[PATCH v3 5/6] arm64: dts: add QorIQ LX2160A SoC support
Li Yang
leoyang.li at nxp.com
Sat Sep 29 06:41:18 AEST 2018
On Mon, Sep 24, 2018 at 7:47 AM Vabhav Sharma <vabhav.sharma at nxp.com> wrote:
>
> LX2160A SoC is based on Layerscape Chassis Generation 3.2 Architecture.
>
> LX2160A features an advanced 16 64-bit ARM v8 CortexA72 processor cores
> in 8 cluster, CCN508, GICv3,two 64-bit DDR4 memory controller, 8 I2C
> controllers, 3 dspi, 2 esdhc,2 USB 3.0, mmu 500, 3 SATA, 4 PL011 SBSA
> UARTs etc.
>
> Signed-off-by: Ramneek Mehresh <ramneek.mehresh at nxp.com>
> Signed-off-by: Zhang Ying-22455 <ying.zhang22455 at nxp.com>
> Signed-off-by: Nipun Gupta <nipun.gupta at nxp.com>
> Signed-off-by: Priyanka Jain <priyanka.jain at nxp.com>
> Signed-off-by: Yogesh Gaur <yogeshnarayan.gaur at nxp.com>
> Signed-off-by: Sriram Dash <sriram.dash at nxp.com>
> Signed-off-by: Vabhav Sharma <vabhav.sharma at nxp.com>
> ---
> arch/arm64/boot/dts/freescale/fsl-lx2160a.dtsi | 693 +++++++++++++++++++++++++
> 1 file changed, 693 insertions(+)
> create mode 100644 arch/arm64/boot/dts/freescale/fsl-lx2160a.dtsi
>
> diff --git a/arch/arm64/boot/dts/freescale/fsl-lx2160a.dtsi b/arch/arm64/boot/dts/freescale/fsl-lx2160a.dtsi
> new file mode 100644
> index 0000000..46eea16
> --- /dev/null
> +++ b/arch/arm64/boot/dts/freescale/fsl-lx2160a.dtsi
> @@ -0,0 +1,693 @@
> +// SPDX-License-Identifier: (GPL-2.0 OR MIT)
> +//
> +// Device Tree Include file for Layerscape-LX2160A family SoC.
> +//
> +// Copyright 2018 NXP
> +
> +#include <dt-bindings/interrupt-controller/arm-gic.h>
You included the header file, but you didn't use the MACROs in most of
the interrupts property below. It is recommended to use them for
better readibity.
> +
> +/memreserve/ 0x80000000 0x00010000;
> +
> +/ {
> + compatible = "fsl,lx2160a";
> + interrupt-parent = <&gic>;
> + #address-cells = <2>;
> + #size-cells = <2>;
> +
> + cpus {
> + #address-cells = <1>;
> + #size-cells = <0>;
> +
> + // 8 clusters having 2 Cortex-A72 cores each
> + cpu at 0 {
> + device_type = "cpu";
> + compatible = "arm,cortex-a72";
> + reg = <0x0>;
> + clocks = <&clockgen 1 0>;
> + d-cache-size = <0x8000>;
> + d-cache-line-size = <64>;
> + d-cache-sets = <128>;
> + i-cache-size = <0xC000>;
> + i-cache-line-size = <64>;
> + i-cache-sets = <192>;
> + next-level-cache = <&cluster0_l2>;
enable-method is a required property for this and cpu below.
> + };
> +
> + cpu at 1 {
> + device_type = "cpu";
> + compatible = "arm,cortex-a72";
> + reg = <0x1>;
> + clocks = <&clockgen 1 0>;
> + d-cache-size = <0x8000>;
> + d-cache-line-size = <64>;
> + d-cache-sets = <128>;
> + i-cache-size = <0xC000>;
> + i-cache-line-size = <64>;
> + i-cache-sets = <192>;
> + next-level-cache = <&cluster0_l2>;
> + };
> +
> + cpu at 100 {
> + device_type = "cpu";
> + compatible = "arm,cortex-a72";
> + reg = <0x100>;
> + clocks = <&clockgen 1 1>;
> + d-cache-size = <0x8000>;
> + d-cache-line-size = <64>;
> + d-cache-sets = <128>;
> + i-cache-size = <0xC000>;
> + i-cache-line-size = <64>;
> + i-cache-sets = <192>;
> + next-level-cache = <&cluster1_l2>;
> + };
> +
> + cpu at 101 {
> + device_type = "cpu";
> + compatible = "arm,cortex-a72";
> + reg = <0x101>;
> + clocks = <&clockgen 1 1>;
> + d-cache-size = <0x8000>;
> + d-cache-line-size = <64>;
> + d-cache-sets = <128>;
> + i-cache-size = <0xC000>;
> + i-cache-line-size = <64>;
> + i-cache-sets = <192>;
> + next-level-cache = <&cluster1_l2>;
> + };
> +
> + cpu at 200 {
> + device_type = "cpu";
> + compatible = "arm,cortex-a72";
> + reg = <0x200>;
> + clocks = <&clockgen 1 2>;
> + d-cache-size = <0x8000>;
> + d-cache-line-size = <64>;
> + d-cache-sets = <128>;
> + i-cache-size = <0xC000>;
> + i-cache-line-size = <64>;
> + i-cache-sets = <192>;
> + next-level-cache = <&cluster2_l2>;
> + };
> +
> + cpu at 201 {
> + device_type = "cpu";
> + compatible = "arm,cortex-a72";
> + reg = <0x201>;
> + clocks = <&clockgen 1 2>;
> + d-cache-size = <0x8000>;
> + d-cache-line-size = <64>;
> + d-cache-sets = <128>;
> + i-cache-size = <0xC000>;
> + i-cache-line-size = <64>;
> + i-cache-sets = <192>;
> + next-level-cache = <&cluster2_l2>;
> + };
> +
> + cpu at 300 {
> + device_type = "cpu";
> + compatible = "arm,cortex-a72";
> + reg = <0x300>;
> + clocks = <&clockgen 1 3>;
> + d-cache-size = <0x8000>;
> + d-cache-line-size = <64>;
> + d-cache-sets = <128>;
> + i-cache-size = <0xC000>;
> + i-cache-line-size = <64>;
> + i-cache-sets = <192>;
> + next-level-cache = <&cluster3_l2>;
> + };
> +
> + cpu at 301 {
> + device_type = "cpu";
> + compatible = "arm,cortex-a72";
> + reg = <0x301>;
> + clocks = <&clockgen 1 3>;
> + d-cache-size = <0x8000>;
> + d-cache-line-size = <64>;
> + d-cache-sets = <128>;
> + i-cache-size = <0xC000>;
> + i-cache-line-size = <64>;
> + i-cache-sets = <192>;
> + next-level-cache = <&cluster3_l2>;
> + };
> +
> + cpu at 400 {
> + device_type = "cpu";
> + compatible = "arm,cortex-a72";
> + reg = <0x400>;
> + clocks = <&clockgen 1 4>;
> + d-cache-size = <0x8000>;
> + d-cache-line-size = <64>;
> + d-cache-sets = <128>;
> + i-cache-size = <0xC000>;
> + i-cache-line-size = <64>;
> + i-cache-sets = <192>;
> + next-level-cache = <&cluster4_l2>;
> + };
> +
> + cpu at 401 {
> + device_type = "cpu";
> + compatible = "arm,cortex-a72";
> + reg = <0x401>;
> + clocks = <&clockgen 1 4>;
> + d-cache-size = <0x8000>;
> + d-cache-line-size = <64>;
> + d-cache-sets = <128>;
> + i-cache-size = <0xC000>;
> + i-cache-line-size = <64>;
> + i-cache-sets = <192>;
> + next-level-cache = <&cluster4_l2>;
> + };
> +
> + cpu at 500 {
> + device_type = "cpu";
> + compatible = "arm,cortex-a72";
> + reg = <0x500>;
> + clocks = <&clockgen 1 5>;
> + d-cache-size = <0x8000>;
> + d-cache-line-size = <64>;
> + d-cache-sets = <128>;
> + i-cache-size = <0xC000>;
> + i-cache-line-size = <64>;
> + i-cache-sets = <192>;
> + next-level-cache = <&cluster5_l2>;
> + };
> +
> + cpu at 501 {
> + device_type = "cpu";
> + compatible = "arm,cortex-a72";
> + reg = <0x501>;
> + clocks = <&clockgen 1 5>;
> + d-cache-size = <0x8000>;
> + d-cache-line-size = <64>;
> + d-cache-sets = <128>;
> + i-cache-size = <0xC000>;
> + i-cache-line-size = <64>;
> + i-cache-sets = <192>;
> + next-level-cache = <&cluster5_l2>;
> + };
> +
> + cpu at 600 {
> + device_type = "cpu";
> + compatible = "arm,cortex-a72";
> + reg = <0x600>;
> + clocks = <&clockgen 1 6>;
> + d-cache-size = <0x8000>;
> + d-cache-line-size = <64>;
> + d-cache-sets = <128>;
> + i-cache-size = <0xC000>;
> + i-cache-line-size = <64>;
> + i-cache-sets = <192>;
> + next-level-cache = <&cluster6_l2>;
> + };
> +
> + cpu at 601 {
> + device_type = "cpu";
> + compatible = "arm,cortex-a72";
> + reg = <0x601>;
> + clocks = <&clockgen 1 6>;
> + d-cache-size = <0x8000>;
> + d-cache-line-size = <64>;
> + d-cache-sets = <128>;
> + i-cache-size = <0xC000>;
> + i-cache-line-size = <64>;
> + i-cache-sets = <192>;
> + next-level-cache = <&cluster6_l2>;
> + };
> +
> + cpu at 700 {
> + device_type = "cpu";
> + compatible = "arm,cortex-a72";
> + reg = <0x700>;
> + clocks = <&clockgen 1 7>;
> + d-cache-size = <0x8000>;
> + d-cache-line-size = <64>;
> + d-cache-sets = <128>;
> + i-cache-size = <0xC000>;
> + i-cache-line-size = <64>;
> + i-cache-sets = <192>;
> + next-level-cache = <&cluster7_l2>;
> + };
> +
> + cpu at 701 {
> + device_type = "cpu";
> + compatible = "arm,cortex-a72";
> + reg = <0x701>;
> + clocks = <&clockgen 1 7>;
> + d-cache-size = <0x8000>;
> + d-cache-line-size = <64>;
> + d-cache-sets = <128>;
> + i-cache-size = <0xC000>;
> + i-cache-line-size = <64>;
> + i-cache-sets = <192>;
> + next-level-cache = <&cluster7_l2>;
> + };
> +
> + cluster0_l2: l2-cache0 {
> + compatible = "cache";
> + cache-size = <0x100000>;
> + cache-line-size = <64>;
> + cache-sets = <1024>;
> + cache-level = <2>;
> + };
> +
> + cluster1_l2: l2-cache1 {
> + compatible = "cache";
> + cache-size = <0x100000>;
> + cache-line-size = <64>;
> + cache-sets = <1024>;
> + cache-level = <2>;
> + };
> +
> + cluster2_l2: l2-cache2 {
> + compatible = "cache";
> + cache-size = <0x100000>;
> + cache-line-size = <64>;
> + cache-sets = <1024>;
> + cache-level = <2>;
> + };
> +
> + cluster3_l2: l2-cache3 {
> + compatible = "cache";
> + cache-size = <0x100000>;
> + cache-line-size = <64>;
> + cache-sets = <1024>;
> + cache-level = <2>;
> + };
> +
> + cluster4_l2: l2-cache4 {
> + compatible = "cache";
> + cache-size = <0x100000>;
> + cache-line-size = <64>;
> + cache-sets = <1024>;
> + cache-level = <2>;
> + };
> +
> + cluster5_l2: l2-cache5 {
> + compatible = "cache";
> + cache-size = <0x100000>;
> + cache-line-size = <64>;
> + cache-sets = <1024>;
> + cache-level = <2>;
> + };
> +
> + cluster6_l2: l2-cache6 {
> + compatible = "cache";
> + cache-size = <0x100000>;
> + cache-line-size = <64>;
> + cache-sets = <1024>;
> + cache-level = <2>;
> + };
> +
> + cluster7_l2: l2-cache7 {
> + compatible = "cache";
> + cache-size = <0x100000>;
> + cache-line-size = <64>;
> + cache-sets = <1024>;
> + cache-level = <2>;
> + };
> + };
> +
> + gic: interrupt-controller at 6000000 {
> + compatible = "arm,gic-v3";
> + reg = <0x0 0x06000000 0 0x10000>, // GIC Dist
> + <0x0 0x06200000 0 0x200000>, // GICR (RD_base +
> + // SGI_base)
> + <0x0 0x0c0c0000 0 0x2000>, // GICC
> + <0x0 0x0c0d0000 0 0x1000>, // GICH
> + <0x0 0x0c0e0000 0 0x20000>; // GICV
> + #interrupt-cells = <3>;
> + #address-cells = <2>;
> + #size-cells = <2>;
> + ranges;
> + interrupt-controller;
> + interrupts = <1 9 0x4>;
> +
> + its: gic-its at 6020000 {
> + compatible = "arm,gic-v3-its";
> + msi-controller;
> + reg = <0x0 0x6020000 0 0x20000>;
> + };
> + };
> +
> + rstcr: syscon at 1e60000 {
> + compatible = "syscon";
> + reg = <0x0 0x1e60000 0x0 0x4>;
> + };
This is no use if you don't have a syscon-reboot node pointing to it.
> +
> + timer {
> + compatible = "arm,armv8-timer";
> + interrupts = <1 13 4>,
> + <1 14 4>,
> + <1 11 4>,
> + <1 10 4>;
> + };
> +
> + pmu {
> + compatible = "arm,cortex-a72-pmu";
> + interrupts = <1 7 0x8>; // PMU PPI, Level low type
> + };
> +
> + psci {
> + compatible = "arm,psci-0.2";
> + method = "smc";
> + };
> +
> + memory at 80000000 {
> + // DRAM space - 1, size : 2 GB DRAM
> + device_type = "memory";
> + reg = <0x00000000 0x80000000 0 0x80000000>;
> + };
> +
> + ddr1: memory-controller at 1080000 {
> + compatible = "fsl,qoriq-memory-controller";
> + reg = <0x0 0x1080000 0x0 0x1000>;
> + interrupts = <0 17 0x4>;
> + little-endian;
> + };
> +
> + ddr2: memory-controller at 1090000 {
> + compatible = "fsl,qoriq-memory-controller";
> + reg = <0x0 0x1090000 0x0 0x1000>;
> + interrupts = <0 18 0x4>;
> + little-endian;
> + };
> +
> + sysclk: sysclk {
> + compatible = "fixed-clock";
> + #clock-cells = <0>;
> + clock-frequency = <100000000>;
> + clock-output-names = "sysclk";
> + };
> +
> + soc {
> + compatible = "simple-bus";
> + #address-cells = <2>;
> + #size-cells = <2>;
> + ranges;
> +
> + clockgen: clocking at 1300000 {
> + compatible = "fsl,lx2160a-clockgen";
Also update the binding to include this new compatible.
> + reg = <0 0x1300000 0 0xa0000>;
> + #clock-cells = <2>;
> + clocks = <&sysclk>;
> + };
> +
> + crypto: crypto at 8000000 {
> + compatible = "fsl,sec-v5.0", "fsl,sec-v4.0";
> + fsl,sec-era = <10>;
> + #address-cells = <1>;
> + #size-cells = <1>;
> + ranges = <0x0 0x00 0x8000000 0x100000>;
> + reg = <0x00 0x8000000 0x0 0x100000>;
> + interrupts = <GIC_SPI 139 IRQ_TYPE_LEVEL_HIGH>;
> + dma-coherent;
> + status = "disabled";
> +
> + sec_jr0: jr at 10000 {
> + compatible = "fsl,sec-v5.0-job-ring",
> + "fsl,sec-v4.0-job-ring";
> + reg = <0x10000 0x10000>;
> + interrupts = <GIC_SPI 140 IRQ_TYPE_LEVEL_HIGH>;
> + };
> +
> + sec_jr1: jr at 20000 {
> + compatible = "fsl,sec-v5.0-job-ring",
> + "fsl,sec-v4.0-job-ring";
> + reg = <0x20000 0x10000>;
> + interrupts = <GIC_SPI 141 IRQ_TYPE_LEVEL_HIGH>;
> + };
> +
> + sec_jr2: jr at 30000 {
> + compatible = "fsl,sec-v5.0-job-ring",
> + "fsl,sec-v4.0-job-ring";
> + reg = <0x30000 0x10000>;
> + interrupts = <GIC_SPI 142 IRQ_TYPE_LEVEL_HIGH>;
> + };
> +
> + sec_jr3: jr at 40000 {
> + compatible = "fsl,sec-v5.0-job-ring",
> + "fsl,sec-v4.0-job-ring";
> + reg = <0x40000 0x10000>;
> + interrupts = <GIC_SPI 143 IRQ_TYPE_LEVEL_HIGH>;
> + };
> + };
> +
> + dcfg: dcfg at 1e00000 {
> + compatible = "fsl,lx2160a-dcfg", "syscon";
Update the binding to include this new compatible.
> + reg = <0x0 0x1e00000 0x0 0x10000>;
> + little-endian;
> + };
> +
> + gpio0: gpio at 2300000 {
> + compatible = "fsl,qoriq-gpio";
> + reg = <0x0 0x2300000 0x0 0x10000>;
> + interrupts = <0 36 0x4>; // Level high type
> + gpio-controller;
> + little-endian;
> + #gpio-cells = <2>;
> + interrupt-controller;
> + #interrupt-cells = <2>;
> + };
> +
> + gpio1: gpio at 2310000 {
> + compatible = "fsl,qoriq-gpio";
> + reg = <0x0 0x2310000 0x0 0x10000>;
> + interrupts = <0 36 0x4>; // Level high type
> + gpio-controller;
> + little-endian;
> + #gpio-cells = <2>;
> + interrupt-controller;
> + #interrupt-cells = <2>;
> + };
> +
> + gpio2: gpio at 2320000 {
> + compatible = "fsl,qoriq-gpio";
> + reg = <0x0 0x2320000 0x0 0x10000>;
> + interrupts = <0 37 0x4>; // Level high type
> + gpio-controller;
> + little-endian;
> + #gpio-cells = <2>;
> + interrupt-controller;
> + #interrupt-cells = <2>;
> + };
> +
> + gpio3: gpio at 2330000 {
> + compatible = "fsl,qoriq-gpio";
> + reg = <0x0 0x2330000 0x0 0x10000>;
> + interrupts = <0 37 0x4>; // Level high type
> + gpio-controller;
> + little-endian;
> + #gpio-cells = <2>;
> + interrupt-controller;
> + #interrupt-cells = <2>;
> + };
> +
> +
One new line is enough.
> + i2c0: i2c at 2000000 {
> + compatible = "fsl,vf610-i2c";
> + #address-cells = <1>;
> + #size-cells = <0>;
> + reg = <0x0 0x2000000 0x0 0x10000>;
> + interrupts = <0 34 0x4>; // Level high type
> + clock-names = "i2c";
> + clocks = <&clockgen 4 7>;
> + fsl-scl-gpio = <&gpio2 15 0>;
> + status = "disabled";
> + };
> +
> + i2c1: i2c at 2010000 {
> + compatible = "fsl,vf610-i2c";
> + #address-cells = <1>;
> + #size-cells = <0>;
> + reg = <0x0 0x2010000 0x0 0x10000>;
> + interrupts = <0 34 0x4>; // Level high type
> + clock-names = "i2c";
> + clocks = <&clockgen 4 7>;
> + status = "disabled";
> + };
> +
> + i2c2: i2c at 2020000 {
> + compatible = "fsl,vf610-i2c";
> + #address-cells = <1>;
> + #size-cells = <0>;
> + reg = <0x0 0x2020000 0x0 0x10000>;
> + interrupts = <0 35 0x4>; // Level high type
> + clock-names = "i2c";
> + clocks = <&clockgen 4 7>;
> + status = "disabled";
> + };
> +
> + i2c3: i2c at 2030000 {
> + compatible = "fsl,vf610-i2c";
> + #address-cells = <1>;
> + #size-cells = <0>;
> + reg = <0x0 0x2030000 0x0 0x10000>;
> + interrupts = <0 35 0x4>; // Level high type
> + clock-names = "i2c";
> + clocks = <&clockgen 4 7>;
> + status = "disabled";
> + };
> +
> + i2c4: i2c at 2040000 {
> + compatible = "fsl,vf610-i2c";
> + #address-cells = <1>;
> + #size-cells = <0>;
> + reg = <0x0 0x2040000 0x0 0x10000>;
> + interrupts = <0 74 0x4>; // Level high type
> + clock-names = "i2c";
> + clocks = <&clockgen 4 7>;
> + fsl-scl-gpio = <&gpio2 16 0>;
> + status = "disabled";
> + };
> +
> + i2c5: i2c at 2050000 {
> + compatible = "fsl,vf610-i2c";
> + #address-cells = <1>;
> + #size-cells = <0>;
> + reg = <0x0 0x2050000 0x0 0x10000>;
> + interrupts = <0 74 0x4>; // Level high type
> + clock-names = "i2c";
> + clocks = <&clockgen 4 7>;
> + status = "disabled";
> + };
> +
> + i2c6: i2c at 2060000 {
> + compatible = "fsl,vf610-i2c";
> + #address-cells = <1>;
> + #size-cells = <0>;
> + reg = <0x0 0x2060000 0x0 0x10000>;
> + interrupts = <0 75 0x4>; // Level high type
> + clock-names = "i2c";
> + clocks = <&clockgen 4 7>;
> + status = "disabled";
> + };
> +
> + i2c7: i2c at 2070000 {
> + compatible = "fsl,vf610-i2c";
> + #address-cells = <1>;
> + #size-cells = <0>;
> + reg = <0x0 0x2070000 0x0 0x10000>;
> + interrupts = <0 75 0x4>; // Level high type
> + clock-names = "i2c";
> + clocks = <&clockgen 4 7>;
> + status = "disabled";
> + };
> +
> + uart0: serial at 21c0000 {
> + device_type = "serial";
> + compatible = "arm,pl011","arm,sbsa-uart";
>From the sbsa_uart binding:
This UART uses a subset of the PL011 registers and consequently lives
in the PL011 driver. It's baudrate and other communication parameters
cannot be adjusted at runtime, so it lacks a clock specifier here.
So it is a more specific variant of pl011. Put the sbsa-uart compatible first.
> + reg = <0x0 0x21c0000 0x0 0x1000>;
> + interrupts = <0 32 0x4>; // Level high type
> + current-speed = <115200>;
> + status = "disabled";
> + };
> +
> + uart1: serial at 21d0000 {
> + device_type = "serial";
> + compatible = "arm,pl011","arm,sbsa-uart";
> + reg = <0x0 0x21d0000 0x0 0x1000>;
> + interrupts = <0 33 0x4>; // Level high type
> + current-speed = <115200>;
> + status = "disabled";
> + };
> +
> + uart2: serial at 21e0000 {
> + device_type = "serial";
> + compatible = "arm,pl011","arm,sbsa-uart";
> + reg = <0x0 0x21e0000 0x0 0x1000>;
> + interrupts = <0 72 0x4>; // Level high type
> + current-speed = <115200>;
> + status = "disabled";
> + };
> +
> + uart3: serial at 21f0000 {
> + device_type = "serial";
> + compatible = "arm,pl011","arm,sbsa-uart";
> + reg = <0x0 0x21f0000 0x0 0x1000>;
> + interrupts = <0 73 0x4>; // Level high type
> + current-speed = <115200>;
> + status = "disabled";
> + };
> +
> + smmu: iommu at 5000000 {
> + compatible = "arm,mmu-500";
> + reg = <0 0x5000000 0 0x800000>;
> + #iommu-cells = <1>;
> + #global-interrupts = <14>;
> + interrupts = <0 13 4>, // global secure fault
> + <0 14 4>, // combined secure interrupt
> + <0 15 4>, // global non-secure fault
> + <0 16 4>, // combined non-secure interrupt
> + // performance counter interrupts 0-9
> + <0 211 4>, <0 212 4>,
> + <0 213 4>, <0 214 4>,
> + <0 215 4>, <0 216 4>,
> + <0 217 4>, <0 218 4>,
> + <0 219 4>, <0 220 4>,
> + // per context interrupt, 64 interrupts
> + <0 146 4>, <0 147 4>,
> + <0 148 4>, <0 149 4>,
> + <0 150 4>, <0 151 4>,
> + <0 152 4>, <0 153 4>,
> + <0 154 4>, <0 155 4>,
> + <0 156 4>, <0 157 4>,
> + <0 158 4>, <0 159 4>,
> + <0 160 4>, <0 161 4>,
> + <0 162 4>, <0 163 4>,
> + <0 164 4>, <0 165 4>,
> + <0 166 4>, <0 167 4>,
> + <0 168 4>, <0 169 4>,
> + <0 170 4>, <0 171 4>,
> + <0 172 4>, <0 173 4>,
> + <0 174 4>, <0 175 4>,
> + <0 176 4>, <0 177 4>,
> + <0 178 4>, <0 179 4>,
> + <0 180 4>, <0 181 4>,
> + <0 182 4>, <0 183 4>,
> + <0 184 4>, <0 185 4>,
> + <0 186 4>, <0 187 4>,
> + <0 188 4>, <0 189 4>,
> + <0 190 4>, <0 191 4>,
> + <0 192 4>, <0 193 4>,
> + <0 194 4>, <0 195 4>,
> + <0 196 4>, <0 197 4>,
> + <0 198 4>, <0 199 4>,
> + <0 200 4>, <0 201 4>,
> + <0 202 4>, <0 203 4>,
> + <0 204 4>, <0 205 4>,
> + <0 206 4>, <0 207 4>,
> + <0 208 4>, <0 209 4>;
> + dma-coherent;
> + };
> +
> + usb0: usb3 at 3100000 {
> + compatible = "snps,dwc3";
> + reg = <0x0 0x3100000 0x0 0x10000>;
> + interrupts = <0 80 0x4>; // Level high type
> + dr_mode = "host";
> + snps,quirk-frame-length-adjustment = <0x20>;
> + snps,dis_rxdet_inp3_quirk;
> + status = "disabled";
> + };
> +
> + usb1: usb3 at 3110000 {
> + compatible = "snps,dwc3";
> + reg = <0x0 0x3110000 0x0 0x10000>;
> + interrupts = <0 81 0x4>; // Level high type
> + dr_mode = "host";
> + snps,quirk-frame-length-adjustment = <0x20>;
> + snps,dis_rxdet_inp3_quirk;
> + status = "disabled";
> + };
> +
> + watchdog at 23a0000 {
> + compatible = "arm,sbsa-gwdt";
> + reg = <0x0 0x23a0000 0 0x1000>,
> + <0x0 0x2390000 0 0x1000>;
> + interrupts = <0 59 4>;
> + timeout-sec = <30>;
> + };
> +
No new line is needed here.
> + };
> +};
> --
> 2.7.4
>
More information about the Linuxppc-dev
mailing list