[PATCH v4 20/63] Documentation: ACPI: move apei/einj.txt to firmware-guide/acpi and convert to reST
Mauro Carvalho Chehab
mchehab+samsung at kernel.org
Thu Apr 25 00:33:49 AEST 2019
Em Wed, 24 Apr 2019 00:28:49 +0800
Changbin Du <changbin.du at gmail.com> escreveu:
> This converts the plain text documentation to reStructuredText format and
> add it to Sphinx TOC tree. No essential content change.
>
> Signed-off-by: Changbin Du <changbin.du at gmail.com>
> ---
> .../acpi/apei/einj.rst} | 98 ++++++++++---------
> Documentation/firmware-guide/acpi/index.rst | 1 +
> 2 files changed, 53 insertions(+), 46 deletions(-)
> rename Documentation/{acpi/apei/einj.txt => firmware-guide/acpi/apei/einj.rst} (67%)
>
> diff --git a/Documentation/acpi/apei/einj.txt b/Documentation/firmware-guide/acpi/apei/einj.rst
> similarity index 67%
> rename from Documentation/acpi/apei/einj.txt
> rename to Documentation/firmware-guide/acpi/apei/einj.rst
> index e550c8b98139..d85e2667155c 100644
> --- a/Documentation/acpi/apei/einj.txt
> +++ b/Documentation/firmware-guide/acpi/apei/einj.rst
> @@ -1,13 +1,16 @@
> - APEI Error INJection
> - ~~~~~~~~~~~~~~~~~~~~
> +.. SPDX-License-Identifier: GPL-2.0
> +
> +====================
> +APEI Error INJection
> +====================
>
> EINJ provides a hardware error injection mechanism. It is very useful
> for debugging and testing APEI and RAS features in general.
>
> You need to check whether your BIOS supports EINJ first. For that, look
> -for early boot messages similar to this one:
> +for early boot messages similar to this one::
>
> -ACPI: EINJ 0x000000007370A000 000150 (v01 INTEL 00000001 INTL 00000001)
> + ACPI: EINJ 0x000000007370A000 000150 (v01 INTEL 00000001 INTL 00000001)
>
> which shows that the BIOS is exposing an EINJ table - it is the
> mechanism through which the injection is done.
> @@ -23,11 +26,11 @@ order to see the APEI,EINJ,... functionality supported and exposed by
> the BIOS menu.
>
> To use EINJ, make sure the following are options enabled in your kernel
> -configuration:
> +configuration::
>
> -CONFIG_DEBUG_FS
> -CONFIG_ACPI_APEI
> -CONFIG_ACPI_APEI_EINJ
> + CONFIG_DEBUG_FS
> + CONFIG_ACPI_APEI
> + CONFIG_ACPI_APEI_EINJ
>
> The EINJ user interface is in <debugfs mount point>/apei/einj.
>
> @@ -35,22 +38,22 @@ The following files belong to it:
>
> - available_error_type
>
> - This file shows which error types are supported:
> -
> - Error Type Value Error Description
> - ================ =================
> - 0x00000001 Processor Correctable
> - 0x00000002 Processor Uncorrectable non-fatal
> - 0x00000004 Processor Uncorrectable fatal
> - 0x00000008 Memory Correctable
> - 0x00000010 Memory Uncorrectable non-fatal
> - 0x00000020 Memory Uncorrectable fatal
> - 0x00000040 PCI Express Correctable
> - 0x00000080 PCI Express Uncorrectable fatal
> - 0x00000100 PCI Express Uncorrectable non-fatal
> - 0x00000200 Platform Correctable
> - 0x00000400 Platform Uncorrectable non-fatal
> - 0x00000800 Platform Uncorrectable fatal
> + This file shows which error types are supported::
> +
> + Error Type Value Error Description
> + ================ =================
> + 0x00000001 Processor Correctable
> + 0x00000002 Processor Uncorrectable non-fatal
> + 0x00000004 Processor Uncorrectable fatal
> + 0x00000008 Memory Correctable
> + 0x00000010 Memory Uncorrectable non-fatal
> + 0x00000020 Memory Uncorrectable fatal
> + 0x00000040 PCI Express Correctable
> + 0x00000080 PCI Express Uncorrectable fatal
> + 0x00000100 PCI Express Uncorrectable non-fatal
> + 0x00000200 Platform Correctable
> + 0x00000400 Platform Uncorrectable non-fatal
> + 0x00000800 Platform Uncorrectable fatal
This is a table and not a literal block.
The best here to preserve the author's intent is to just adjust the table
markups in order to make it parseable, e. g.:
This file shows which error types are supported:
================ ===================================
Error Type Value Error Description
================ ===================================
0x00000001 Processor Correctable
0x00000002 Processor Uncorrectable non-fatal
0x00000004 Processor Uncorrectable fatal
0x00000008 Memory Correctable
0x00000010 Memory Uncorrectable non-fatal
0x00000020 Memory Uncorrectable fatal
0x00000040 PCI Express Correctable
0x00000080 PCI Express Uncorrectable fatal
0x00000100 PCI Express Uncorrectable non-fatal
0x00000200 Platform Correctable
0x00000400 Platform Uncorrectable non-fatal
0x00000800 Platform Uncorrectable fatal
================ ===================================
After such change:
Reviewed-by: Mauro Carvalho Chehab <mchehab+samsung at kernel.org>
>
> The format of the file contents are as above, except present are only
> the available error types.
> @@ -73,9 +76,12 @@ The following files belong to it:
> injection. Value is a bitmask as specified in ACPI5.0 spec for the
> SET_ERROR_TYPE_WITH_ADDRESS data structure:
>
> - Bit 0 - Processor APIC field valid (see param3 below).
> - Bit 1 - Memory address and mask valid (param1 and param2).
> - Bit 2 - PCIe (seg,bus,dev,fn) valid (see param4 below).
> + Bit 0
> + Processor APIC field valid (see param3 below).
> + Bit 1
> + Memory address and mask valid (param1 and param2).
> + Bit 2
> + PCIe (seg,bus,dev,fn) valid (see param4 below).
>
> If set to zero, legacy behavior is mimicked where the type of
> injection specifies just one bit set, and param1 is multiplexed.
> @@ -121,7 +127,7 @@ BIOS versions based on the ACPI 5.0 specification have more control over
> the target of the injection. For processor-related errors (type 0x1, 0x2
> and 0x4), you can set flags to 0x3 (param3 for bit 0, and param1 and
> param2 for bit 1) so that you have more information added to the error
> -signature being injected. The actual data passed is this:
> +signature being injected. The actual data passed is this::
>
> memory_address = param1;
> memory_address_range = param2;
> @@ -131,7 +137,7 @@ signature being injected. The actual data passed is this:
> For memory errors (type 0x8, 0x10 and 0x20) the address is set using
> param1 with a mask in param2 (0x0 is equivalent to all ones). For PCI
> express errors (type 0x40, 0x80 and 0x100) the segment, bus, device and
> -function are specified using param1:
> +function are specified using param1::
>
> 31 24 23 16 15 11 10 8 7 0
> +-------------------------------------------------+
> @@ -152,26 +158,26 @@ documentation for details (and expect changes to this API if vendors
> creativity in using this feature expands beyond our expectations).
>
>
> -An error injection example:
> +An error injection example::
>
> -# cd /sys/kernel/debug/apei/einj
> -# cat available_error_type # See which errors can be injected
> -0x00000002 Processor Uncorrectable non-fatal
> -0x00000008 Memory Correctable
> -0x00000010 Memory Uncorrectable non-fatal
> -# echo 0x12345000 > param1 # Set memory address for injection
> -# echo $((-1 << 12)) > param2 # Mask 0xfffffffffffff000 - anywhere in this page
> -# echo 0x8 > error_type # Choose correctable memory error
> -# echo 1 > error_inject # Inject now
> + # cd /sys/kernel/debug/apei/einj
> + # cat available_error_type # See which errors can be injected
> + 0x00000002 Processor Uncorrectable non-fatal
> + 0x00000008 Memory Correctable
> + 0x00000010 Memory Uncorrectable non-fatal
> + # echo 0x12345000 > param1 # Set memory address for injection
> + # echo $((-1 << 12)) > param2 # Mask 0xfffffffffffff000 - anywhere in this page
> + # echo 0x8 > error_type # Choose correctable memory error
> + # echo 1 > error_inject # Inject now
>
> -You should see something like this in dmesg:
> +You should see something like this in dmesg::
>
> -[22715.830801] EDAC sbridge MC3: HANDLING MCE MEMORY ERROR
> -[22715.834759] EDAC sbridge MC3: CPU 0: Machine Check Event: 0 Bank 7: 8c00004000010090
> -[22715.834759] EDAC sbridge MC3: TSC 0
> -[22715.834759] EDAC sbridge MC3: ADDR 12345000 EDAC sbridge MC3: MISC 144780c86
> -[22715.834759] EDAC sbridge MC3: PROCESSOR 0:306e7 TIME 1422553404 SOCKET 0 APIC 0
> -[22716.616173] EDAC MC3: 1 CE memory read error on CPU_SrcID#0_Channel#0_DIMM#0 (channel:0 slot:0 page:0x12345 offset:0x0 grain:32 syndrome:0x0 - area:DRAM err_code:0001:0090 socket:0 channel_mask:1 rank:0)
> + [22715.830801] EDAC sbridge MC3: HANDLING MCE MEMORY ERROR
> + [22715.834759] EDAC sbridge MC3: CPU 0: Machine Check Event: 0 Bank 7: 8c00004000010090
> + [22715.834759] EDAC sbridge MC3: TSC 0
> + [22715.834759] EDAC sbridge MC3: ADDR 12345000 EDAC sbridge MC3: MISC 144780c86
> + [22715.834759] EDAC sbridge MC3: PROCESSOR 0:306e7 TIME 1422553404 SOCKET 0 APIC 0
> + [22716.616173] EDAC MC3: 1 CE memory read error on CPU_SrcID#0_Channel#0_DIMM#0 (channel:0 slot:0 page:0x12345 offset:0x0 grain:32 syndrome:0x0 - area:DRAM err_code:0001:0090 socket:0 channel_mask:1 rank:0)
>
> For more information about EINJ, please refer to ACPI specification
> version 4.0, section 17.5 and ACPI 5.0, section 18.6.
> diff --git a/Documentation/firmware-guide/acpi/index.rst b/Documentation/firmware-guide/acpi/index.rst
> index 869badba6d7a..fca854f017d8 100644
> --- a/Documentation/firmware-guide/acpi/index.rst
> +++ b/Documentation/firmware-guide/acpi/index.rst
> @@ -18,6 +18,7 @@ ACPI Support
> debug
> aml-debugger
> apei/output_format
> + apei/einj
> gpio-properties
> i2c-muxes
> acpi-lid
Thanks,
Mauro
More information about the Linuxppc-dev
mailing list