DMA Mapping Error in ppc64

Sat Mar 24 19:19:50 AEDT 2018

On Fri, 2018-03-23 at 07:41 -0500, Jared Bents wrote:
> Thank you for the advice.  Looks like I get to try to rewrite the ath9k and ath10k drivers to use dma_alloc_coherent() instead of kmemdup() and dev_alloc_skb()

Euh no... dev_alloc_skb() is the right thing to do for receive
packets for a device driver.

The arch should be able to map that for DMA, even if include
bounce buffers via swiotlb.

Cheers,
Ben.

> On Thu, Mar 22, 2018 at 8:19 PM, Oliver <oohall at gmail.com> wrote:
> > On Fri, Mar 23, 2018 at 1:37 AM, Jared Bents
> > <jared.bents at rockwellcollins.com> wrote:
> > > Thank you for the response but unfortunately, it looks like I already
> > > have that and it is being used.  To verify, I commented that out and
> > > got the failure "dma_direct_alloc_coherent: No suitable zone for pfn
> > > 0xe0000".  Below is the code flow for function
> > > ath10k_pci_hif_exchange_bmi_msg which is showing the first dma mapping
> > > error.
> > >
> > > ath10k_pci_hif_exchange_bmi_msg -> dma_map_single ->
> > > dma_map_single_attrs -> swiotlb_map_page -> dma_capable (returns
> > > false)
> > >
> > >
> > > dma_capable is what reports the failure in that flow.
> > >
> > > static inline bool dma_capable(struct device *dev, dma_addr_t addr, size_t size)
> > > {
> > > #ifdef CONFIG_SWIOTLB
> > >     struct dev_archdata *sd = &dev->archdata;
> > >
> > >    if (sd->max_direct_dma_addr && addr + size > sd->max_direct_dma_addr)
> > >         return false;
> > > #endif
> > >
> > >     if (!dev->dma_mask)
> > >         return false;
> > >
> > >     return addr + size - 1 <= *dev->dma_mask;
> > > }
> > > Getting the below values:
> > > addr = 1ee376218
> > > size = 4
> > > sd->max_direct_dma_addr = e0000000 which is I believe DMA window size (e0000000)
> > >
> > > when executed sd->max_direct_dma_addr(e0000000) && addr(1ee376218) +
> > > size(4) becomes e0000004 which is > sd->max_direct_dma_addr (e0000000)
> > >
> > >
> > > So even though limit_zone_pfn(ZONE_DMA32, 1UL << (31 - PAGE_SHIFT)) is
> > > being used in arch/powerpc/platforms/85xx/corenet_generic.c,
> > 
> > > kmemdup(req, req_len, GFP_KERNEL) is returning an address that when
> > > sent to dma_map_single(), results in a bad map.
> > 
> > You need to use (GFP_KERNEL | GFP_DMA32) to constrain the allocations
> > to ZONE_DMA32. Without that the kmemdup() will allocate from any zone
> > so you'll probably get an unmappable address.
> > 
> > That said, the driver probably shouldn't be using kmemdup() here.
> > DMA-API.txt pretty explicitly says that drivers should not assume that
> > dma_map_single() will work with arbitrary memory. It should be using
> > dma_alloc_coherent() or a dma pool here.
> > 
> > > - Jared
> > >
> > > On Wed, Mar 21, 2018 at 11:54 PM, Oliver <oohall at gmail.com> wrote:
> > >> On Thu, Mar 22, 2018 at 8:00 AM, Jared Bents
> > >> <jared.bents at rockwellcollins.com> wrote:
> > >>> Hi all,
> > >>>
> > >>> Apologies for the amount of information but we've been debugging this
> > >>> for a while and I wanted to get what we are seeing captured as much as
> > >>> possible.  We are a T1042 processor and have a total 8GB DDR and our
> > >>> kernel version is fsl-sdk-v2.0-1703 (linux v4.1.35) as that is the
> > >>> latest version supplied by NXP.
> > >>>
> > >>> A while ago we ported from 32 bit to 64 bit.  Everything continued to
> > >>> work except the ath10k module we have.  So as a first step, we checked
> > >>> to see if an ath9k module also failed to work and it was also no
> > >>> longer working.  The ath10k is working fine on a 32 bit system but
> > >>> it's not working on 64 bit system as we are getting dma mapping errors
> > >>> when trying to initialize the wifi modules.
> > >>>
> > >>> pci_bus 0002:01: bus scan returning with max=01
> > >>> pci_bus 0002:01: busn_res: [bus 01] end is updated to 01
> > >>> pci_bus 0002:00: bus scan returning with max=01
> > >>> ath10k_pci 0000:01:00.0: unable to get target info from device
> > >>> ath10k_pci 0000:01:00.0: could not get target info (-5)
> > >>> ath10k_pci 0000:01:00.0: could not probe fw (-5)
> > >>> ath10k_pci 0001:01:00.0: Direct firmware load for
> > >>> ath10k/cal-pci-0001:01:00.0.bin failed with error -2
> > >>>
> > >>>
> > >>> First, we have tried the mainline kernel (v4.15)  to see if that would
> > >>> fix the issue, it did not.  So I made a patch for the ath10k driver to
> > >>> restrict to just GFP_DMA areas when allocating memory or creating
> > >>> sk_buffs and have attached it.  The ath10k wifi modules now initialize
> > >>> correctly but when I try to connect them and send traffic, they get a
> > >>> DMA mapping error from the sk_buff that it receives from elsewhere in
> > >>> the kernel.  So while the driver appears to be fixable with the patch,
> > >>> the modules are still unusable due to data being sent to the driver
> > >>> when ath10k_tx is called and it tries to dma map with the provided
> > >>> skb.  Also, according to the ath10k mailing list, GFP_DMA is not
> > >>> supposed to be used in general.  The error below is the same sort of
> > >>> dma mapping error that is seen when initializing the modules without
> > >>> the patch to OR with GFP_DMA.
> > >>>
> > >>> ath10k_pci 0001:01:00.0: failed to transmit packet, dropping: -5
> > >>>
> > >>>
> > >>> We asked on the ath10k mailing list if anyone else is having this
> > >>> problem and no one else seems to have the issue but they are using
> > >>> different architectures (ARM or X86). As a result, it does not seem to
> > >>> be a driver issue to us but something within the PowerPC arch.  So we
> > >>> dug a little deeper to try to find what addresses being mapped are
> > >>> working and what address being mapped are not working.
> > >>>
> > >>> We found that when the virtual address of data pointer (a member of
> > >>> sk_buff) is above ~3.7 GB RAM address range then return address from
> > >>> dma_map_single API is failed to validate in dma_mapping_error
> > >>> function.
> > >>>
> > >>> We also noticed that in a 64bit machine sometimes ping is working and
> > >>> because of the virtual address is under ~3.7GAM RAM address range.  So
> > >>> if we set mem=2048M in the bootargs, the ath10k module works
> > >>> perfectly, however this isn't a real solution since it cuts our
> > >>> available RAM from 8GB to 2GB.
> > >>
> > >> I think there's a known issue with the freescale PCIe root complex
> > >> where it can't DMA beyond the 4GB mark. There's a workaround in
> > >> the form of limit_zone_pfn() which you can use to put the lower 4GB into
> > >> ZONE_DMA32 and allocate from there rather than ZONE_NORMAL.
> > >> For details of how to use it have a look at corenet_gen_setup_arch() in
> > >> arch/powerpc/platforms/85xx/corenet_generic.c
> > >>
> > >> Hope that helps,
> > >> Oliver
> 
> 