[PATCH 40/41] drivers: tty: serial: helper for setting mmio range
Enrico Weigelt, metux IT consult
info at metux.net
Sat Apr 27 22:52:21 AEST 2019
Introduce a little helpers for settings the mmio range from an
struct resource or start/len parameters with less code.
(also setting iotype to UPIO_MEM)
Also converting drivers to use these new helpers as well as
fetching mapsize field instead of using hardcoded values.
(the runtime overhead of that should be negligible)
The idea is moving to a consistent scheme, so later common
calls like request+ioremap combination can be done by generic
helpers.
Signed-off-by: Enrico Weigelt <info at metux.net>
---
drivers/tty/serial/8250/8250_acorn.c | 5 ++--
drivers/tty/serial/8250/8250_aspeed_vuart.c | 4 +--
drivers/tty/serial/8250/8250_dw.c | 3 +--
drivers/tty/serial/8250/8250_em.c | 2 +-
drivers/tty/serial/8250/8250_exar.c | 6 +++--
drivers/tty/serial/8250/8250_hp300.c | 11 +++++---
drivers/tty/serial/8250/8250_of.c | 9 ++-----
drivers/tty/serial/meson_uart.c | 5 ++--
drivers/tty/serial/mps2-uart.c | 5 ++--
drivers/tty/serial/pmac_zilog.c | 8 ++----
drivers/tty/serial/vt8500_serial.c | 4 +--
drivers/tty/serial/xilinx_uartps.c | 3 +--
drivers/tty/serial/zs.c | 10 +++++---
include/linux/serial_core.h | 40 +++++++++++++++++++++++++++++
14 files changed, 76 insertions(+), 39 deletions(-)
diff --git a/drivers/tty/serial/8250/8250_acorn.c b/drivers/tty/serial/8250/8250_acorn.c
index 758c4aa..359171b 100644
--- a/drivers/tty/serial/8250/8250_acorn.c
+++ b/drivers/tty/serial/8250/8250_acorn.c
@@ -63,14 +63,15 @@ struct serial_card_info {
uart.port.irq = ec->irq;
uart.port.flags = UPF_BOOT_AUTOCONF | UPF_SHARE_IRQ;
uart.port.uartclk = type->uartclk;
- uart.port.iotype = UPIO_MEM;
uart.port.regshift = 2;
uart.port.dev = &ec->dev;
for (i = 0; i < info->num_ports; i++) {
uart.port.membase = info->vaddr + type->offset[i];
- uart.port.mapbase = bus_addr + type->offset[i];
+ /* mapsize is computed by serial8250_register_8250_port() */
+ uart_memres_set_start_len(&uart.port,
+ bus_addr + type->offset[i], 0);
info->ports[i] = serial8250_register_8250_port(&uart);
}
diff --git a/drivers/tty/serial/8250/8250_aspeed_vuart.c b/drivers/tty/serial/8250/8250_aspeed_vuart.c
index 0438d9a..0e06391 100644
--- a/drivers/tty/serial/8250/8250_aspeed_vuart.c
+++ b/drivers/tty/serial/8250/8250_aspeed_vuart.c
@@ -328,8 +328,6 @@ static int aspeed_vuart_probe(struct platform_device *pdev)
memset(&port, 0, sizeof(port));
port.port.private_data = vuart;
port.port.membase = vuart->regs;
- port.port.mapbase = res->start;
- port.port.mapsize = resource_size(res);
port.port.startup = aspeed_vuart_startup;
port.port.shutdown = aspeed_vuart_shutdown;
port.port.throttle = aspeed_vuart_throttle;
@@ -337,6 +335,8 @@ static int aspeed_vuart_probe(struct platform_device *pdev)
port.port.status = UPSTAT_SYNC_FIFO;
port.port.dev = &pdev->dev;
+ uart_memres_set_res(&port.port, res);
+
rc = sysfs_create_group(&vuart->dev->kobj, &aspeed_vuart_attr_group);
if (rc < 0)
return rc;
diff --git a/drivers/tty/serial/8250/8250_dw.c b/drivers/tty/serial/8250/8250_dw.c
index d31b975..cb65256 100644
--- a/drivers/tty/serial/8250/8250_dw.c
+++ b/drivers/tty/serial/8250/8250_dw.c
@@ -513,18 +513,17 @@ static int dw8250_probe(struct platform_device *pdev)
}
spin_lock_init(&p->lock);
- p->mapbase = regs->start;
p->irq = irq;
p->handle_irq = dw8250_handle_irq;
p->pm = dw8250_do_pm;
p->type = PORT_8250;
p->flags = UPF_SHARE_IRQ | UPF_FIXED_PORT;
p->dev = dev;
- p->iotype = UPIO_MEM;
p->serial_in = dw8250_serial_in;
p->serial_out = dw8250_serial_out;
p->set_ldisc = dw8250_set_ldisc;
p->set_termios = dw8250_set_termios;
+ uart_memres_set_res(p, regs);
p->membase = devm_ioremap(dev, regs->start, resource_size(regs));
if (!p->membase)
diff --git a/drivers/tty/serial/8250/8250_em.c b/drivers/tty/serial/8250/8250_em.c
index 2a76e22..7610441 100644
--- a/drivers/tty/serial/8250/8250_em.c
+++ b/drivers/tty/serial/8250/8250_em.c
@@ -100,12 +100,12 @@ static int serial8250_em_probe(struct platform_device *pdev)
}
memset(&up, 0, sizeof(up));
- up.port.mapbase = regs->start;
up.port.irq = irq->start;
up.port.type = PORT_UNKNOWN;
up.port.flags = UPF_BOOT_AUTOCONF | UPF_FIXED_PORT | UPF_IOREMAP;
up.port.dev = &pdev->dev;
up.port.private_data = priv;
+ uart_memres_set_res(&up.port, res);
clk_prepare_enable(priv->sclk);
up.port.uartclk = clk_get_rate(priv->sclk);
diff --git a/drivers/tty/serial/8250/8250_exar.c b/drivers/tty/serial/8250/8250_exar.c
index 0089aa3..f4c1289 100644
--- a/drivers/tty/serial/8250/8250_exar.c
+++ b/drivers/tty/serial/8250/8250_exar.c
@@ -134,8 +134,10 @@ static int default_setup(struct exar8250 *priv, struct pci_dev *pcidev,
const struct exar8250_board *board = priv->board;
unsigned int bar = 0;
- port->port.iotype = UPIO_MEM;
- port->port.mapbase = pci_resource_start(pcidev, bar) + offset;
+ uart_memres_set_start_len(&port->port,
+ pci_resource_start(pcidev, bar) + offset,
+ pci_resource_len(pcidev, bar));
+
port->port.membase = priv->virt + offset;
port->port.regshift = board->reg_shift;
diff --git a/drivers/tty/serial/8250/8250_hp300.c b/drivers/tty/serial/8250/8250_hp300.c
index 3012ea0..09f9dd3 100644
--- a/drivers/tty/serial/8250/8250_hp300.c
+++ b/drivers/tty/serial/8250/8250_hp300.c
@@ -114,7 +114,9 @@ int __init hp300_setup_serial_console(void)
pr_info("Serial console is HP APCI 1\n");
port.uartclk = HPAPCI_BAUD_BASE * 16;
- port.mapbase = (FRODO_BASE + FRODO_APCI_OFFSET(1));
+ uart_memres_set_start_len(
+ &port,
+ FRODO_BASE + FRODO_APCI_OFFSET(1), 0);
port.membase = (char *)(port.mapbase + DIO_VIRADDRBASE);
port.regshift = 2;
add_preferred_console("ttyS", port.line, "9600n8");
@@ -131,7 +133,8 @@ int __init hp300_setup_serial_console(void)
pr_info("Serial console is HP DCA at select code %d\n", scode);
port.uartclk = HPDCA_BAUD_BASE * 16;
- port.mapbase = (pa + UART_OFFSET);
+
+ uart_memres_set_start_len(&port, (pa + UART_OFFSET));
port.membase = (char *)(port.mapbase + DIO_VIRADDRBASE);
port.regshift = 1;
port.irq = DIO_IPL(pa + DIO_VIRADDRBASE);
@@ -173,7 +176,9 @@ static int hpdca_init_one(struct dio_dev *d,
uart.port.flags = UPF_SKIP_TEST | UPF_SHARE_IRQ | UPF_BOOT_AUTOCONF;
uart.port.irq = d->ipl;
uart.port.uartclk = HPDCA_BAUD_BASE * 16;
- uart.port.mapbase = (d->resource.start + UART_OFFSET);
+ uart_memres_set_start_len(&uart.port,
+ (d->resource.start + UART_OFFSET),
+ resource_size(&d->resource));
uart.port.membase = (char *)(uart.port.mapbase + DIO_VIRADDRBASE);
uart.port.regshift = 1;
uart.port.dev = &d->dev;
diff --git a/drivers/tty/serial/8250/8250_of.c b/drivers/tty/serial/8250/8250_of.c
index 08157a1..1c5896c 100644
--- a/drivers/tty/serial/8250/8250_of.c
+++ b/drivers/tty/serial/8250/8250_of.c
@@ -96,18 +96,13 @@ static int of_platform_serial_setup(struct platform_device *ofdev,
UPF_FIXED_TYPE;
spin_lock_init(&port->lock);
- if (resource_type(&resource) == IORESOURCE_IO) {
- port->iotype = UPIO_PORT;
- port->iobase = resource.start;
- } else {
- port->mapbase = resource.start;
- port->mapsize = resource_size(&resource);
+ uart_memres_set_res(port, &resource);
+ if (resource_type(&resource) == IORESOURCE_MEM) {
/* Check for shifted address mapping */
if (of_property_read_u32(np, "reg-offset", &prop) == 0)
port->mapbase += prop;
- port->iotype = UPIO_MEM;
if (of_property_read_u32(np, "reg-io-width", &prop) == 0) {
switch (prop) {
case 1:
diff --git a/drivers/tty/serial/meson_uart.c b/drivers/tty/serial/meson_uart.c
index fbc5bc0..bfcaa2f 100644
--- a/drivers/tty/serial/meson_uart.c
+++ b/drivers/tty/serial/meson_uart.c
@@ -698,9 +698,8 @@ static int meson_uart_probe(struct platform_device *pdev)
if (ret)
return ret;
- port->iotype = UPIO_MEM;
- port->mapbase = res_mem->start;
- port->mapsize = resource_size(res_mem);
+ uart_memset_set_res(port, res_mem);
+
port->irq = res_irq->start;
port->flags = UPF_BOOT_AUTOCONF | UPF_LOW_LATENCY;
port->dev = &pdev->dev;
diff --git a/drivers/tty/serial/mps2-uart.c b/drivers/tty/serial/mps2-uart.c
index 587b42f..a4fd1de 100644
--- a/drivers/tty/serial/mps2-uart.c
+++ b/drivers/tty/serial/mps2-uart.c
@@ -562,9 +562,8 @@ static int mps2_init_port(struct platform_device *pdev,
if (IS_ERR(mps_port->port.membase))
return PTR_ERR(mps_port->port.membase);
- mps_port->port.mapbase = res->start;
- mps_port->port.mapsize = resource_size(res);
- mps_port->port.iotype = UPIO_MEM;
+ uart_memres_set_res(&mps_port->port, res);
+
mps_port->port.flags = UPF_BOOT_AUTOCONF;
mps_port->port.fifosize = 1;
mps_port->port.ops = &mps2_uart_pops;
diff --git a/drivers/tty/serial/pmac_zilog.c b/drivers/tty/serial/pmac_zilog.c
index 1fef014..7017dd2 100644
--- a/drivers/tty/serial/pmac_zilog.c
+++ b/drivers/tty/serial/pmac_zilog.c
@@ -1412,8 +1412,7 @@ static int __init pmz_init_port(struct uart_pmac_port *uap)
*/
if (of_address_to_resource(np, 0, &r_ports))
return -ENODEV;
- uap->port.mapbase = r_ports.start;
- uap->port.mapsize = PMZ_MAPSIZE;
+ uart_memres_set_start_len(&uap->port, r_ports.start, PMZ_MAPSIZE);
uap->port.membase = ioremap(uap->port.mapbase, uap->port.mapsize);
uap->control_reg = uap->port.membase;
@@ -1493,7 +1492,6 @@ static int __init pmz_init_port(struct uart_pmac_port *uap)
/*
* Init remaining bits of "port" structure
*/
- uap->port.iotype = UPIO_MEM;
uap->port.irq = irq_of_parse_and_map(np, 0);
uap->port.uartclk = ZS_CLOCK;
uap->port.fifosize = 1;
@@ -1711,10 +1709,8 @@ static int __init pmz_init_port(struct uart_pmac_port *uap)
if (!r_ports || irq <= 0)
return -ENODEV;
- uap->port.mapbase = r_ports->start;
- uap->port.mapsize = PMZ_MAPSIZE;
+ uart_memres_set_start_len(&uap->port, r_ports->start, PMZ_MAPSIZE);
uap->port.membase = (unsigned char __iomem *) r_ports->start;
- uap->port.iotype = UPIO_MEM;
uap->port.irq = irq;
uap->port.uartclk = ZS_CLOCK;
uap->port.fifosize = 1;
diff --git a/drivers/tty/serial/vt8500_serial.c b/drivers/tty/serial/vt8500_serial.c
index 3d58e9b..b303de4 100644
--- a/drivers/tty/serial/vt8500_serial.c
+++ b/drivers/tty/serial/vt8500_serial.c
@@ -695,8 +695,6 @@ static int vt8500_serial_probe(struct platform_device *pdev)
VT8500_RECOMMENDED_CLK
);
vt8500_port->uart.type = PORT_VT8500;
- vt8500_port->uart.iotype = UPIO_MEM;
- vt8500_port->uart.mapbase = mmres->start;
vt8500_port->uart.irq = irqres->start;
vt8500_port->uart.fifosize = 16;
vt8500_port->uart.ops = &vt8500_uart_pops;
@@ -704,6 +702,8 @@ static int vt8500_serial_probe(struct platform_device *pdev)
vt8500_port->uart.dev = &pdev->dev;
vt8500_port->uart.flags = UPF_IOREMAP | UPF_BOOT_AUTOCONF;
+ uart_memres_set_res(&vt8500_port->uart, mmres);
+
/* Serial core uses the magic "16" everywhere - adjust for it */
vt8500_port->uart.uartclk = 16 * clk_get_rate(vt8500_port->clk) /
vt8500_port->clk_predivisor /
diff --git a/drivers/tty/serial/xilinx_uartps.c b/drivers/tty/serial/xilinx_uartps.c
index cf8ca66..895c90c 100644
--- a/drivers/tty/serial/xilinx_uartps.c
+++ b/drivers/tty/serial/xilinx_uartps.c
@@ -1626,8 +1626,7 @@ static int cdns_uart_probe(struct platform_device *pdev)
* This function also registers this device with the tty layer
* and triggers invocation of the config_port() entry point.
*/
- port->mapbase = res->start;
- port->mapsize = CDNS_UART_REGISTER_SPACE;
+ uart_memres_set_start_len(res->start, CDNS_UART_REGISTER_SPACE);
port->irq = irq;
port->dev = &pdev->dev;
port->uartclk = clk_get_rate(cdns_uart_data->uartclk);
diff --git a/drivers/tty/serial/zs.c b/drivers/tty/serial/zs.c
index ab432ba..87990b1 100644
--- a/drivers/tty/serial/zs.c
+++ b/drivers/tty/serial/zs.c
@@ -1113,10 +1113,12 @@ static int __init zs_probe_sccs(void)
uport->flags = UPF_BOOT_AUTOCONF;
uport->ops = &zs_ops;
uport->line = chip * ZS_NUM_CHAN + side;
- uport->mapsize = ZS_CHAN_IO_SIZE;
- uport->mapbase = dec_kn_slot_base +
- zs_parms.scc[chip] +
- (side ^ ZS_CHAN_B) * ZS_CHAN_IO_SIZE;
+
+ uart_memres_set_start_len(dec_kn_slot_base +
+ zs_parms.scc[chip] +
+ (side ^ ZS_CHAN_B) *
+ ZS_CHAN_IO_SIZE,
+ ZS_CHAN_IO_SIZE);
for (i = 0; i < ZS_NUM_REGS; i++)
zport->regs[i] = zs_init_regs[i];
diff --git a/include/linux/serial_core.h b/include/linux/serial_core.h
index 5fe2b03..d891c8d 100644
--- a/include/linux/serial_core.h
+++ b/include/linux/serial_core.h
@@ -427,6 +427,46 @@ void uart_console_write(struct uart_port *port, const char *s,
int uart_match_port(struct uart_port *port1, struct uart_port *port2);
/*
+ * set physical io range from struct resource
+ * if resource is NULL, clear the fields
+ * also set the iotype to UPIO_MEM
+ */
+static inline void uart_memres_set_res(struct uart_port *port,
+ struct resource *res)
+{
+ if (!res) {
+ port->mapsize = 0;
+ port->mapbase = 0;
+ port->iobase = 0;
+ return;
+ }
+
+ if (resource_type(res) == IORESOURCE_IO) {
+ port->iotype = UPIO_PORT;
+ port->iobase = resource->start;
+ return;
+ }
+
+ uart->mapbase = res->start;
+ uart->mapsize = resource_size(res);
+ uart->iotype = UPIO_MEM;
+}
+
+/*
+ * set physical io range by start address and length
+ * if resource is NULL, clear the fields
+ * also set the iotype to UPIO_MEM
+ */
+static inline void uart_memres_set_start_len(struct uart_driver *uart,
+ resource_size_t start,
+ resource_size_t len)
+{
+ uart->mapbase = start;
+ uart->mapsize = len;
+ uart->iotype = UPIO_MEM;
+}
+
+/*
* Power Management
*/
int uart_suspend_port(struct uart_driver *reg, struct uart_port *port);
--
1.9.1
More information about the Linuxppc-dev
mailing list