[PATCH v2 1/9] powerpc/eeh: Remove eeh_handle_event()

Alexey Kardashevskiy aik at ozlabs.ru
Wed Mar 21 16:17:29 AEDT 2018


On 19/3/18 1:46 pm, Sam Bobroff wrote:
> The function eeh_handle_event(pe) does nothing other than switching
> between calling eeh_handle_normal_event(pe) and
> eeh_handle_special_event(). However it is only called in two places,
> one where pe can't be NULL and the other where it must be NULL (see
> eeh_event_handler()) so it does nothing but obscure the flow of
> control.
> 
> So, remove it.
> 
> Signed-off-by: Sam Bobroff <sam.bobroff at au1.ibm.com>


Reviewed-by: Alexey Kardashevskiy <aik at ozlabs.ru>


> ---
>  arch/powerpc/include/asm/eeh_event.h |  3 ++-
>  arch/powerpc/kernel/eeh_driver.c     | 42 +++++++++++++-----------------------
>  arch/powerpc/kernel/eeh_event.c      |  4 ++--
>  3 files changed, 19 insertions(+), 30 deletions(-)
> 
> diff --git a/arch/powerpc/include/asm/eeh_event.h b/arch/powerpc/include/asm/eeh_event.h
> index 1e551a2d6f82..0a168038882d 100644
> --- a/arch/powerpc/include/asm/eeh_event.h
> +++ b/arch/powerpc/include/asm/eeh_event.h
> @@ -34,7 +34,8 @@ struct eeh_event {
>  int eeh_event_init(void);
>  int eeh_send_failure_event(struct eeh_pe *pe);
>  void eeh_remove_event(struct eeh_pe *pe, bool force);
> -void eeh_handle_event(struct eeh_pe *pe);
> +bool eeh_handle_normal_event(struct eeh_pe *pe);
> +void eeh_handle_special_event(void);
>  
>  #endif /* __KERNEL__ */
>  #endif /* ASM_POWERPC_EEH_EVENT_H */
> diff --git a/arch/powerpc/kernel/eeh_driver.c b/arch/powerpc/kernel/eeh_driver.c
> index 0c0b66fc5bfb..51b21c97910f 100644
> --- a/arch/powerpc/kernel/eeh_driver.c
> +++ b/arch/powerpc/kernel/eeh_driver.c
> @@ -738,9 +738,22 @@ static int eeh_reset_device(struct eeh_pe *pe, struct pci_bus *bus,
>   * Attempts to recover the given PE.  If recovery fails or the PE has failed
>   * too many times, remove the PE.
>   *
> + * While PHB detects address or data parity errors on particular PCI
> + * slot, the associated PE will be frozen. Besides, DMA's occurring
> + * to wild addresses (which usually happen due to bugs in device
> + * drivers or in PCI adapter firmware) can cause EEH error. #SERR,
> + * #PERR or other misc PCI-related errors also can trigger EEH errors.
> + *
> + * Recovery process consists of unplugging the device driver (which
> + * generated hotplug events to userspace), then issuing a PCI #RST to
> + * the device, then reconfiguring the PCI config space for all bridges
> + * & devices under this slot, and then finally restarting the device
> + * drivers (which cause a second set of hotplug events to go out to
> + * userspace).
> + *
>   * Returns true if @pe should no longer be used, else false.
>   */
> -static bool eeh_handle_normal_event(struct eeh_pe *pe)
> +bool eeh_handle_normal_event(struct eeh_pe *pe)
>  {
>  	struct pci_bus *frozen_bus;
>  	struct eeh_dev *edev, *tmp;
> @@ -942,7 +955,7 @@ static bool eeh_handle_normal_event(struct eeh_pe *pe)
>   * specific PE.  Iterates through possible failures and handles them as
>   * necessary.
>   */
> -static void eeh_handle_special_event(void)
> +void eeh_handle_special_event(void)
>  {
>  	struct eeh_pe *pe, *phb_pe;
>  	struct pci_bus *bus;
> @@ -1049,28 +1062,3 @@ static void eeh_handle_special_event(void)
>  			break;
>  	} while (rc != EEH_NEXT_ERR_NONE);
>  }
> -
> -/**
> - * eeh_handle_event - Reset a PCI device after hard lockup.
> - * @pe: EEH PE
> - *
> - * While PHB detects address or data parity errors on particular PCI
> - * slot, the associated PE will be frozen. Besides, DMA's occurring
> - * to wild addresses (which usually happen due to bugs in device
> - * drivers or in PCI adapter firmware) can cause EEH error. #SERR,
> - * #PERR or other misc PCI-related errors also can trigger EEH errors.
> - *
> - * Recovery process consists of unplugging the device driver (which
> - * generated hotplug events to userspace), then issuing a PCI #RST to
> - * the device, then reconfiguring the PCI config space for all bridges
> - * & devices under this slot, and then finally restarting the device
> - * drivers (which cause a second set of hotplug events to go out to
> - * userspace).
> - */
> -void eeh_handle_event(struct eeh_pe *pe)
> -{
> -	if (pe)
> -		eeh_handle_normal_event(pe);
> -	else
> -		eeh_handle_special_event();
> -}
> diff --git a/arch/powerpc/kernel/eeh_event.c b/arch/powerpc/kernel/eeh_event.c
> index accbf8b5fd46..872bcfe8f90e 100644
> --- a/arch/powerpc/kernel/eeh_event.c
> +++ b/arch/powerpc/kernel/eeh_event.c
> @@ -81,10 +81,10 @@ static int eeh_event_handler(void * dummy)
>  				pr_info("EEH: Detected PCI bus error on "
>  					"PHB#%x-PE#%x\n",
>  					pe->phb->global_number, pe->addr);
> -			eeh_handle_event(pe);
> +			eeh_handle_normal_event(pe);
>  			eeh_pe_state_clear(pe, EEH_PE_RECOVERING);
>  		} else {
> -			eeh_handle_event(NULL);
> +			eeh_handle_special_event();
>  		}
>  
>  		kfree(event);
> 


-- 
Alexey


More information about the Linuxppc-dev mailing list