usb: dwc2: regression on MyBook Live Duo / Canyonlands since 4.3.0-rc4

Christian Lamparter chunkeey at googlemail.com
Sun May 8 21:44:18 AEST 2016


On Sunday, May 08, 2016 08:40:55 PM Benjamin Herrenschmidt wrote:
> On Sun, 2016-05-08 at 00:54 +0200, Christian Lamparter via Linuxppc-dev 
> wrote:
> > I've been looking in getting the MyBook Live Duo's USB OTG port
> > to function. The SoC is a APM82181. Which has a PowerPC 464 core
> > and related to the supported canyonlands architecture in
> > arch/powerpc/.
> > 
> > Currently in -next the dwc2 module doesn't load: 
> 
> Smells like the APM implementation is little endian. You might need to
> use a flag to indicate what endian to use instead and set it
> appropriately based on some DT properties.
I tried. As per common-properties[0], I added little-endian; but it has no
effect. I looked in dwc2_driver_probe and found no way of specifying the
endian of the device. It all comes down to the dwc2_readl & dwc2_writel
accessors. These - sadly - have been hardwired to use __raw_readl and
__raw_writel. So, it's always "native-endian". While common-properties
says little-endian should be preferred.

> > dwc2 4bff80000.usbotg: dwc2_core_reset() HANG! AHB Idle GRSTCTL=80
> > dwc2 4bff80000.usbotg: Bad value for GSNPSID: 0x0a29544f
> > 
> > Looking at the Bad GSNPSID value: 0x0a29544f. It is obvious that
> > this is an endian problem. git finds this patch:
> > 
> > commit 95c8bc3609440af5e4a4f760b8680caea7424396
> > Author: Antti Seppälä <a.seppala at gmail.com>
> > Date:   Thu Aug 20 21:41:07 2015 +0300
> > 
> >     usb: dwc2: Use platform endianness when accessing registers
> > 
> >     This patch is necessary to access dwc2 registers correctly on
> > big-endian
> >     systems such as the mips based SoCs made by Lantiq. Then dwc2 can
> > be
> >     used to replace ifx-hcd driver for Lantiq platforms found e.g. in
> >     OpenWrt.
> >     
> >     The patch was autogenerated with the following commands:
> >     $EDITOR core.h
> >     sed -i "s/\<readl\>/dwc2_readl/g" *.c hcd.h hw.h
> >     sed -i "s/\<writel\>/dwc2_writel/g" *.c hcd.h hw.h
> >     
> >     Some files were then hand-edited to fix checkpatch.pl warnings
> > about
> >     too long lines.
> > 
> > which unfortunately, broke the USB-OTG port on the MyBook Live Duo.
> > Reverting to the readl / writel:
> > 
> > --- 
> > diff --git a/drivers/usb/dwc2/core.h b/drivers/usb/dwc2/core.h
> > index 3c58d63..c021c1f 100644
> > --- a/drivers/usb/dwc2/core.h
> > +++ b/drivers/usb/dwc2/core.h
> > @@ -66,7 +66,7 @@
> >  
> >  static inline u32 dwc2_readl(const void __iomem *addr)
> >  {
> > -	u32 value = __raw_readl(addr);
> > +	u32 value = readl(addr);
> >  
> >  	/* In order to preserve endianness __raw_* operation is
> > used. Therefore
> >  	 * a barrier is needed to ensure IO access is not re-ordered 
> > across
> > @@ -78,7 +78,7 @@ static inline u32 dwc2_readl(const void __iomem
> > *addr)
> >  
> >  static inline void dwc2_writel(u32 value, void __iomem *addr)
> >  {
> > -	__raw_writel(value, addr);
> > +	writel(value, addr);
> >  
> >  	/*
> >  	 * In order to preserve endianness __raw_* operation is
> > used. Therefore
> > 
> > ---
> > 
> > restores the dwc-otg port to full working order:
> > dwc2 4bff80000.usbotg: Specified GNPTXFDEP=1024 > 256
> > dwc2 4bff80000.usbotg: EPs: 3, shared fifos, 2042 entries in SPRAM
> > dwc2 4bff80000.usbotg: DWC OTG Controller
> > dwc2 4bff80000.usbotg: new USB bus registered, assigned bus number 1
> > dwc2 4bff80000.usbotg: irq 33, io mem 0x00000000
> > hub 1-0:1.0: USB hub found
> > hub 1-0:1.0: 1 port detected
> > root at mbl:~# usb 1-1: new high-speed USB device number 2 using dwc2
> > 
> > So, what to do?
     ^^^

Regards,
Christian

[0] <http://lxr.free-electrons.com/source/Documentation/devicetree/bindings/common-properties.txt>



More information about the Linuxppc-dev mailing list