[PATCH v4 1/2] dt-bindings: soc: fsl: Document Qixis FPGA usage

[Leo Li]

> -----Original Message-----
> From: Pankaj Bansal
> Sent: Tuesday, February 5, 2019 4:15 AM
> To: Leo Li <leoyang.li at nxp.com>; Rob Herring <robh+dt at kernel.org>; Mark
> Rutland <mark.rutland at arm.com>
> Cc: linuxppc-dev at lists.ozlabs.org; linux-arm-kernel at lists.infradead.org;
> open list : OPEN FIRMWARE AND FLATTENED DEVICE TREE BINDINGS
> <devicetree at vger.kernel.org>; Pankaj Bansal <pankaj.bansal at nxp.com>
> Subject: [PATCH v4 1/2] dt-bindings: soc: fsl: Document Qixis FPGA usage
> 
> an FPGA-based system controller, called “Qixis”, which
> manages several critical system features, including:
> • Reset sequencing
> • Power supply configuration
> • Board configuration
> • hardware configuration
> 
> The qixis registers are accessible over one or more system-specific
> interfaces, typically I2C, JTAG or an embedded processor.

In theory the on-board FPGA is not part of the SoC.  The Qixis device has been defined previously in Documentation/devicetree/bindings/board/fsl-board.txt file.  Although normally board bindings are defined in architecture specific binding folders, this is a good place for board related stuff used across multiple architectures.  You can update the existing binding if needed.

> 
> Signed-off-by: Pankaj Bansal <pankaj.bansal at nxp.com>
> ---
> 
> Notes:
>     V4:
>     - No Change
>     V3:
>     - Added boardname based compatible field in bindings
>     - Added bindings for MMIO based FPGA
>     V2:
>     - No change
> 
>  .../bindings/soc/fsl/qixis_ctrl.txt          | 53 ++++++++++++++++++
>  1 file changed, 53 insertions(+)
> 
> diff --git a/Documentation/devicetree/bindings/soc/fsl/qixis_ctrl.txt
> b/Documentation/devicetree/bindings/soc/fsl/qixis_ctrl.txt
> new file mode 100644
> index 000000000000..5d510df14be8
> --- /dev/null
> +++ b/Documentation/devicetree/bindings/soc/fsl/qixis_ctrl.txt
> @@ -0,0 +1,53 @@
> +* QIXIS FPGA block
> +
> +an FPGA-based system controller, called “Qixis”, which
> +manages several critical system features, including:
> +• Configuration switch monitoring
> +• Power on/off sequencing
> +• Reset sequencing
> +• Power supply configuration
> +• Board configuration
> +• hardware configuration
> +• Background power data collection (DCM)
> +• Fault monitoring
> +• RCW bypass SRAM (replace flash RCW with internal RCW) (NOR only)
> +• Dedicated functional validation blocks (POSt/IRS, triggered event, and so
> on)
> +• I2C master for remote board control even with no DUT available
> +
> +The qixis registers are accessible over one or more system-specific
> interfaces,
> +typically I2C, JTAG or an embedded processor.
> +
> +FPGA connected to I2C:
> +Required properties:
> +
> + - compatible: should be a board-specific string followed by a string
> +   indicating the type of FPGA.  Example:
> +	"fsl,<board>-fpga", "fsl,fpga-qixis-i2c"
> + - reg : i2c address of the qixis device.
> +
> +Example (LX2160A-QDS):
> +	/* The FPGA node */
> +        fpga at 66 {
> +		compatible = "fsl,lx2160aqds-fpga", "fsl,fpga-qixis-i2c";
> +		reg = <0x66>;
> +		#address-cells = <1>;
> +		#size-cells = <0>;
> +	}
> +
> +* Freescale on-board FPGA
> +
> +This is the memory-mapped registers for on board FPGA.
> +
> +Required properties:
> +- compatible: should be a board-specific string followed by a string
> +  indicating the type of FPGA.  Example:
> +	"fsl,<board>-fpga", "fsl,fpga-qixis"
> +- reg: should contain the address and the length of the FPGA register set.
> +
> +Example (LS2080A-RDB):
> +
> +        cpld at 3,0 {
> +                compatible = "fsl,ls2080ardb-fpga", "fsl,fpga-qixis";
> +                reg = <0x3 0 0x10000>;
> +        };
> +
> --
> 2.17.1