIT_ULL(5)
> > +#define GLOBAL_MMIO_HCI_REQ_HEALTH_PERF			BIT_ULL
> > (6)
> 
> The labelling of some of these bits deviates from the standard 
> abbreviations in the spec, which is fine I guess as these names are
> more 
> descriptive, but maybe add a brief comment with the original
> abbreviation?
> 

Ok

> > +
> > +#define ADMIN_COMMAND_HEARTBEAT		0x00u
> > +#define ADMIN_COMMAND_SHUTDOWN		0x01u
> > +#define ADMIN_COMMAND_FW_UPDATE		0x02u
> > +#define ADMIN_COMMAND_FW_DEBUG		0x03u
> > +#define ADMIN_COMMAND_ERRLOG		0x04u
> > +#define ADMIN_COMMAND_SMART		0x05u
> > +#define ADMIN_COMMAND_CONTROLLER_STATS	0x06u
> > +#define ADMIN_COMMAND_CONTROLLER_DUMP	0x07u
> > +#define ADMIN_COMMAND_CMD_CAPS		0x08u
> > +#define ADMIN_COMMAND_MAX		0x08u
> > +
> > +#define STATUS_SUCCESS		0x00
> > +#define STATUS_MEM_UNAVAILABLE	0x20
> 
> There's also a "blocked on account of background task" code, 0x21.
> 

Ok

> > +#define STATUS_BAD_OPCODE	0x50
> > +#define STATUS_BAD_REQUEST_PARM	0x51
> > +#define STATUS_BAD_DATA_PARM	0x52
> > +#define STATUS_DEBUG_BLOCKED	0x70
> > +#define STATUS_FAIL		0xFF
> > +
> > +#define STATUS_FW_UPDATE_BLOCKED 0x21
> > +#define STATUS_FW_ARG_INVALID	0x51
> > +#define STATUS_FW_INVALID	0x52
> 
> These status codes seem, from the specification, to correspond to
> the 
> generic error codes above, so perhaps they're not needed.
> 

These will be used in warn_status_fw_update() later, but I'll alias
them to make it clear that they are shadowing values

-- 
Alastair D'Silva
Open Source Developer
Linux Technology Centre, IBM Australia
mob: 0423 762 819