[mainline][ppc][bnx2x] watchdog: CPU 80 self-detected hard LOCKUP @ opal_interrupt+0x28/0x70 when module load/unload

[Abdul Haleem]

On Mon, 2018-09-24 at 15:49 +0530, Abdul Haleem wrote:
> On Mon, 2018-09-24 at 19:35 +1000, Oliver wrote:
> > On Mon, Sep 24, 2018 at 6:56 PM, Abdul Haleem
> > <abdhalee at linux.vnet.ibm.com> wrote:
> > > Greeting's
> > >
> > > bnx2x module load/unload test results in continuous hard LOCKUP trace on
> > > my powerpc bare-metal running mainline 4.19.0-rc4 kernel
> > >
> > > the instruction address points to:
> > >
> > > 0xc00000000009d048 is in opal_interrupt
> > > (arch/powerpc/platforms/powernv/opal-irqchip.c:133).
> > > 128
> > > 129     static irqreturn_t opal_interrupt(int irq, void *data)
> > > 130     {
> > > 131             __be64 events;
> > > 132
> > > 133             opal_handle_interrupt(virq_to_hw(irq), &events);
> > > 134             last_outstanding_events = be64_to_cpu(events);
> > > 135             if (opal_have_pending_events())
> > > 136                     opal_wake_poller();
> > > 137
> > >
> > > trace:
> > > bnx2x 0008:01:00.3 enP8p1s0f3: renamed from eth0
> > > bnx2x 0008:01:00.3 enP8p1s0f3: using MSI-X  IRQs: sp 297  fp[0] 299 ... fp[7] 306
> > > bnx2x 0008:01:00.2 enP8p1s0f2: NIC Link is Up, 1000 Mbps full duplex, Flow control: none
> > > bnx2x 0008:01:00.3 enP8p1s0f3: NIC Link is Up, 1000 Mbps full duplex, Flow control: none
> > > bnx2x: QLogic 5771x/578xx 10/20-Gigabit Ethernet Driver bnx2x 1.712.30-0 (2014/02/10)
> > > bnx2x 0008:01:00.0: msix capability found
> > > bnx2x 0008:01:00.0: Using 64-bit DMA iommu bypass
> > > bnx2x 0008:01:00.0: part number 0-0-0-0
> > > bnx2x 0008:01:00.0: 32.000 Gb/s available PCIe bandwidth (5 GT/s x8 link)
> > > bnx2x 0008:01:00.0 enP8p1s0f0: renamed from eth0
> > > bnx2x 0008:01:00.1: msix capability found
> > > bnx2x 0008:01:00.1: Using 64-bit DMA iommu bypass
> > > bnx2x 0008:01:00.1: part number 0-0-0-0
> > > bnx2x 0008:01:00.0 enP8p1s0f0: using MSI-X  IRQs: sp 267  fp[0] 269 ... fp[7] 276
> > > bnx2x 0008:01:00.0 enP8p1s0f0: NIC Link is Up, 10000 Mbps full duplex, Flow control: ON - receive & transmit
> > > bnx2x 0008:01:00.1: 32.000 Gb/s available PCIe bandwidth (5 GT/s x8 link)
> > > bnx2x 0008:01:00.1 enP8p1s0f1: renamed from eth0
> > > bnx2x 0008:01:00.2: msix capability found
> > > bnx2x 0008:01:00.2: Using 64-bit DMA iommu bypass
> > > bnx2x 0008:01:00.2: part number 0-0-0-0
> > > bnx2x 0008:01:00.1 enP8p1s0f1: using MSI-X  IRQs: sp 277  fp[0] 279 ... fp[7] 286
> > > bnx2x 0008:01:00.1 enP8p1s0f1: NIC Link is Up, 10000 Mbps full duplex, Flow control: ON - receive & transmit
> > 
> > 
> > > watchdog: CPU 80 self-detected hard LOCKUP @ opal_interrupt+0x28/0x70
> > > watchdog: CPU 80 TB:980794111093, last heartbeat TB:973959617200 (13348ms ago)
> > 
> > Ouch, 13 seconds in OPAL. Looks like we trip the hard lockup detector
> > once the thread comes back into the kernel so we're not completely
> > stuck. At a guess there's some contention on a lock in OPAL due to the
> > bind/unbind loop, but i'm not sure why that would be happening.
> > 
> > Can you give us a copy of the OPAL log? /sys/firmware/opal/msglog)
> 
> Oliver, thanks for looking into this, I have sent a private mail (file
> was 1MB) with logs attached.
> 

Oliver, any luck on the logs given.

Warnings also show up on 4.20.0-rc2-next-20181114

-- 
Regard's

Abdul Haleem
IBM Linux Technology Centre